35W/55W HID Xenon Headlight Conversion KIT H1/H3/H4/H7/H11/9005/9006/880/881/D1S
DescriptionProduct description
So, you must include the following info in PayPal's "Note To Seller" section or send us an email or eBay message: →Bulb Type
1. You can keep a regular halogen for the high beams and install hid lights for the low beam only 2. Or you can use bi-xenon HID headlights with one dual xenon bulb for both high and low beams We are proud to offer the most durable bi-xenon HID headlight kits, check them out. Available Bulb Types: H4-Bixenon (9003/HB2), 9004-Bixenon, 9007-Bixenon and H13-Bixenon (9008) A Bi-Xenon bulb replaces a H4 halogen bulb that produces low beam as well as high beam. A H4 halogen bulb has therefore two filaments, one for low beam and one for high beam. The Bi-Xenon bulb however, only has one 'light cell'.(See The Pic. Below) By means of an ingenious electro-magnetic construction, this light cell can change position. One position is low beam, the other is high beam.
Slim Ballasts use smaller internal components and still offer the same input and output power as its standard sized version. With the Igniter unit in an epoxy filled chamber, we are able to reduce the size of the core unit by roughly half, also reducing the weight significantly. Slim Ballasts are easier to mount, weigh less, and allow users to install their HID systems faster with less time spent under the hood, and more time enjoying their HID lights!
The color of light is measured and expressed in degrees Kelvin (K). The color spectrum ranges from a red to purple. HID headlamps do not have this wide of a range though there are different bulbs that skew toward either extreme. Most are more focused on the center of that range. 4,300K is the temperature that is closest to natural daylight. Factory HID headlamps are setup for this color temperature. Conventional Halogen filament bulbs are yellowish which is equivalent to a 3,300K temperature. 6,000K has a bluish tint and temperatures above that are increasingly blue shifting to a purple tint. Color Temperatures Available: 3000k,4300k,5000k,6000k,8000k,10000k,12000k,15000k,30000k The higher the temperature the more blue is in the color of the bulb.
The 35W HID kits use 35W of power to produce HID light. The 55W use more power to produce more light. The 55W HID kits cost generally more than the 35W HID kits. This is a question of personal choice. If you need maximum light output, if you drive on very dark roads, you will want to install a 55W HID kits for more lighting power.
This kit contains everything you need to upgrade your existing car's headlight system to the best lighting available today! 1) Single Beam Hid Conversion Kit Includes: ( With Original Box ) 2x Xenon HID Bulbs 2x Digital Slim HID Ballasts ( Single Beam don't need the relay harness ) 2) Dual Beam Hid Conversion Kit Includes: ( With Original Box ) 2x Xenon HID Bulbs 2x Digital Slim HID Ballasts All Necessary Wiring and Connector Bulb Sizes and Color Temperatures Available Bulb Sizes Available: H1、H3、H7、H8、H9、H10、H11、9005/HB3、9006/HB4、880、881< /span> H4-H/L ,9004-H/L,9007-H/L,H13-H/L Color Temperatures Available: 3000k,4300k,5000k,6000k,8000k,10000k,12000k,15000k,30000k Ballast Wattage: 35W / 55W
Please read this guide before attempting installation. By reading the steps outlined you will be more prepared for the installation reducing possible errors and problems. Contact us if you have any trouble. Common Tips:
Common Problem:
Parts included with your kit:
Step 1: Open hood and locate the factory light bulb you are trying to convert. If fog lights, you may need to pull out your factory fog light housing to access the back. On some vehicles you can access factory bulbs from the engine bay or from the wheel wells with your wheels fully turned on direction. Please consult your owners manual or dealer on how to access your factory light bulbs. In 90% your bulbs are easily removed without too much trouble. Once your factory light bulb is removed, you can prepare for the HID bulb insertion. Step 2: Remove the plastic capsule preinstalled on the HID bulb and insert into your headlight socket. HID bulbs should fit similar to your factory light bulb, but the tolerances may be slightly different on certain vehicle models. Bulb installation will vary from twisting to clamping from the back depending on the bulb type. Be very gentle with the HID glass portion. Do not touch the glass with your fingers. If it does end up getting dirty, simply wipe with clean cloth gently. Notice: Some vehicle models may require adapters for the bulb to fit into the socket. These include H7 bulbs. Some parts off of your original headlight may be be required depending on car model. Example, 9007 light bulbs will require the reinstallation of the plastic bulb holder adapter. Some BMW/VW/Mercedes/Saab will require a metal adapter or plastic adapter to hold the bulb in place. Step 3a: Once the HID bulb is fixed into place locate the factory connector where the original halogen bulb was connected to. You will now connect the supplied wire (may be a plug or 2 metal tips) that you must insert into your factory connector as shown below. When we say factory connector, this is the connector your original bulb was feed power with. If you purchased a Bi-xenon kit, or a kit with relay, your installation will be a little different than above. See steps 3b or 3c. Step 3b: If your kit included a relay you will not use the provided extra wires shown in Step 3a. that connect ballast to factory headlight plug. Instead the ballast get connected to the relay as shown below. The relay then will connect to your factory headlight plug. Some relays will have two plugs one for each side, while others only one headlight plug. Remember a relay simply gets a signal from your headlight plug, then allows power to flow directly from your battery. Step 3c: If your kit purchased is a bi-xenon kit also known as hi/low (low beam + high beam HID with movement). This only applies to kits with bulb types 9004 9007 H4 H13 9008. Notice on these kits there will be only 1 headlight plug connector. One of your headlight connectors may not be used. Step 4: Before mounting ballast permanently please test the system. Low beam, high beam and fog light function if it applies to your install. It is best to turn the vehicle on to test the system as some vehicles do not give full voltage when vehicle is running only from battery. Step 5: Mount the ballasts on any existing bolt or flat surface away from excessive heat. We do not recommend mounting on top of the radiator or in front or behind it. Ballasts are electronic devices which excessive heat can ruin. Make certain the wires with your kit cannot get tangled into the belt line or are resting on very hot components of the engine. PaymentShippingFeedback.We suggest our buyer to leave feedback after the item received. After we receive buyer's positive feedback, we will leave positive feedback to the buyer at the same time. Return policyWe are not responsible for any custom duty or import tax.
The item is sold on an "as is" basis, please ask all questions before bidding to avoid getting an item you are not satisfied with.
We want our customers to feel safe knowing they can return their items,no questions asked! If you are not happy with your items for any reason, simply follow these 3 easy steps!
1. Email us to get the return mailing address
2. Write down 'RETURN' clearly on the envelop and return to the address provided.
3. Buyers will be contacted to arrange refund of merchant value once the returned item is received. Please note that postage is NOT refundable.
Returns Restrictions:
1) All returns must be postmarked within 3 days of receipt of your package.
2) If items are damaged, we must be contacted within 24 hours of receipt. We will not accept any items with odors (perfume, smoke, etc.)
3) All original tags must be attached, with no signs of wear. Contact us |