WIND TURBINE, COMES IN 12 VOLT 3 PHASE AC TO DC OUTPUT MODEL

(Can be used as 3 phase output or Dc output for battery charging)

3 phase output is the most efficient; no voltage and amperage loss in long runs

like DC suffers from. DC output requires heavy expensive cable

and has a high power loss over long runs. Straight DC

output is now just simply old technology. If you are replacing a dc output model  you can

just mount the  included bridge rectifier at the top of the tower

for the same run of  wire as your DC model if you wish. The bridge rectifier converts the long run of efficient

3 phase into dc next your charge controller, batteries, or grid tie inverter. The 3 phase output can

be used direct to some equipment like 3 phase grid tie inverters as well. Either way you use

it this is a very versatile output wind turbine. 

90 amp 3 wire slip ring

3-Phase brake switch with short circuit brake

Also for use with DC output wind turbines

50 amp, 3-phase switch with short circuit brake works with 12 volt to 250 volt systems. Designed for 1500 watt and smaller turbines.

Simple, yet perfect for small turbine installations, this 3-phase switch uses a specialized switch to provide both disconnect capability as well as braking by shorting out the 3 wires of the stator. Although designed specifically for 3-phase turbines it works equally well for single phase AC turbines as well as DC turbines.

Switch Positions:

This switch will handle 2500 watts continuously.

Rated at:

Yaw Bearing for 1 1/2 Inch Diameter Wind Turbine Towers (fits pipe with 1 7/8" OD)

(Yaw bearing is 1 15/16" inside diameter)

 

Freedom 5 blade 12 volt wind turbine

  

• Freedom PMG (PERMANENT MAGNET GENERATOR) WITH 14 MAGNET ROTOR.
• One heavy duty bridge rectifier for converting 3 phase to dc output. 
• Mounting Bracket and Heavy Duty 2 arms tail assembly. Hot dipped galvanized!
• Tail fin measures 29" tall for maximum tracking. 
• No slip rings to fail or replace. Wire tension system.
• Comes with 5 nylon carbon fiber composite blades. 
• Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades ™ for maximum output.
• Steel blade hub is 3/16" x 6 1/2" Zinc plated.
• Blades Make  61" dia.  
• Mounting Bracket Fits on 1.5" schedule #40 or #80 pipe.
• 125,000 hours + of rated bearing life.
• Freedom PMG has no brushes, Stainless steel rotor shaft, very dependable!  
• Heavy duty Hub spacer/stabilizer 
• Wind Turbine weighs 49 lbs.  
• 3 YEAR Limited  WARRANTY. 
• box size 30" x 10" x 8"

Our Freedom PMG™ permanent magnet generator is specifically 

designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).  

Why buy a Freedom or Freedom PMG™ over a Delco car alternator PMA?

The answer is simple:

The answer is simply the Freedom PMG was designed for wind turbine use and more copper!

More copper in the stator core equals more power.  

Each Freedom PMG™ rotor contains twice as much copper than any Delco style PMA.

PMG Features: 

• Comes with one heavy duty rectifier & one hub spacer stabilizer
• 17 mm Stainless steel shaft
• Polished aluminum case
• Zinc plated 14 magnet rotor and skewed stater core
• For charging 12 volt battery banks
  
• Specifically designed for wind turbines.

PMG Specifications:

• 3/8" diameter bolt holes
• 1 15/16" on center between mounting holes
• 5 7/8" OD width
• 6 5/16" tall

WE BELIEVE IN THE QUALITY OF OUR RAPTOR GENERATION 4 ™ WIND

TURBINE BLADES SO MUCH WE'RE NOW GIVING A

LIFETIME WARRANTY AGAINST THEM BREAKING

FOR ANY REASON! (see details below) FREE REPLACEMENT!

For ALL UPS orders, we only ship signature required!! Contact us right away if you need to make other arrangements!