All video guides are available below. See how easy it is.

                           

 

             (Except. Fuser reset cable)                      

- All instruction manuals are in English unless otherwise specified.

 

 

 

How to use our Drum Reset Chip? Watch the short video below. This is really easy to save time, money and the earth.

                             

                                                             

                             

                             

Transfer Belt Reset. Even if your transfer belt looks a bit different, the way of installation is same. Refer to the video below

                             

                                                             

                             

 

                             

Fuser resetter for A3 Printers with following fuser connecter. Check from under-surface of your existing fuser.(ABPSJ13 Type)

                             

                                                                                           

                             

 

                             

 

                             

FUSER reset cable. You must open 4 screws to access to the motherboard of your printer to install this cable. If you are worried about opening

                             

your printer or having difficulties of moving your printers, better to buy RESETTER type above.

                                                         

                           

 

                             

 

                             

If your fuser unit has similar connectors as below, please contact us with your printer model number before purchasing.

                             

                                                                                           

                                                       

                           

             

 

             

 

 

 

 

 

FAQs

 

Does it reset TONER level? : NO

This is a drum reset chip and this will only reset the drum counter only. If you need to reset your toner counter before/after toner refill, you need to buy the toner reset chips. Unfortunately, we do not sell the toner reset chip for Samsung models currently.

 

 

What is the reset chip(kit) for drum / fuser / transfer belt and  what is the main benefit of using this? Why should we reset the counters?

Based on our experience, usually the drum units and other parts such  as Transfer belt and fuser unit are physically strong enough to work for one or  two more cycles of its stated life time. However, almost all laser printers  have built-in counter system which will generate a message to the user to order  new part and eventually lock up the printer (with “Replace Drum”  or “Replace  Part” message) when it reaches its stated printing limit regardless the  physical condition of the parts. Even though the physical condition of the  parts are still good enough and the printing quality is still acceptable, the  users had no options to keep using the existing parts but had to change. This  is a huge waste of time, money and environmentally not friendly.

Now, users can use our counter reset chips/kits to renew the counter  (which will reset the remaining life of the part back to 100% and remove the  printer lock up action) and use the same part for one more cycle without  replacing the part. This solution does not repair any print defects. So, this  solution may be used if the printing quality of the last printed page is still  acceptable. Each counter reset requires a new chip. This will save you money,  time and also save environment.

 

 

How does the reset chip work?

 When a new part is installed, the motherboard will receive a special  signal from the part. This happens only once upon the first installation of the  part. Then the motherboard will set the page count of the part to zero. If the  printer was locked up due to the counter hit the threshold prior to the part  replacement, then, this counter reset action will unlock the printer. Then, the  printer will change the character of the special circuit to prevent reusing the  part in another printer or in the same printer in the future after the stated  life span. This is why the counter reset event will happen only once on the first  installation of the part.

Our reset chip has same function as the one from a new part. The  printers will never know the physical condition of the part installed. If the  used part is reinstalled but with a new chip attached, the printer will simply  assume that the part is a new one and reset the counter back to 0 and the  remaining life of the part is reset back to 100%.

 

 

Very important things to know before purchasing.

If you are looking for toner counter reset, this is not a right  products. You need to buy toner reset chips. This listing is for drum / fuser  or transfer belt counter reset chips. Please see the compatible model list and  description before committing purchase.

The part that you intend to reset must be in good working condition  or had been providing good quality prints until it was locked by the counter.  If the part has any physical defects, this chip will not improve the printing defects  or quality at all. If you are having printing quality problems or error codes  other than the "replace part”  light message, this kit will not help.

Please note that all brand names and trademarks are the property of  their respective owners and are used for descriptive purposes only. This  product is a compatible product, not an O.E.M. Product.

 

 

We are looking for distribution partners worldwide (except UK, US and Canada)

If you would like to be one of our distribution partners / resellers, please feel free to contact us.

 

Sticker Chip Series from ABPS. Just simply peel and stick.

No Tools required. No Hacking / No Welding.
  No toner proof vacuum cleaner required.

Watch Youtube video clip about installation of this chip
  http://www.youtube.com/watch?v=ZlSpMjOS6UI
  This sample video is for Xerox Phaser 7400 Series which has exactly same physical size drum units, so, the way of using the chips are same.

Other drum reset fuses being sold on the eBay require more than 20 min work per drum unit. Opening a drum from OKI A3 Printers is not easy at all, and it will introduce a lot of toner leaking during the job. Why not try our simple Peel & Stick Sticker Chip. Using our Sticker Chip, resetting a drum takes less than 2 min.

 

This is a twin pack, and you can use two chips for any two colour drums at your own choice. The chips are universal and can be used for any color drum unit.

just Peel and Stick when you get the drum replacement message from your printer.
  Extend your drum life up by using this chips. Re-use your drum up to two times.
  Full instruction is provided with the chip.

No Welding / No Soldering Required.
  No Firmware Hacking
  DIY within 1 min.

Save your Time and £££.

Even easier than a drum unit replacement. No need to remove the toner cartridge during the job.
  Reset the message of "Replace OPC Drum" and reset drum life back to 100%

Important things to know before purchase
  If you have any printing quality issue caused by the drum unit, please be advised that this chip will not fix the drum unit's physical damages. This will not improve the printing quality caused by the drum unit.

Our chips work on both Starter version and retail/regular version drums.
  The other's reset fuse/chips cannot reset Starter Version Drum.