NitroOBD2 for Gas / Petrol Engines: Yellow--The Green ECO version for gas engines & the RED version for Diesel vehicles are available in our other listings
NitroOBD2 : More Power / More Torque
NitroOBD2 is a Plug&Drive Ready device to function
the increasing the performance of engine.
NitroOBD2 is easy to install. Just plug it into the OBD2
connector of vehicles. NitroOBD2 fits all cars from 1996.
It works based OBD2 protocols as remapping the Car's
computer ECU. After driving 200 km road total, NitroOBD2 adjusts itself to the
car, according to the drivers' habits and always keeps remapping the ECU to
increase the performance of engine.
What does NitroOBD2 do?
According to your driving habits, NitroOBD2 makes new map in the car's computer
ECU to increase the performance of your car.
As you driving much more KM/Mile, it renews the map. Thus
it keeps the vehicle's power and torque increasing.
What is NitroOBD2 Chip Tuning Box?
NitroOBD2 is a Chip Tuning Box which can be plugged into
OBD2 connector of your car to increase the performance of your car.
When it plugged
into OBD2 connector, NitroOBD2 receives the information from the car computer
ECU. With the received data from ECU
NitroOBD2 adjusts the boost pressure, quantity of fuel,
injection timing and pressure to increase the performance of your car.
NitroOBD2 Chip Tuning Box does not exceed the
manufacturer requirements. It works only within the tolerance of the engine.
NitroOBD2 finds out the hidden power of your car.
NitroOBD2 does not damage the engine and the car computer ECU or not cause any
negative effects to the car factory setting.
NitroOBD2 does not change any of the settings
permanently. To turn back to the car's original settings, just unplug NitroOBD2
from OBD2 connector.
NitroOBD2 finds out the hidden power of your car.
- Up to 35% more power
- Up to 25 % more torque
NitroOBD2 is very easy to use.
Installation and Calibration
1 - Pull the Car Key out from the ignition.
2 - Find OBD2 connector(*) in your car and Plug in Nitro OBD2
3 - Insert the key into the ignition and twist the key to
the first stage. (Do not start the car)
4 - Press the reset button for about 5 sec. After
releasing the button, just wait for a while about 30-54 sec. (NitroOBD2 will
communicate and establish connection with ECU)
5 - Start up the engine.
NitroOBD2 settings are optimal and the best for your car.
Even the parameters are different for each vehicle there might not be a need to
make an additional adjustment. NitroOBD2 will recognize your vehicle and your
driving habits after around 200 km/150 miles driving, and then NitroOBD2
adjusts itself to match your car perfectly.
NitroOBD2 works on the basis of changing the signal from the ECU. As a consequence, it changes the whole injection map.
The main difference between NitroOBD2 Chip Tuning Box and
Remapping tuning methods is that NitroOBD2 Chip Tuning Box is easily removable,
and after unplug you go back to the factory settings.
NitroOBD2 is the cheap and safe type of tuning. Remapping is a permanent change to your car. This is the
expensive tuning and you cannot remove it.
NitroOBD2 is equipped with the engine protection function
and 100% safe for your car engine.
NitroOBD2 produced on the printed circuit board in SMD
technology. NitroOBD2 Chip Tuning Boxes are high quality.
Does your car have OBD2 connector?
On-Board Diagnostics, or "OBD," is a
computer-based system built into all 1996 and later light-duty vehicles and
trucks, as required by the Clean Air Act Amendments of 1990.
OBD systems are designed to monitor the performance of
some of an engine's major components including those responsible for
controlling emissions.
OBD2 necessary for cars:
- Sold after January 1, 1996 in the USA
- Sold after January 1, 2001 in the European Union
- With diesel engine sold after January 1, 2003
Where is the OBD2 connector located in your car? Check the owners book or see possibilities below
1 Driver's side, underneath dashboard, in the area under
the steering column
2 Driver's side, underneath dashboard between the
driver-side door and steering column area
3 Driver's side, underneath dashboard between the steering column area and the
center console
4 Driver's side, dashboard instrument/gauge area, between
the steering column and center console
5 Driver's side, dashboard instrument/gauge area, between
the driver-side door and steering column
6 Center console, vertical surface left of vehicle center line
7 Center console, vertical surface right of vehicle center line or on passenger side of center console
8 Center console, horizontal surface in front passenger area.
Certificates : CE / FCC /
RoHS
Package contents:
- NitroOBD2 Chip Tuning Box Interface
- User Manual English
Testimonials from actual users
DON R - Amazing, an immediate improvement in power and much smoother
DAVE S - Actually works! Much better acceleration from a stop!
LARRY N - I didnt expect it to work this well