RB 150 Amp 1/8^th scale Buggy / Truck 2-6S ESC RB02011-010 

This brushless, sensorless speed control is packed with many features making it unbeatable for either non stop fun or top level racing!

RRP £85

ESC Modes: Fwd/Brk or Fwd/Brk/Rev

Input Power (Cells): 2-6S LiPo

Motor Limits:

Brushless KV ≤ 2400 Up to 6S(25.2Volt), for 1/8 monster trucks and truggies

Brushless KV > 2400 Up to 4S(16.8Volt), ideal for 1/8 buggies

Resistance: 0.0002 Ohms per phase at 25 °C (77 °F) Trans. Temp

Continuous/Burst Current: 150 Amp / 950 Amp

Switching BEC: 5.7 Volts, 3 Amp

Status LED: 1 with 3 color (Red, Green & Orange)

Thermal Overload Protection: Yes

Dimensions(LxWxH): 48.8x57.8x35.8mm (1.29x2.28x1.41in) 

Weight (Without wires): 88g (3.1oz)

The ESC must be calibrated on first use or whenever it is to be used with a different transmitter

● How to Calibrate ESC:

- ESC switch OFF.

- Turn on the Transmitter.

- Hold full throttle on your transmitter and turn the ESC's switch ON.

- Keep holding full throttle on the transmitter. The ESC will flash LED and ring the initialisation tones.

- Wait 2 seconds

- Green LED blinks rapidly and the motor will ring 4 times indicating full throttle measured.

- Red LED blinks whiles beeping, indicating it's time to push full brake. Move throttle trigger to full brake and wait a few seconds, the ESC will blink red

LED and ring 4 times indicating full brake measured.

- Yellow LED blinks while beeping, indicating it's time for neutral. Relax trigger to neutral (centre). The ESC will now ring 4 times and flash the yellow

LED rapidly to accept the neutral position.

- ESC will blink LED and ring twice indicating that it is armed.

Programming your ESC: 

Programming the ESC is as simple as answering a few questions. The ESC asks questions by beeping a setting number,

followed by the possible setting values. There are nine settings that can be programmed in the brushless ESC.

- Plug Battery into the ESC

- Hold full throttle on your transmitter

- Turn the ESC switch ON

- ESC flashes LED and rings once

- Wait few seconds.

- ESC flashes LED and rings 4 times indicating that it is ready for

CALIBRATION mode

- Continue to hold full throttle

- ESC flashes LED while beeping

- Wait another few seconds

- ESC flashes LED and rings 4 times

-ESC flashes LED while beeping indicating that you are in

PROGRAMMING mode

-        Let trigger go neutral (Centre)

● At this point the ESC will be flashing/beeping the following sequence:

Beep-Pause-Beep... and then repeats

This indicates that you are at Question 1 and it is asking to accept/reject value 1.

● When answering a question, you will need to move the trigger to yes (full throttle) position or no (full brake) position and keep it there for

about 3 seconds. When the ESC has accepted your answer it will confirm your reply by flashing the LED and emitting a beeping tone. Release the

trigger allowing it to go to Neutral to confirm that you are ready for ESC to ask you the next question. You are not required to continue through all nine

programming options. For example, if you wish only to change the Brake/Reverse Type (Option 1) then after programming that setting you can

disconnect the power from the ESC and you're ready to run. Disconnecting the controller in the middle of programming simply retains the values for the

remaining programming options that were previously set up.

SAFETY NOTE

WARNING: This is an extremely powerful brushless system. We

strongly recommend removing your pinion gear for your own safety

and the safety of those around you before performing calibration and

programming functions with this system. Please keep your hands,

hair, clothing etc. clear from the gear train and wheels of an armed high

performance system.

- WATER & ELECTRONICS DON'T MIX!

Never allow water, moisture, or other foreign materials to get inside

ESC, motor, or on the PC Boards. Water damage will void the warranty!

- NO REVERSE VOLTAGE!

Reverse battery polarity can damage ESC & void warranty. Disconnect

battery immediately if a reverse connection occurs.

- DISCONNECT BATTERIES WHEN NOT IN USE

Always disconnect the battery pack from the speed control when not in

use to avoid short circuits and possible fire hazard.

- 2 - 6 LI-PO CELLS ONLY

Never use fewer than 2 or more than 6 LIPO cells in the vehicle's main

battery pack. The brushless ESC handles up to 6S LIPO input (25.2

Volts MAX).

- TRANSMITTER ON FIRST

Turn on the transmitter first THEN turn on the speed control.

- INSULATE WIRES

Always insulate exposed wiring with heat shrink tubing or electrical tape

to prevent short circuits, which can damage ESC.

- 1/8 SCALE OR SMALLER

The brushless ESC is intended for 1/8 scale vehicles.

# 101713 - Flux Scream 1:8th scale 1965 KV Brushless Motor
1965 RPM/VOLT / USE WITH FLUX RAGE ESC

The Flux Scream is the perfect match for any 1/8th scale electric buggy or truggy! 

With 1965Kv on tap, this massive brushless motor gives jaw-dropping acceleration and blinding top speeds! Match it with the #101712 Flux Rage 1:8th scale 80Amp Brushless ESC for a perfect blend of grunt and all-out speed with twin 2S power for up to 14.4 volts of juice!

Shaft Diameter - 5mm 
Diameter - 42mm 
Length - 68mm (without shaft) 
Shaft length - 18.5mm 
Weight - 345g 
Connector - 6mm Bullet
Machined aluminum casing
Ball bearing supported shaft

PBM Racing has been Established for over 25 years!

PBM Racing is one of the UK's leading suppliers of Radio Control Cars and other RC Vehicles. You are very welcome come to view and buy the products we supply together with a vast range of spares and accessories, in our shop at: 54 Valley Drive, Newthorpe, Nottingham, NG16 2DT, United Kingdom. We use eBay to showcase a selection of our most popular items.  Please feel free to get in touch we’re always happy to provide free and impartial advice to help you get the best out of your RC experience!

"RC products make great gifts any time of the year, and we are confident we can send you on your way with exactly what you need and nothing else!"

 For more Information call us at the shop on 01773 769323 

or email sales@pbmracing.co.uk

Store opening Hours: 

Monday 9.30am-7pm

Tuesday 9.30am-5pm

Wednesday 9.30am-5pm

Thursday 9.30am-5pm

Friday 9.30am-5pm

Saturday 9.30am-5pm

***Express delivery orders placed before 2 pm will be processed same day, orders placed after 2pm will be processed next day***