Hendlex CERAMIC SHIELD NC9

HENDLEX Car Body Ceramic Shield NC9 is especially sturdy durable Nano ceramic protective coating designed for cars and motorcycles. This coating can be applied on painted and varnished surfaces and plastics.

The box contains:
• HENDLEX CERAMIC SHIELD (40 ml)
  
• Microfibre Cloth x2 
• Microfibre Applicator 
• Non woven fabric cloth x8 
• Protective Gloves 
• Instruction

Qualities:
• Enhances the hardness of the surface by creating additional protection against minor scratches.
• Smoothens minor scratches; removes the holograms.
• Provides the surface with very strong hydrophobic properties and with the “easy cleaning effect”. The angle of a contact with water is more than 100 degrees therefore the surface remains clean for much longer period of time.
• Significantly highlights the color of paint and provides it with greater shine. Does not attract dust.
• Protects the surface from environmental impacts, such as acids, alkalis (resistant to pH2-pH13), road salts and UV rays. It also protects the surface from aging and provides it with additional protection from corrosion. 
• The coating is resistant to changes of the temperature from -40 °C to 300 °C.

USERS MANUAL

If car is waxed, remove wax using HENDLEX Wax Remover. Wash the car carefully. Make sure there is no washing products (shampoo, dirt solvent) left on the surface. It is recommended to coat polished surface of a car if you want to get a better result. If you have polished the car, make sure to wash it again. Make sure there is no water left in the spaces between the car parts. It is recommended to remove the remaining water using the compressed air jet. It is also recommended to remove dirt and fat using HENDLEX Pain Prepair.

Do not apply the coating in direct sunlight. Proper temperature for coating is from 5 °C to 25 °C. While coating, use the nitrile gloves that are in the set. Hold the applicator by the solid part. Put the application cloth onto the soft part of the applicator (nonwoven fiber cloth). Open the bottle and wet the application cloth in different spots. Cover the surface evenly; make sure that you did not leave uncovered spots. It is recommended to cover the area of 80x80 cm at the time. If the temperature is higher than 25 °C, cover the smaller area. Cover no more than 1 m2 with one nonwoven fiber cloth. The surface must be polished in 20 seconds after coverage because it hardens very quickly. If the surface gets into contact with water, immediately clean it and repeat the coating.

Continue coating areas up to 80x80cm until the full surface of the car is covered. After covering each area, polish it again with micro fiber cloth and make sure there are no unpolished spot left. If there is an unpolished spot and it does not get polished with any effort, use paint polishing paste or 2000 granular sandpaper. Cleaned area must be covered again.

It is recommended to keep the surface in higher than 18 °C temperature for 24 hours and prevent it from getting into contact with water. Depending on the temperature of the environment, the coating fully hardens in 48-72 hours.

 40 ml - 8 m2.

40 ml, 

Photos

Hendlex GLASS PRO 50ml

Properties:
• Long lasting coating (lasts more than 12 months)
• Last up to 3 times longer than common nano coatings
• Does not change color of surface and is completely invisible
• Better visibility during the rain
• Product is environmental and human friendly
• Higher safety on the road 

Hendlex Glass PRO is long lasting hydrophobic coating for glass, which lasts up to 3 times longer than common nano coatings for glass. 

It improves visibility while raining and provides surface strong hydrophobic and easy to clean properties. This product creates an invisible, water-repellent and easily cleaned protective layer, which improves visibility during the rain. Coating makes window cleaning easier from bugs, ice or other dirt.

During the snow or rain, necessity of wipers decreases. Improved visibility increases safety on the road. At speed above 65 km/h, wipers are almost unnecessary. In winter, the ice is removed from windows much faster and easier. Hendlex Glass PRO coating is suitable for all car windows. This product is also suitable for trucks, busses and motorcycles.

Properties:
• Long lasting coating (lasts more than 12 months)
• Last up to 3 times longer than common nano coatings
• Does not change color of surface and is completely invisible
• Better visibility during the rain
• Product is environmental and human friendly
• Higher safety on the road 

surface has to be clean, dry and oil, grease free. If glass is waxed, clean it with Hendlex Wax Remover and wash with water. It is recommended to clean glass with Hendlex paint prepare before coating.

using special application cloth buff coating into the surface. Repeat buffing process several times without using additional coating. Wait for 5 minutes and polish the surface with cloth. Application temperature should be more than +5⁰C. Protect surface for 4 hours from water.

do not apply coating on direct sunlight. Keep container well closed. Use in well ventilated area. Keep out of reach of children.

50 ml covers up to 10 m2 surface area.

50 ml

Photos

HENDLEX GLASS INVISIBLE WIPERS 50ML

Qualities:
• The coating is long lasting effect (will last more then 12 months on rear and side glass,  windscreen  last more then 6 months)
• At speed above 65 km/h, wipers are almost unnecessary
• Nano particle coating creates an additional protection against mechanical scratches
• Protective coating is non-slippery and invisible
• Product is environmental and human friendly
• Easy to use

It is hydrophobic coating for car windows. It improves visibility of the road while raining and provides the surface with strong hydrophobic qualities. This product creates an invisible, water-repellent and easily cleaned protective layer, which improves visibility in the rain or during the night. The coating will ease window cleaning from bugs, ice or other dirt. During the snow or rain, necessity of wipers decreases. Improved visibility increases safety on the road. At speed above 65 km/h, wipers are almost unnecessary. In winter, the ice is removed from the window much faster and easier. Hendlex Nano coating for car windows is suitable for all car windows. For its hydrophobic (water repellent) coating qualities, coated front, side and rare windows, improve visibility, especially at night. This product is not only for cars, but also for trucks and motorcycles.

the surface has to be clean, dry and oil, greese free. Apply using special Baltic Nano Technoogies application cloth or aplicator, buff in the surface, leave for 5 minutes and then polish with a microfiber cloth. Application temperature above +5⁰C.

Temperature must be +5⁰C - +40⁰C when coating. Keep Container always well shut. Use in a  well ventilated area. Keep out of reach of children.

50 ml covers up to 10 m2 surface area.

50 ml

Together with product there is special non-woven fiber cloth, for coating aplication.

Photos

Hendlex Nano CERAMIC SHIELD NC9 200ml

HENDLEX Car Body Ceramic Shield NC9 is especially sturdy durable Nano ceramic protective coating designed for cars and motorcycles. This coating can be applied on painted and varnished surfaces and plastics.

Qualities::
• Enhances the hardness of the surface by creating additional protection against minor scratches.
• Smoothens minor scratches; removes the holograms.
• Provides the surface with very strong hydrophobic properties and with the “easy cleaning effect”. The angle of a contact with water is more than 100 degrees therefore the surface remains clean for much longer period of time.
• Significantly highlights the color of paint and provides it with greater shine. Does not attract dust.
• Protects the surface from environmental impacts, such as acids, alkalis (resistant to pH2-pH13), road salts and UV rays. It also protects the surface from aging and provides it with additional protection from corrosion. 
• The coating is resistant to changes of the temperature from -40 °C to 300 °C.

USERS MANUAL

If car is waxed, remove wax using HENDLEX Wax Remover. Wash the car carefully. Make sure there is no washing products (shampoo, dirt solvent) left on the surface. It is recommended to coat polished surface of a car if you want to get a better result. If you have polished the car, make sure to wash it again. Make sure there is no water left in the spaces between the car parts. It is recommended to remove the remaining water using the compressed air jet. It is also recommended to remove dirt and fat using HENDLEX Pain Prepair.

Do not apply the coating in direct sunlight. Proper temperature for coating is from 5 °C to 25 °C. While coating, use the nitrile gloves that are in the set. Hold the applicator by the solid part. Put the application cloth onto the soft part of the applicator (nonwoven fiber cloth). Open the bottle and wet the application cloth in different spots. Cover the surface evenly; make sure that you did not leave uncovered spots. It is recommended to cover the area of 80x80 cm at the time. If the temperature is higher than 25 °C, cover the smaller area. Cover no more than 1 m2 with one nonwoven fiber cloth. The surface must be polished in 20 seconds after coverage because it hardens very quickly. If the surface gets into contact with water, immediately clean it and repeat the coating.

Continue coating areas up to 80x80cm until the full surface of the car is covered. After covering each area, polish it again with micro fiber cloth and make sure there are no unpolished spot left. If there is an unpolished spot and it does not get polished with any effort, use paint polishing paste or 2000 granular sandpaper. Cleaned area must be covered again.

It is recommended to keep the surface in higher than 18 °C temperature for 24 hours and prevent it from getting into contact with water. Depending on the temperature of the environment, the coating fully hardens in 48-72 hours.

Photos

Hendlex GLASS and CERAMIC 100ml

Qualities:
• Hydrophobic coating  lasting  up to 2 years
• Durable protection of coated surface from moisture, dirt and grease
• Coated surface is easily cleaned with damp cloth
• Nano-particle coating adds additional protection against mechanical scratches
• Does not change the color of the surface and is completely invisible
• Preventive protection against bacteria, algae, mold and lime scale 

It is a hydrophobic coating for glass and ceramic surfaces. This coating facilitates dirt and lime treatment.

Nanotechnology coating is designed for care of ceramic:
• sinks;
• tubs;
• showers;
• glazed ceramic tiles;
• glass products;

After applying the surface with this product, hydrophobic (water-repellent) Nano-particle coating is formed. It facilitates cleaning of various kinds of dirt, lime and soap precipitates. There is no need to use chemical measures for cleaning surfaces. It will be easily cleaned with a damp cloth and less time will be wasted for care of surfaces.

This product prevents from reproduction of micro-organisms that are dangerous for health. Dirt does not stick to protective coating of Nano-particles; therefore you do not waste time cleaning the spaces between the tiles. This product is not harmful to the environment.

Glazed ceramic tiles. - The coating protects the tiles and spaces between them from formation of lime, soap and other dirt. Tiles become easy to wash off with water; there is no need to use additional expensive cleaning products. Protective coating is non-slippery and invisible.

Ceramic sinks - Dirt spoils the surrounding view as well as it is a place where dangerous bacteria concentrate. With a help of Hendlex surface protection product, formed Nano-particle coating prevents from dirt sticking to the surface.

Shower cabins - Coated with Hendlex product, walls of shower cabins become easy to maintain. The lime, soap precipitate is easily cleaned with a damp cloth, and thus significantly reduces the use of conventional cleaning. Furthermore, the surface remains clean without much effort. The resulting Nano-particle coating is a preventive protection against mold formation.

Refrigerators - Interior coated with Hendlex product is easily cleaned, protected from the formation of mold and from unpleasant odours. 

the surface must be completely clean, dry and grease free. Use special Baltic Nano Technoogies application cloth or aplicator to apply coating to surface by polishing in applying light pressure, wait 5 minutes and polish. When applying indoor temperatures must be not lower than +5°C degrees.

Application temperature is + 5°C + 40°C. Keep container tightly closed. Use in a well ventilated area.

100 ml will cover up to 20 m2 depending on surface.

100 ml

Photos

Hendlex PAINT PREPARE 200ml

Hendlex paint prepare is concentrated cleaner, used to prepare surface before using nano coatings. Cleaner removes fat and cleans surface. It is suitable for all not wetting surfaces.

Properties:
• concentrated cleaner
• removes fat and cleans surface

spray Hendlex Paint Prepare on surface and wipe it with microfiber towel. Wait until the surface gets dry. Do not dilute.

TKeep container well closed. Keep out of reach of children. Use in a  well ventilated area.

200 ml for 40 m2

200 ml

Photos

Hendlex PLASTIC AND METAL 50ml

It is hydrophobic coating for plastic and metal. Repels water and grease. Surface provides easy cleaning effect.

Qualities:
• repels water and grease
• the coating is long lasting effect
• protective coating is non-slippery and invisible

the surface has to be clean, dry and oil, greese free. Apply using special Baltic Nano Technoogies application cloth or aplicator, buff in the surface, leave for 5 minutes and then polish with a microfiber cloth. Application temperature above +5⁰C.

Temperature must be +5⁰C - +40⁰C when coating. Keep Container always well shut. Use in a  well ventilated area. Keep out of reach of children.

50 ml covers up to 10 m2 surface area

50 ml

Together with product there is special non-woven fiber cloth, for coating aplication.

Photos

Hendlex SHOES PROTECT suede leather, 100ml 

Nano impregnator for suede leather makes surface water and fat repellent.  Coating very well suits for impregnating footwear and protecting it from any dirt. Impregnated surface remains air breathable. Coating does not change color of surface.

Qualities:
• protects the surface from fluid and oil penetration
• it does not contain silicone, so the coated surface appears dull and does not have wet surface effect
• the product is odourless
• no volatile organic compounds

Surface must be completely clean, dry and free from grease or oil. Spray evenly on the surface, until surface gets wet.  Wait until surface will get dry.

 Application temperature is + 5°C + 40°C. Keep container tightly closed.

100 ml for 2-5 pairs of shoes.

100 ml

Together with product there is special non-woven fiber cloth, for coating aplication.

Photos

Hendlex WAX REMOVER 200ml

Hendlex Wax Remover is used for removing wax from surface. Cleaner effectively cleans surface from wax and it’s residues without damaging surface.

spray Hendlex Wax Remover on surface and wipe it with microfiber towel. Rinse surface with water and clean with Hendlex Paint Prepair. Wait until surface gets dry. Surface is prepared for coating with nano coatings.

Keep container well closed. Keep out of reach of children. Use in a  well ventilated area. Protect from freezing.

200 ml for 25 m2

200 ml

Photos

Hendlex CABRIO PROTECT 200 ml

Nanotechnology impregnator for textiles makes fabric resistant to liquids and fat. 

Qualities:
• protects the surface from fluid and oil penetration
• the surface remains breathable
• it does not change the surface color
• it does not contain silicone, so the coated surface appears dull and does not have wet surface effect
• long lasting efect
• no volatile organic compounds

the surface must be completely clean, dry and free from grease or oil. Shake well and spray evenly distributed on the surface. Wait until surface will get dry.

Once the product has been applied for 4 hours the surface should not come into contact with water. Suitable coating temperature +5°C - +40°C. Do not use it in a higher or lower temperature! Keep container tightly closed. Keep Container protected from direct sunlight and frost.

the 200 ml can cover 2-5 m2 depending on the surface.

200 ml

Photos

Hendlex LEATHER coating, 100ml/200ml

Nano coating for leather, is designed to protect the surface, refreshes the color, softens the skin and gives a hydrophobic effect and protects against moisture and dirt. The coating renews the surface and gives a natural shine. Nano coating is suitable for car leather seats.

Qualities:
• Nano coating refresh the surface and gives a natural shine
• Provides water repellency
• Reliably protects leather surfaces against moisture and dirt
• Resistant to temperature changes

the surface must be completely clean, dry and grease free. Shake well before using. Use special Baltic Nano Technoogies application cloth or aplicator to gently buff in the surface and wait until dry. Indoor temperatures should be not below + 5°C temperature.

Application temperature is + 5°C + 40°C. Keep container tightly closed.

the 100 ml can cover 5-10 m2 depending on surface.

100 ml

Together with product there is special non-woven fiber cloth, for coating aplication.

Photos

Hendlex TEXTILE for textiles and footwear, 200 ml

PROTECTION FROM STAINS AND WATER

Qualities:
• protects the surface from fluid and oil penetration 
• the surface remains breathable
• it does not change the surface color
• it does not contain silicone, so the coated surface appears dull and does not have wet surface effect
• no volatile organic compounds.

Nanotechnology impregnator for textiles makes fabric resistant to liquids and fat. It prevents the surface of the fabric from various stains.

The product is ideal for:
• textile;
• wool;
• canvas products;
• soft furnishings;
• rugs;
• coats (not suitable for syntheticproducts).

Hendlex product creates invisible protective and tight layer from water and dirt.

Covered with this product, surface stays clean for a long time: coffee, grease, water stains do not soak into the Nano-protected surface, they are easy to clean using cloth. The surface becomes resistant to liquids and, at the same time, remains air - permeable. There is no trace of the product on the covered surface; fabric does not change its color; the product has no smell. It is a great help for people who raise children, have pets, want to protect light-colored furniture and prevent it from stains.

the surface must be completely clean, dry and free from grease or oil. Shake well and spray evenly distributed on the surface. Wait until surface will get dry.

Once the product has been applied for 4 hours the surface should not come into contact with water. Suitable coating temperature +5°C - +40°C. Do not use it in a higher or lower temperature! Keep container tightly closed. Keep Container protected from direct sunlight and frost.

the 200 ml can cover 2-5 m2 depending on the surface.

200 ml

Photos