Note: The color of the item may vary slightly due to photography and your own computer
Stable performance and low power consumption
Adopt fixed wireless code encoding,Wireless RF remote control,has no direction
Mainly apply into electrical control circuit such as anti-theft alarm, remote control electric windows, signal control, industrial control lifting equipment and so on.
Specifications:
Work Mode: Inching mode,Self-lock mode, Interlocked mode
Encoding type: fixed code; pad code
Working voltage: DC 12V
Frequency: 315MHZ
Contact capacity: ≤ 10A/250VAC; 10A/30VDC
Receiver sensitivity: >-105dB
Control channel: four normally open (normally closed) contacts
Remote control distance:1000 meters(Theoretical distance)
Dimensions: 7.2 x 5 x 2.5cm/2.83 x 1.97 x 0.98"(L x W x H)
Weight: 113g

Operation Way and Steps:
1. Factory Default is Inching Mode.
Press and hold the button A, the Receiver A (Relay A)turns on; Release the button A, the Receiver A (Relay A) turns off.
2. Each transmitter and receiver have been finished linking and factory default mode(Self-lock Mode) has been set up. When you receive them, you do not need to link again, you just need to connect the wiring according to our wiring diagram layout.

There are 3 modes:
1)Inching: Press and hold the button A, the Receiver A (Relay A)turns on; Release the button A, the Receiver A (Relay A) turns off.
2)Self-lock : Press the button A, the Receiver A (Relay A) turns on; Press the button A again, the Receiver A (Relay A) turns off.
3)Interlocked:
Press the button A, the Receiver A (Relay A) turns on; Press the button B, the Receiver B (Relay B) turns on, the Receiver A (Relay A) turns off.

If you want to change the factory default mode to other two working modes, the operation steps as below:
1. Clear:
Press and hold the learning button on the receiver board, the red light (Signal Light) will turn on and stay on for about 5 seconds, till the red light turns off, then release the learning button. It means clearing succeed, previous mode will not work after clearing successfully.
2.Choose the Working Mode:
Press and hold the learning button on the receiver, the red light will turn on and stay on for about 5 seconds, then turn off (Clearing Steps), do not release, still hold the learning button, and then the red light will begin to flash, it will flash once, then twice, and finally three times.
(1)After the light flashes ONCE, release the learning button, it becomes Inching Mode.
(2)After the light flashes TWICE, release the learning button, it becomes Self- lock Mode.
(3)After the light flashes THREE times, release the learning button,it becomes Interlocked Mode.

3. Link the remote control:
(After the Working Mode is chosen, you can start to link the remote control according to the mode you choose)
Press the learning button on the receiver until the red light turn on, and then release the learning button, the red light will stay on. Press the button on the transmitter you want to link, and the red light (Signal Light) on the receiver board will flash twice, at this time, it means that the transmitter and receiver finish linking. Then you can press the button on the transmitter, the related receiver will work as the mode you choose.

Note:
1.The receivers in our store are mainly used together with the related transmitter in our company. If you want to use your own transmitter, please confirm if the operating frequency, chip type and vibration resistance of your transmitter are in accordance with ours. If not, they will fail to be linked to. If you want to order the related one,we have unique transmitter as well.

2.How to confirm if the operating frequency, chip type and vibration resistance of your transmitter are in accordance with ours?
Connect power to the receiver board, the power light will turn green, then press your transmitter,if the signal light on the board flash red light,it means your transmitter matech our receiver; if it not flash, it means your transmitter can't be used for our receiver.

3.When you choose the interlock mode,because the quantity of the buttons on the transmittter is the same as the relays, there will be a relay always stay ON, If you want to turn off the last relay, please turn off the power.

The battery required (not supplied) for the remote is 23A 12 Volt.
WARNING: The plastic case is to mounted by an insulated hook or other insulated securing method. Metal hooks and screws will short out the printed circuit board causing failure,not covered by our Warranty.

Package Included:
1 x 12V 10A 4 Ch Wireless remote control switch
1 x Remote controller
1 x Wire
1 x Screw driver
1 x Colorful box