Tron Leg Set
This listing is for:
1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn, Rinzler or Quorra
2) Two pieces of shaped and angled EL Tape to go round the knees
3) Two pieces of sacral shaped EL Panel to go at the lower back
4) Two pieces of 2cm X 25cm EL Tape
4) A Powerful 8 XAA battery EL Driver
4a) choice of power source for this driver:
I) Standard 8xAA Battery Box
II) Rechargable Li-ion Battery (smaller and lighter) with Intelligent Charger (Li-ion Batteries are only available to the UK due to airmail postal restrictions)
5) A 2-way splitter, A 3-way splitter and 2 x 'Short, Medium and Long' Splitter
6) 1.5metres of hook & loop tape - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable
The Set is available in can be any combination of these colours:Orange or Light Blue
The whole kit is ready to use - just plug and play!
Dimensions of the products:
If you are making a costume it is a good idea to plan it out properly.
For this set, the driver/inverter is very powerful and comes with a separate power pack
So here is the dimensions of all the parts plus lengths of wire between them.
Feel free to message me if you have any questions
THE POWER PACK
Takes 8 X AA batteries (not supplied) and is 6.5cm X 6cm X 3cm
it has a 65cm thin power wire coming out of it that leads to the...
DRIVER
The driver is 6cm X 4cm X 4cm
It has the controls on it - Off, Flashing or On
It has a 55cm wire coming out of it that leads to the...
SPLITTER
The Splitter is 40cm long in total,
it is 20cm of wire which then splits into separate strands which are all 20cm long.
A 3-way splitter attaches to the driver
One of these channels has a 2-way splitter attached that runs round the back to clip into the pair of EL Sacral pieces
The other two channels have a special '3 way Small Midi and Long' splitter attached to them that run down each leg
These SML splitters have:
one Short channel that plugs to the 25cm Tape.
Then the Middle channel plugs into the Knee Joint section
The Long channel goes down to the Shin to plug into the Double Hoop
The three pieces of EL Tape that run down the leg are:
1) SHIN
This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any tron costume (these are also available for other parts of your tron costume in our ebay shop)
2) KNEE JOINT
Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes
This has been made to largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you
That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)
3) 2cm x 25cm EL Tape
Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume
Coming off the two way splitter at the back of the costume:
3) EL SACRAL
This pair of pieces sits at the base of the spine and i have to say looks pretty awesome
-
The tape is just 350 microns thick - that is 1/3rd of a millimeter!
Sticky back hook & loop tape is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky
You must sew the other part of the hook & loop tape onto the costume making it very convenient to attach and remove
Of course you don't need to use the hook & loop tape, fix it any way you choose
Its not complicated or fiddly - ive just given all those details if you want to plan your costume before you buy the set - feel free to message me if you have any questions
The whole kit is ready to use - just plug and play!
OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET
A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our ebay store
- - - - - - - - - - - -
This El Tape comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one driver
by using splitters you can also connect different strands to the same driver
VISIT OUR SHOP TO SEE OUR RANGE OF INVERTER/DRIVERS, SPLITTERS AND OTHER EL WIRE