This is one pair (2 pieces) Brand New KRELL EVOLUTION 602E MONO POWER AMPLIFIER, EACH AMPLIFIER 600W . MADE IN THE USA.
Mono Amplifier
The Evolution 600e monaural amplifier sits in the middle of the
Evolution e Series. Powerful enough for almost any application, the
Evolution 600e is the amplifier choice in many stereo and home theater
systems worldwide. This power capability is coupled to a new green
operating mode that reduces standby electrical draw to a mere 2 Watts.
As with all Evolution amplifiers, the Evolution 600e development began
with a question, "What is the most difficult scenario this amplifier
will face?" The answer is a 2 Ohm speaker load. When the final design is
complete, and the amplifier is presented with a typical 8 Ohm speaker,
it practically coasts. This amplifier simply sings with this stress-free
load connected. Outputting a daunting 600 watts of power and coupled to
Krell Evolution e Series circuit technology, the Evolution 600e is a
velvet hammer.
The Evolution 600e is equipped 2 2,200 VA transformers and 108,000 μF. This power source is the backbone for the output of the Evolution 600e. With this foundation, the Evolution 600e delivers 600 watts into 8 Ohms, 1,200 watts into 4 Ohms, and 2,400 watts into 2 Ohms. The FTC mandates that power ratings are quoted using a 1,000 Hz sine wave into a fixed 8 Ohm resistor with final power specification stated at 1% distortion. Krell engineering considers this specification too lenient and not indicative of what an amplifier is required to provide. Krell designs to a much stricter standard. Our power tests use a 20-20,000Hz signal into 8, 4, and 2 Ohm loads with our final specifications stated for .1% distortion.
Evolution 600e Frequency Response 20 Hz to 20 kHz +0, -0.18 dB <0.5 Hz to 120 kHz +0, -3 dB
Signal to Noise Ratio >110 dB, wide band, unweighted, referred to full power output >119 dB, "A"-weighted
Gain 25.4 dB
Total Harmonic Distortion <0.02% at 1 kHz, at 600 W, 8 Ohms <0.15% at 20 kHz, at 600 W, 8 Ohms
Input Impedance Single Ended: 100 kOhms Balanced: 200 kOhms CAST: 70 Ohms
Input Sensitivity Single Ended or Balanced: 3.72 V rms CAST: 3.72 mA rms
Output Power 600 W RMS at 8 Ohms 1200 W RMS at 4 Ohms Output Voltage 196 V peak-to-peak 69 V RMS
Output Current 49 A peak
Slew Rate 100 V/µs
Output Impedance <0.030 Ohms, 20 Hz to 20 kHz
Damping Factor (referred to 8 ohms) >270, 20 Hz to 20 kHz
Transformer Two 2200 VA (4400 VA total) for audio circuitry One 10 VA for digital control circuitry
Power Supply Capacitance 108,000 µF
Power Consumption Standby: 2 W (High-current standby: 260W) Idle: 410 W Maximum: 3800 W Heat Output Stand-by: 7 BTU/hr. (High-current standby: 890 BTU/hr. Idle: 1400 BTU/hr. Maximum: 5500 BTU/hr.
Inputs 1 single-ended via RCA connector 1 balanced via XLR connector 1 CAST via 4-pin bayonet connector
Outputs 1 pairs Krell binding posts
Dimensions 17.3 in. W x 9.8 in. H x 22.1 in. D 438 mm W x 248 mm H x 560 mm D
Weight Shipped: 150 lb., 67.9 kg Unit Only: 135 lb., 61.1 kg |