New 2014, 2015 & 2016 EXC 500 450 350 / Enduro Style – Number Plate Carrier (Sub Fender) w/ compact LED Tail/ Stop Light , Flush mount DRC LED Turn Signals , With EE #22-700 License Plate backing combo

DRC #586 Flush Mount turn signals included - (Orange lens color is Standard - Smoke lens color only available if requested at time of purchase)

Plug & Play for KTM EXC 2014, 2015, & 2016 - New Style 4 Pin Connector for Taillight

License Plate Backing- EE License Plate Backing #22-700 included

# 1 This unit is designed for 2014 - 2016 EXC KTM bikes (LED taillight has the new 4 pin connector plug) and is a bolt on, plug and ride product.*

#2 Brand new KTM XC-W (OEM) Sub fender with a New compact LED Tail/ Stop/ Turn Signal / Light with license plate illumination.

# 3 Very compact and durable and saves 6 oz from the stock EXC Sub fender tail/ brake light combo weight

# 4 Complete with KTM Part # U6908818 or EE License Plate Backing Piece –License Plate Backing. Preinstalled – just plug and play

#5 Tail Light tucks in neatly under stock KTM EXC Upper Fender and will be much less likely to be sucked into the rear tire in Extreme Off Road use.

#6 DRC Flush Mount LED Turn Signals with KTM specific Plugs - ready to plug right into your existing OEM EXC harness, (shown on customers bike in pictures 1, 6, & 7).

* If you have a 4 stroke or 2 stroke or XC or XC-W (the ones that have the OEM wiring harness for trail lighting) let me know and we can help you get to where you want to go with your project as we also have taillights, brake light switches and plug in jumpers available.

Please pm or even give a call at 760-828-2625if you have any questions.

Paul Williams

Addititional Notes - 2014, 2015 & 2016 KTM EXC 350 , 450, & 500 :

General installation notes :

I have found it most easily installed by 1st-removing the seat, side panels, and upper fender assembly.
Then Unplug existing taillight wiring and Unplug turn signals. Unseat /unsnap the existing number plate carrier from number plate .
Pre-Install /snap the number plate carrier onto the sub frame.
Re-Connect wiring and verify function.
Install the upper fender, and install bolts that secure the number plate carrier to the sub frame & upper fender assembly.
Re-install side panels, final check of everything then last thing Re-install seat.
Please call me at 760 828 2625
If you have more questions.

KTM in there wisdom has completely integrated the rear turn signal harness, and original license plate light with the entire / complete wire harness.

They are no longer like the 2007 - 2013models which had detachable separate Rear Turn Signal harness, that could be replaced in the event of a crash that damaged the rear taillight and or turn signal wiring , now they are continuously wired through out the complete harness.

I have made plug and play jumpers for the 2014 Turn signal kits for the stock OEM harnesses - this is if you have an undamaged stock harness.

If you have a damaged rear turn signal harness, let me know and I can send out the appropriate parts to help with the adaptation.

The existing Turn Signal connectors once unplugged (you may need to remove the OEM taillight to access the mini connectors) from the OEM turn signals will be reconnected to the Two (2) new small JST connectors attached to the new DRC #586 flush mount LED turn signals .

The Stock license plate light will need to be abandoned - Just trace the white & brown wire up to the connector for the white & heat shrunk bundle for the brown and cut the respective wires approx 3 " from the termination. Then fold over the ends 1" and using either heat shrink tubing or electrical tape secure the fold. Pay attention to the white wire and insure that the bare end is completely covered and cannot short. If one elects the not terminate the separate license plate illumination light, one may fold it back on to itself and secure with either electrical tape or zip tie. Pay extra attention to the brass contacts within the gray rubber bulb mount as they can be inadvertently pressed / forced into each other and cause an elusive wiring short.

Please pm or text or call at760-828-2625 if you have any questions.

Paul Williams