| 1.0 |
Load Type |
AC Motor |
| 2.0 |
Rating |
|
| 2.1 |
Horsepower |
3 |
| 2.2 |
Motor (kW) |
2.2 |
| 2.3 |
Capacity (kVA) |
4.5 |
| 2.4 |
Output Current (Amps) |
11 |
| 3.0 |
Rated Input |
|
| 3.1 |
Input Voltage |
200 - 240VAC ±10% |
| 3.2 |
Phase |
1 |
| 3.3 |
Frequency |
50/60 ±5% |
| 4.0 |
Rated Output |
|
| 4.1 |
Voltage |
200 - 240VAC ±10% |
| 4.2 |
Phase |
3 |
| 4.3 |
Frequency |
0.5 - 400 Hz |
| 5.0 |
Control Method |
Sine-Wave (PWM) control |
| 6.0 |
Frequency Range |
0.5 - 400 Hz |
| 7.0 |
Frequency Accuracy |
|
| 7.1 |
Digital Command |
± 0.01% of the max. frequency |
| 7.2 |
Analog Command |
± 0.2% of the max. frequency |
| 8.0 |
Frequency Setting Resolution |
|
| 8.1 |
Digital |
0.1 Hz |
| 8.2 |
Analog |
Max. Freq./100 |
| 9.0 |
Volt./Freq. Characteristics |
Setting available for constant torque, reduced torque, sensorless vector |
| 10.0 |
Overload Current Rating |
150%, 60 seconds |
| 11.0 |
Acceleration/Deceleration Time |
0.1 ~ 3000 sec. (linear/curve, accel./decel.) Second stage accel./decel. setting available |
| 12.0 |
Braking |
|
| 12.1 |
Dynamic Braking |
Approx. 100% |
| 12.2 |
DC Braking |
Operating frequency, time and braking force variable |
| 13.0 |
Input Signal |
|
| 13.1 |
Frequency Setting |
|
| 13.1.1 |
Digital Operator Panel |
Up(1) and Down(2) keys/value setting keys |
| 13.1.2 |
Potentiometer |
Analog Setting |
| 13.1.3 |
External Signal |
0 ~ 10 VDC (input impedence 10k ohms), 4 ~ 20 mA (input impedence 250k ohms) Potentiometer: 1k to 2k ohms, variable resistor.
The frequency command is the maximum frequency at 9.8V for input voltage 0 - 10 VDC, or at 19.6 mA for input current 4 ~ 20 mA.
If this characteristic is not convenient contact Drives Warehouse. |
| 13.2 |
Forward/Reverse/Start/Stop |
|
| 13.2.1 |
Digital Operator Panel |
Run/Stop (Forward/Reverse run change by command) |
| 13.2.2 |
External Signal |
Forward RUN/STOP (1a contact) |
| 13.3 |
Intelligent Input Terminals |
FW (Forward run command), RV (reverse run command, CF1~CF4 (multi-stage speed setting), JG (jogging command), 2CH (2-stage acceleration/deceleration command),
FRS (free run stop command), EXT (external trip), USP (USP function), SFT (soft lock), AT (analog current input select signal), RS (reset), PTC (thermal protection). |
| 14.0 |
Output Signal |
|
| 14.1 |
Intelligent Output Terminal |
RUN (running signal), FA1,2 (frequency arrival signal), OL (overload advance notice signal), OD (deviation signal at PID control), AL (alarm signal) |
| 14.2 |
Frequency Monitor |
PWM output: Select analog output frequency monitor, analog output current monitor or digital output frequency monitor |
| 15.0 |
Other Functions |
AVR function, upper/lower limiter, PID control, carrier frequency change, frequency jump, electronic thermal level adjustment, gain/bias setting function, retry function |
| 16.0 |
Protective Function |
Overcurrent, overvoltage, undervoltage, overload, extreme high/low temperature, CPU error, memory error, ground fault detection at startup, internal communication error. |
| 17.0 |
Environmental Conditions |
|
| 17.1 |
Operating Temp. |
-10 ~ 50ºC |
| 17.2 |
Storage Temp. |
-10 ~ 70ºC |
| 17.3 |
Humidity |
20 ~ 90 % RH (no condensation) |
| 17.4 |
Vibration |
5.9 m/s² (0.6G), 10 ~ 55 Hz |
| 17.5 |
Location |
Less than 1000 m of altitude or less, indoors (no corrosive gases or dust) |
| 18.0 |
Mechanical Properties |
|
| 18.1 |
Color |
Black |
| 18.2 |
Height |
5.04 inches (128mm) |
| 18.3 |
Width |
4.25 inches (108mm) |
| 18.4 |
Depth |
6.71 inches (170.5mm) |
| 18.5 |
Weight (lbs) |
4.0 |
| 19.0 |
Options |
Remote operator Dynamic braking resistor AC reactor DC reactor Noise filter |
