Home About Us Product Range SupportContact Us
 
 

C-Bus Compatible Controlled Motorised Roller Blinds Kit, Group Control(No Remote Control)

 

If you are looking for Remote Control Motorised Roller Blinds Kit, click below link

http://www.ebay.com.au/itm/Remote-Control-Motorised-Roller-Blinds-Kit-Group-Control-DIY-/121723076229

 

C-BUS Controlled Blinds System

Do you want to save money on window blinds and motorise them at the same time

Are you tired of over priced and expensive quotes from blind retailers

If yes then you have come to the right place!

Blinds & Curtain Automation is offering a quality solution for a limited time only!

 

YOUR 'BUY IT NOW' IS PAYING AS BELOW

1)One tubular motor,

2)One pair of metal bracket,

3)One spring loaded end pin,

4)One drive wheel & Crown  for 43mm tube,

5)One length of 43mm aluminium tube

Completed Assembly Blinds ready for installation available, please check prices & fabrics at our website : www.autoblinds.com.au

Illustration of blinds assembly with the components (as a guide)

1) Tubular Motor
2) Aluminium Tube
3) End Cap
4) a) Blind Fabric (Blockout) , b) Blind Fabric (Sunscreen)
5) Plastic Strip
6) Close Caps Bottom Bar
7) Brackets
8) Screws
9) Adhesive Strip
10) Bottom Tube

 

Detailed description of TUBULAR MOTOR

Features:

10 kgs lifting capacity
3 meters Aluminium tube length capacity
5 years Warranty (Serviced or Replaced locally in Australia)
Cord connector for easy removing & connection
Easy limit setting

Specifications:

240V/50Hz ( Please check your countries power supply specifications)
35mm Diameter
100 Power (W)
0.44 Current (A)
5 Torque (Nm)
28 Speed (R/Min)
Motor Weight : 1.2 kgs
Motor lenght : 460mm
Packing: 500mm x 90mm x 70mm
Gross packing weight : 1.4 kgs


 

Detailed description of all other components

TOP ALUMINIUM TUBE (43mm diameter tube for blinds length less then 2500mm) (50mm diameter tube for blinds more than 2500mm )

END PIN

BRACKETS (Comes in pairs. One of the brackets is holding the motor; the other bracket is holding the END PIN)

Suitable for face fit & recess fit, easy remove & install. The gap between bracket and motor = 17mm, bracket between end pin =13mm, Total gap =30mm.

Note: we may use similar end pin and brackets as alternative (will not affect quality or operation) 

 

Tubular Motor C-BUS Instructions
TUBULAR MOTOR C-BUS INSTRUCTIONS

 

Terms & Conditions

*Postage & Packing Costs Free To Metropolitan Area

*Blinds System components only available with the purchase of the motor
*Go to http://www.autoblinds.com.au for support / installation on the products
*Look out for our other products including Electric Curtain System, Electric Roller Blind System, C-Bus Motor, Blinds motor
*PO Box delivery addresses not accepted, please supply alternative address.
*Contact phone number must supply for the courier/fright.

 

 

We are a legitimate registered Australian based company. There is absolutely no catches, satisfaction guaranteed.

We invite you to compare our prices and quality

Postage & Packing Costs Free To Metropolitan Area

NOTE: NO P O BOX ADDRESS.

MUST HAVE YOUR PHONE CONTACT NUMBER PROVIDE FOR THE COURIER

ALLOW TO LEAVE PARCELS, IF NO ONE AT HOME

Your items are not insured, Insurance are an additional cost

Postage Charges for International buyers:
Supply your own service

Feel free to contact me for any questions or quotations. Tel : 03-9893 4029

Website: http://www.autoblinds.com.au

Autoblinds (formerly trading as Blinds & Curtain Automation - Same Management)