New & Genuine HPI RACING 112851 - FLUX EMH-3S BRUSHLESS ESC for BLITZ FLUX & Savage XS
For Bullet FLUX MT ST / Savage Flux XS and other 1/10 rc cars
USE WITH FLUX MMH-4000KV BRUSHLESS MOTOR
Upgrade your brushless speed controller to the latest tech from HPI!
The all-new Flux EMH-3S electronic speed controller is just as adjustable as the Flux Reload V2 it replaces but it's more powerful and more efficient to handle bigger motors and higher capacity battery packs for increased speeds and fun!
The Flux EMH-3S is being fitted in the latest Flux-powered HPI kits because it's ultra-versatile, super-powerful and ready for anything. Snow? Mud? Rain? Bogs? It can take it all! It's completely sealed so it's perfectly dustproof and waterproof, making it the ideal solution for powering any kind of on- or off-road 1/10th scale car, buggy or truck.
The Flux EMH-3S is extremely adjustable, which makes it great for all kinds of 1/10th scale vehicles:
Features
3 Running Modes:
Racing (Forward and Brake only)
Bashing (Forward, Brake and Reverse)
Rock Crawler (instant switch from Forward to Reverse)
8 steps of Drag Brake adjustment from 0-100%
6 Auto-LiPo Cut Off settings: none or 2.5V-3.4V per cell
9 Punch Start Mode settings from soft to aggressive
4 steps of Maximum Brake Force adjustment from 25-100%
4 steps of Maximum Reverse Force adjustment from 25-100%
3 steps of Initial Brake Force adjustment from 0-40%, plus option to make IBF equal Drag Brake setting
3 steps of Neutral Range adjustment from 6-12%
8 steps of Motor Timing adjustment from 0-26.25 degrees
Overheat Protection on/off selection
Multiple protection features:
Auto-LiPo detection
Low voltage cut off protection for LiPo or NiMH/NiCd battery
Overheat protection for the ESC
Throttle signal loss protection
Easily programmed with only one setup button, and is compatible with the pocket sized 2 in 1 professional program card. (Available separately as #101280)
Specification:
Constant Current: 80A - Reload V2 was 60A!
Burst Current: 540A - Reload V2 was 190A!
Resistance: 0.0004 ohm
Application: 1/10th scale On-Road/Off-Road
Battery Limit: 4-9 Cells NiMH or 2-3S LiPo
Motor Limit:
2S LiPo or 6 Cell NiMH: On-Road 5.5T, Off-Road 6000 kV
3S LiPo or 9 Cell NiMH: On-Road 8.5T, Off-Road 4000 kV
BEC: 6V/2A
Motor Type: Sensorless Brushless
Dimensions: 50.5 x 56.2 x 35.4m
Waterproof!
Compatible with #101856 - FLUX RELOAD ESC PROGRAM BOX V2 - please make sure the program box is updated to the latest firmware.
Use with motor #112850 - FLUX MMH-4000KV BRUSHLESS MOTOR
Upgrade your brushless speed controller to the latest tech from HPI!
The all-new Flux EMH-3S electronic speed controller is just as adjustable as the Flux Reload V2 it replaces but it's more powerful and more efficient to handle bigger motors and higher capacity battery packs for increased speeds and fun!
The Flux EMH-3S is being fitted in the latest Flux-powered HPI kits because it's ultra-versatile, super-powerful and ready for anything. Snow? Mud? Rain? Bogs? It can take it all! It's completely sealed so it's perfectly dustproof and waterproof, making it the ideal solution for powering any kind of on- or off-road 1/10th scale car, buggy or truck.
The Flux EMH-3S is extremely adjustable, which makes it great for all kinds of 1/10th scale vehicles:
- buggies
- touring cars
- scalers
- drifters
- Mini racers
- crawlers
- desert buggies
- vintage touring cars
- stadium trucks
- short course trucks
- desert trucks
Features
3 Running Modes:
Racing (Forward and Brake only)
Bashing (Forward, Brake and Reverse)
Rock Crawler (instant switch from Forward to Reverse)
8 steps of Drag Brake adjustment from 0-100%
6 Auto-LiPo Cut Off settings: none or 2.5V-3.4V per cell
9 Punch Start Mode settings from soft to aggressive
4 steps of Maximum Brake Force adjustment from 25-100%
4 steps of Maximum Reverse Force adjustment from 25-100%
3 steps of Initial Brake Force adjustment from 0-40%, plus option to make IBF equal Drag Brake setting
3 steps of Neutral Range adjustment from 6-12%
8 steps of Motor Timing adjustment from 0-26.25 degrees
Overheat Protection on/off selection
Multiple protection features:
Auto-LiPo detection
Low voltage cut off protection for LiPo or NiMH/NiCd battery
Overheat protection for the ESC
Throttle signal loss protection
Easily programmed with only one setup button, and is compatible with the pocket sized 2 in 1 professional program card. (Available separately as #101280)
Specification:
Constant Current: 80A - Reload V2 was 60A!
Burst Current: 540A - Reload V2 was 190A!
Resistance: 0.0004 ohm
Application: 1/10th scale On-Road/Off-Road
Battery Limit: 4-9 Cells NiMH or 2-3S LiPo
Motor Limit:
2S LiPo or 6 Cell NiMH: On-Road 5.5T, Off-Road 6000 kV
3S LiPo or 9 Cell NiMH: On-Road 8.5T, Off-Road 4000 kV
BEC: 6V/2A
Motor Type: Sensorless Brushless
Dimensions: 50.5 x 56.2 x 35.4m
Waterproof!
Compatible with #101856 - FLUX RELOAD ESC PROGRAM BOX V2 - please make sure the program box is updated to the latest firmware.
Use with motor #112850 - FLUX MMH-4000KV BRUSHLESS MOTOR
Removed from a brand new genuine HPI Blitz FLUX as in the pictures below.
Item is in UK ready for same day dispatch with Royal Mail 1st class.
As an RC enthusiast I know it can be frustrating waiting for parts. This is why I make sure items get to you ASAP (Usually next day)
Please allow 3 to 4 working days for international sales but sometimes it can take up to 14 days.
Buy from trusted eBayer with 100% positive feedback!
14 day money back guarantee whatever the reason as long it is returned in the same condition as it was dispatched.
Check out my other listings for more HPI Blitz stuff!
Terms of sale & note to Scamers:
Don't waste your time and my time sending back an old part asking for a refund. You will be reported to local authorities and ebay! Due to the nature of the hobby there is no warranty on any parts. Engines can not be sent back once they have had fuel in them. 14 day money back only applies if the item is sent back in the same condition as I sent it to you. If you ordered the wrong part then you will get a full refund minus what the postage cost me to send the item to you. If I sent you the wrong or faulty part I will cover yours and my postage cost.
Thanks for looking, Kev :)