Artikelbeschreibung
Angeboten wird ein Emulator für ELV   BMW E-Serie mit elektrischer  Lenkradverriegelung. Falls bei ihrem BMW die Lenkradverriegelung mechanisch defekt ist, kann der Emulator das Problem kostengünstig lösen. BMW Werkstatt  tauscht in dem Fall die komplette Lenksäule aus. Nach der Einbau hat das Fahrzeug keine Fehler mehr und startet ganz normal wieder. Die Lenkradverriegelung bleibt  in dem Fall außer Betrieb. 
BMW Modele: E60, E61, E63, E64

Es ist zu beachten, dass in einigen Fällen ein  Counter Reset im CAS Steuergerät  durchgeführt werden  muss. Dafür sind spezielle OBD Geräte und Wissen nötig.

1 Lösung
   Selbsteinbau:

Verkleidung unter Lenksäule (3 Schrauben) abbauen.
Den Stecker von ELV abziehen. Der befindet  sich ca. in der Mitte von der Lenksäule.
Emulator anstecken. WICHTIG: Die Pin 1 vom Emulator (Siehe Bild) muss mit der Pin 1 vom  Fahrzeug Stecker (Beschriftet)  überein passen (Pinbelegung  Regel).
Prüfen, ob die Meldung verschwunden ist. 
Falls die erste Lösung nicht geholfen hat, sollte man die Lösung 2 ersteigern.

2 Lösung:  Counter Reset mit Versand vom CAS Modul an uns.

    1)Uns bei Ebay per Nachricht kontaktieren und nach einem Preisvorschlag  fragen.
    2) Preisvorschlag akzeptieren und bezahlen.
    3) Batterie abklemmen. CAS Modul ausbauen und an uns  senden. Das Modul befindet sich unter
         der Lenksäule.
    4) Nach Erhalt von ihrem Modul wird es am selben Tag umprogrammiert und am nächsten Tag 
         wieder an Sie mit DHL als Paket verschickt.
    5) Sie bekommen von uns  ihr CAS Modul UND den Emulator zurück.
    6) CAS Modul und den Emulator  nach Lösung1  einbauen.
    7) In manchen Fällen muss die Wegfahrsperre mit einem Diagnose Gerät neu synchronisiert     werden.  Das ist aber erst nötig, wenn das Fahrzeug nach CAS Einbau nicht angesprungen ist.
     8) Fertig.
Für die Anleitung  zum Selbsteinbau können wir natürlich keine Haftung übernehmen. 
Kontakt: Siehe unten (Rechtliches)

Service
>Ausführliche Beratung
>Langjährige Erfahrung im Elektronik Bereich
______________________                                          Hinweis!
Nur zu Reparatur Zwecken gedacht! 
Keine dauer Lösung.

Englisch

Offered is an emulator for ELV BMW E-series with electric steering wheel lock. If the steering wheel lock on your BMW is mechanically faulty, the emulator can solve the problem cost-effectively. BMW Workshop will replace the complete steering column in this case. After installation, the vehicle has no more errors and restarts normally. The steering wheel lock remains in the case out of service.
BMW models: E81, E82, E87, E90, E91, E92, E93, E60, E61, E63, E64
MINI: R55, R56
It should be noted that in some cases a counter reset must be performed in the CAS control unit. This requires special OBD devices and knowledge.
1 solution
   Yourself installation:
Remove trim panel under steering column (3 screws).
Disconnect the plug from ELV. The is located approximately in the middle of the steering column.
Plug in emulator. IMPORTANT: The pin 1 of the emulator (see picture) must match the pin 1 of the vehicle connector (labeled) (pin assignment rule).
Check if the message has disappeared.
If the first solution did not help, you should bid for solution 2.
2 Solution: Counter Reset with shipping from the CAS module to us.
       1) Contact us on Ebay by message and ask for a price suggestion.
       2) accept price proposal and pay.
      3) Disconnect the battery. Remove CAS module and send it to us. The module is located at
         the steering column.
     4) After receiving your module it will be reprogrammed the same day and the next day
         sent back to you with DHL as a package.
     5) You get back your CAS module AND the emulator from us.
    6) Install CAS module and emulator after solution1.
    7) In some cases the immobilizer has to be re-synchronized with a diagnostic device. This is only necessary if the vehicle has not started after CAS installation.
     8) Done.
Of course, we can not accept any liability for the instructions for self-installation.
Contact: See below (Legal)

Warum Chiptuning von Speedlabor


Beratungsgespäch mit dem Kunden!

Fehlerspeicher des Fahrzeuges wird Ausgelesen!

Echtzeitdaten werden überprüft!
Original Software wird Ausgelesen und auf Originalzustand überprüft!
Aufbauend auf diesen Softwarestand und Updatestand wird ein neue Software entwickelt!
Diese wird dann in ihr Fahrzeug per OBD oder am Tisch programmiert!
Testfahrt mit Echtzeitdaten und Kontrolle und Anschließenden wiederholten Fehlerspeicher Auslesen
Wir Arbeiten nur mit Originalgeräten und keinen Chinesischen Flashern!
Wir Arbeiten nicht mit Datenbanken oder ungeprüften Softwareständen !
Wir wissen auch was wir machen müssen bei Abbrüchen oder sonstigen Problemen!
Wir lassen den Kunden nicht im Stich und haben genug Erfahrung!
Wir geben gerne Auskunft über die Veränderten Werte im Fahrzeug da wir dies auch wissen was wir gemacht haben!
Wir speichern ihre Original und Getuntesoftware bei uns ab unter ihrem Namen und das Rückspielen ist fast immer Kostenlos

Weitere Dienstleistungen entnehmen Sie bitte der Beschreibung!

 

 

Ihr Speedlabor Team !

Wissens

Was ist Chiptuning !?

Chiptuning ist ein Möglichkeit, die Leistung eines Fahrzeugs zu erhöhen oder zu optimieren. Moderne Fahrzeuge sind mit einem Motorsteuergerät ausgestattet, welches über die Kennfelder den Lauf des Motors regelt. Diese Kennfelder sind auf einem Chip oder einem Prozessor gespeichert. Dieser Chip befindet sich im Motorsteuergerät. Wird dieser Chip durch einen Chip mit modifizierten Kennfeldern ausgetauscht oder Programmiert spricht man von Chiptuning. Sofort nach dem Austausch oder der Programmierung ist die Mehrleistung sofort deutlich spürbar. Sowohl bei Benzin als auch Diesel Motoren kann Chiptuning durchgeführt werden. Ein weiterer Vorteil ist, dass sich durch Chiptuning auch der Kraftstoffverbrauch reduzieren lässt. In Zeiten hoher Spritkosten ist dies natürlich ein Vorteil.

Jeder Autohersteller stellt seine Motoren so ein, dass sie auch unter extremen Bedingungen von Umwelt und Kraftstoff funktionieren. Da wir in Europa (besonders in Deutschland), was diese Faktoren betrifft, hervorragende Bedingungen haben, ergibt sich die Möglichkeit, durch einen Eingriff ins Motor-Management (ECU - Engine control unit) ein höhere Leistung zu erzielen, ohne die Lebensdauer ihres Motors zu beeinträchtigen.

Bei gleicher Fahrweise werden Sie durch das höhere Drehmoment (= mehr Kraft) ein Kraftstoffersparnis von ca. 0,5-1,5 Liter pro 100km haben. Wir erreichen diese Leistungssteigerung durch ein Neuprogrammierung des Steuergeräts. Die elektronischen Einspritzsysteme von modernen Fahrzeugen sind mit einer Hardware ausgerüstet, die der eines Personalcomputers ähnelt. Dieser Computer errechnet alle für den einwandfreien Motorlauf notwendigen Daten. Durch Änderung der werksseitig vorgegebenen Daten in der Software des Herstellers, aber gleichzeitiger Beibehaltung der notwendigen Kontrollfunktionen, erreichen wir ein Leistung.

Englisch

Are you looking for a reliable supplier of Tuningfiles?
Then you are right with us!

We are specialists for expensive software best quality. Our products are relatively equivalent to the Software other tuning companies!


Do you also offer chip tuning and benefit from our quality and reliability!
You can earn good money as well by the way.

Our customers include many dealers and tuning companies world-wide!

Your advantages with us:

1.Files are manufactured individually according to customer requirements
2.Realistische Performance specifications
3. No standard files, each request will be processed in person
4.Zeitnahe processing, 7-days a week by appointment outside of business hours.
5.Files are available in various file formats
6.Bester service at a good price, between 50-150 Euros

If you send us the original file via e-mail, you have the right Tuning File usually within 30 minutes available.
Alsauch We can offer devices to flash. We work with the company DIM sport very closely and can offer you the best Flash devices on the market!
We only offer tested tuning files and power torque increases to the realistic framework in order to avoid damage to the vehicle. We manufacture the tuning files for almost all control units, like :. Bosch EDC 15, EDC 16, MED17, EDC17, Siemens, Delphi, Magneti Marelli, MSD8x, Visteon etc.

""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

Intake meeting with the customer!
Fault memory of the vehicle is read!
Real-time data will be checked!
EPROM is read and checked for its original condition!
Based on this software version and update status, a new software is developed!
This is then programmed into their vehicle via OBD or at the table!
Test drive with real-time data and control and subsequently repeated fault memory
We only work with original equipment and no Chinese flashers!
We work not with databases or untested software versions!
We also know what we have to do in case of demolitions or other problems!
We do not let our customers down and have plenty of experience!
We are happy to provide information about the changed values in the vehicle as we know what we have done so well!
We store your original and Tuned Software at us from under their name and return play is almost always free
Other services can be found in the description!
Your Speed laboratory team!

""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""

What is chiptuning?

Chip tuning is one way to increase the performance of a vehicle or to optimize. Modern vehicles are equipped with an engine control unit, which regulates the rotation of the motor on the characteristic maps. These maps are stored on a chip or a processor. This chip is located in the engine control unit. If this chip replaced by a chip with modified maps or programmed is called chip tuning. Immediately after replacing or programming the extra power is immediately noticeable. Both petrol and diesel engines can chip tuning be performed. Another advantage is that it is possible by Chiptuning also reduce fuel consumption. In times of high fuel costs, this is of course an advantage.

Each automaker presents its engines so that they work even under extreme conditions of the environment and fuel. Since we have excellent conditions in Europe (particularly in Germany), with regard to these factors, there is the possibility, by an intervention in the engine management - to achieve higher performance, without the life of your engine (ECU Engine Control Unit) affect.

With the same procedure you are the higher torque (= more power) have a fuel economy of about 0.5-1.5 liters per 100km. We achieve this performance improvement through a reprogramming of the control unit. The electronic injection systems of modern vehicles are equipped with hardware that is similar to a personal computer. This computer calculates all the information necessary for the smooth running engine. By changing the factory preset data in the manufacturer's software, but while maintaining the necessary control functions, we achieve a performance.

Your Speedlabor Team!

 

"""""""""""""""""""""""""""""""""""""""""""""""""""

A также мы говорим по русски!!!

Rechtliches

Mit diesem Gebot akzeptieren Sie unsere AGB (Allgemeine Geschäftsbedingungen). Sie finden diese auf unsere Ebay Mich-Seite.