8 VOLT 150 TO 300 MA RAW 8.5MM LED REPLACEMENT FOR PIONEER SANSUI KENWOOD OTHERS . 

USED IN KENWOOD 6600,7600,9600,8005,9940,OTHERS.                                 

 THIS STYLE STANLEY RUBBER BASE BULB PUSH FITS OVER 2 PINS AS SHOWN IN PICTURES. PIN SPACING IS 13 TO 14 MM CENTER TO CENTER(SLIGHTLY OVER 1/2 INCH). THESE LONG LASTING  HIGH OUTPUT (100,000 TO 140,000 MCD @ 100 MA) 8.5MM  LED CIRCUIT RAW REPLACEMENTS HAVE AN AVERAGE LIFESPAN OF 100,000 HRS.THE AVERAGE INCANDESCENT BULB LIFESPAN IS 1000 HRS. REINSTALL INTO EXISTING LAMP BASE USING A PAIR OF NEEDLE NOSE PLIERS. CIRCUIT REGULATION BUILT INTO LED LEADS.  LED INCORPORATES 5 SEPARATE CHIPS AND DRAWS AROUND 50 MA. LED LEADS CAN BE BENT TO MAKE A 90 DEGREE LAMP USED IN SANSUI TU417,TU517,TU707,TU717,TU-5900,TU-7900,TU-9900.  THESE WIDE DISPERSION STRAW HAT LED BULBS ARE AVAILABLE IN WHITE (140K MCD), WARM WHITE(40 lm), BLUE(180K MCD) , GREEN(100K MCD), RED(100MCD), AND ULTRA-VIOLET(30K MCD). SEE PICS. AS ALWAYS, THANKS FOR LOOKING.

NOTE: PRICE APPLIES TO ONE RAW 8 VOLT AC LED REPLACEMENT BULB TO BE USED IN YOUR RECYCLED  STANLEY RUBBER BASE. PLEASE SPECIFY COLOR  ON ORDER OR BY E-MAIL TO AVOID DELIVERY DELAY. I WILL NOT ASSEMBLE OR SHIP WITHOUT THIS INFORMATION. 


Lamp Information

Harman/Kardon Citation 18
The very small bulb that lights the "In Tune" indicator and the "Stereo" indicator is a 12 volt 35 milliamp type

Kenwood 600T and 650T

8 volt 300 milliamp X 5 bulbs (two for dial and one for each of the meters) X 5 green-tinted bulbs with rubber grommet base and wire leads Kenwood 600T and 650Tfor dial and one for each of the meters)

Kenwood KR-5400
Meters and dial use 8 volt 200 milliamp X 5 bulbs with rubber grommet base and wire leads.

Kenwood KR-7600 receiver
Dial uses 8 volt 300 milliamp X 6 bulbs with rubber base that push over two pins, same as the Sansui TU-717. Meters use 8 volt 200 milliamp X 4 frosted bulbs with rubber grommet base and wire leads. Button indicator lamps - 8 volt 50 milliamp t1.75 grain of wheat bulbs.

Kenwood KR-9600 receiver
Dial uses 8 volt 300 milliamp X 6 bulbs with rubber base that push over two pins, same as the Sansui TU-717. Meters use 8 volt 200 milliamp X 4 frosted bulbs with rubber grommet base and wire leads. Button indicator lamps - 8 volt 50 milliamp t1.75 grain of wheat bulbs.

Kenwood KR-x500 and KR-x600 receivers

8 volt 200 milliamp bulbs with rubber grommet base and wire leads, and 8 volt 300 milliamp bulbs with rubber base that push over two pins.

Kenwood KT-80
8 volt 50 milliamp X 1 (power switch cap)

Kenwood KT-615
8 volt 50 milliamp X 1 (stereo indicator)
12 volt 150 milliamp X 2 - Physically the same as those used in the KT-815 (8 volt 300 milliamp).

Kenwood KT-815 and KT-8155
Dial and Meters use 8 volt 300 milliamp X 4 green-tinted bulbs with rubber grommet base and wire leads.

Kenwood KT-917
8 volt 300 milliamp X 5 identical to those in the 600T.

Kenwood KT-1000
8 volt 150 milliamp X 1
8 volt 50 milliamp X 2 (stereo and lock indicators)

Kenwood KT-5500
8 volt 300 milliamp X 2 green-tinted bulbs with rubber grommet base and wire leads - one for dial and one for meters.

Kenwood KT-6005 and KT-6007
Dial uses 8 volt 300 X 4 milliamp bulbs with rubber base that push over two pins, same as the Sansui TU-717.

Kenwood KT-6500 and KT-6550
8 volt 300 milliamp X 3 green-tinted bulbs with rubber grommet base and wire leads - two for dial and one for meters.

Kenwood KT-7000 and KT-7001:
8 volt, 250 milliamp X 7 fuse type.. Upper and lower indicators (AM, FM, Mute, MPX) are 8 volt, 150 milliamp bayonet base.. The KT-7000 stereo indicator light is 'special' -- it is an 8 volt, 30 milliamp miniature.

Kenwood KT-7001
8 volt, 300 milliamp X 6 (fuse type, meters and illumination) 8 volt, 150 milliamp X 2 (bayonet type, Muting and MPX) 8 volt, 40 milliamp X 3 (miniature, AM, FM, Stereo)

Kenwood KT-7300
8 volt 300 milliamp X 3 green-tinted bulbs with rubber grommet base and wire leads - two for dial and one for meters.

Kenwood KT-7500 and KT-7550
8 volt 300 milliamp X 3 green-tinted bulbs with rubber grommet base and wire leads - two for dial and one for meters.

Kenwood KT-6005 and KT-6007
Dial uses 8 volt 300 milliamp X 4 bulbs with rubber base that push over two pins, same as the Sansui TU-717.

Kenwood KT-8300
8 volt 300 milliamp (fuse type)

Luxman T-110
Dial lamps - 4 "bayonet style"
A #53 bulb .

Marantz 120
Dial lamps - 8 volt, 200 milliamp (fuse type)
Dial pointer lamp - 8 volt, 0.06 amp
Meter lamp - 8 volt, 0.2 amp
Selector indicators - Bi-pin 6.3 volt or 8 volt, 0.04 amp

Most Marantz tuners from the 1970s (including models 120, 150, 115B and 2120) use the same fuse-type, 8 volt, 180-200 milliamp dial illumination lamps.

Marantz receivers
Most 2200 Series Marantz receivers used an 8 volt 200 milliamp lamp for the tuning dial and an 8 volt 300 milliamp lamp for the two meters. The 2265B uses five lamps behind the tuning dial and one lamp each behind the signal-strength and tuning meters. The lamps run on AC from an 8-volt transformer winding. The bulbs, known as fuse lamps, look like 3AG fuses and are socketed in fuse holders.

Philips AH673 and AH6731
6.3 volt 40 milliamp X 3, 1/4 mini bayonette type ('GE 1302' bulb)
There are 13 of them in the tuner, 16 in the preamp and another 4 in the amp for this series.

Pioneer TX-7500
Dial illumination: 8 volt 300 milliamp "wedge type" lamps
Pilot ("power") and stereo indicators: 6 volt 30 milliamp X 2 "grain type" lamps with leads

Pioneer TX-9100
Tuning and signal-strength meter illumination lamps: 8 volt 300 milliamp.
AM, FM, stereo indicator and pointer: 40 milliamp (not sure of the voltage).

Pioneer TX-9500II
8 volt 300 milliamp X 4
8 volt 50 milliamp X 1
6 volt 30 milliamp X 3

Pioneer TX-9800
8 volt 300 milliamp 
6 volt 50 milliamp

Realistic TM-1001
8 volt 250 milliamp X 3
PL1: BF311-03030A 8V, 250 milliamp
PL2 and PL3: BF310-03030A 8V, 250 milliamp
The first one lights up the tuning dial and the bottom two light up the signal meter and multipath meter.

Sansui TU-217
No dial lamps used

Sansui TU-317
Dial uses 8 volt 300 milliamp X 3 bulbs with rubber base that push over two pins.

Sansui TU-417, TU-517, TU-519, TU-710, TU-717, TU-719, TU-919, TU-5900 and TU-9900
Dial uses 8 volt 300 milliamp X 4 bulbs with rubber base that push over two pins.

Sansui TU-7500
Stereo indicator lamp PL 010: 7 volt, 0.1 amp
FM/AM indicator lamps PL 007/008: 7 volt, 0.1 amp
Dial pointer lamp PL 009: 6 volt, 75 milliamp
Meter lamps PL 005/006: 6.3 volt, 0.25 amp

Sansui G-4700, G-5000, G-9000 and most (if not all) G-series receivers use the same bulb: 8 volt 200 milliamp bulb with rubber grommet base and wire leads.

Sansui TA-300 and TA-500 receivers
Although these receivers appear to have a TU-717 style case and face, they use different dial bulbs The bulbs in the TA-300/500 are wire leaded. They are 8 volt 300 milliamp like the TU-717 etc., but are not the push-on bulbs.

Sony ST-A6B:
Meters: bulbs say "6.3V .
Dial: 8 volt 300 milliamp X 3, "wedge base" bulbs.

Technics ST-9030
6.3 volt 40 milliamp X 2 (stereo and wide IF indicators)
6.3 volt 250 milliamp X 5 (fuse type)

Yamaha T-1
14.5 volt 80 milliamp X 4 (wire-ended, clear bulbs)

Yamaha T-2
14.5 volt 80 milliamp X 4 (wire-ended, clear bulbs)