|
MC31 HHO Dry Cell -
Mini 31 Plate 1-2.75 LPM Hydrogen Generator |
International, please send a message with qty and destination if you want to purchase more than 1. Multiple items ship together.
***Free Shipping Within
the United States***
This cell is shipped USPS with tracking number and will generally ship
within 48 hours (excluding weekends) of purchase.
Outside US and Canada, please send a message. Following is shipping prices for International.
Qty 1: $52
Qty 2: $52
Qty 3: $52
Qty 4: $70
Up to 3 units can be shipped in 1 medium flat rate, via usps. 4 units will fit in 1 large flat rate.
***Note,
we do not sell installation kits. However, we can provide you with
direct sources for all the hardware. Please do not buy installation kits
from resellers. For the MC31, it should cost you no more then $50 for
all the hardware, plus $30 for a pwm, and then the EFIE. Resellers
add 200-300% onto the cost, plus you still have to purchase a PWM and an EFIE if it is for automotive applications. Save yourself some cash, a lot of cash.
| This Dry
Cell is similar in size to other dry cells, of 3.5" plate size, but with 31
plates and capable of producing more than 50% increased HHO during average
usage. This Dry Cell can produce 2-2.75 LPM realistically @ 30-35 amps 12-14v DC,
without creating steam for long durations.
A 7 Plate dry cell using 3.5"X3.5" plates
with the corners trimmed has an overall surface area of 171". This Dry cell
has an overall 372" of surface area. That 25% more surface area within the
cell, but the same overall dimensions. Not only that, this dry cell squeezes
out every last square millimeter of surface area for that production.
The end plates are constructed of high
tensile strength cpvc, not acrylic or abs. These end plates will not crack like the
clear acrylic will or disintegrate like ABS from the chemical reaction
process. They can withstand the pressure, will not disintegrate,
can be torqued down without breaking, and able to withstand any harsh
condition from -50 Fahrenheit to 200 Fahrenheit. Using this material costs
more, but it is well worth it, considering that using a dry cell with
acrylic end plates will last a few months, these will last for years.
The gaskets are perfectly spaced for maximum efficiency. If gaskets are too narrow, dry cells will produce too much heat, but if they are too thick then a huge loss of production will occur. Finding that point of balance to ensure long term efficiency and minimal heat generation is critical. All our cells are engineered to meet those specifications time and time again.
|
Fuel Cell LLC MC31
Click to Enlarge Images
Technical
Specifications:
Length: 5" (7" Including Fittings)
Width: 3"
Height: 4"
Power Requirements: 12v-14v / Minimum 2 amp-10 amps and can operate up to
35 Amps continuously
Plates: 31
Gaskets: 32
Cell Surface Area: 372"
Performance: .75 LPM at 10 Amps - 2.5 LPM at 30 Amps Arrangement: +NNNNN-NNNNN+NNNNN- (2
Full Series of Pos/Neg for automotive voltages)
Fittings/Plumbing: 2 X 3/8" NPT Barbed Elbows for 1/2" Hose (Fittings can be
changed as per your own requirements)
Manufacturer: Fuel Cell LLC MADE IN THE USA (Iowa to be specific) |
Generic Acrylic Cells
*Notice only 1 hole through the plates? Majorly not a good thing. Where does the cell fill up at? Through the top in the HHO out holes.
What Not To Use in HHO:
Clear Acrylic & ABS Plastic
Examples of the Don'ts Acrylic
ABS Plastic (Textured)
 |
|
HHO Dry Cell Tips:
- When you are using a single water
in, single hho out Dry Cell, you will increase your flow rate and remove
back flow issues by mounting the cell at an angle or vertically.
- Do not ever use "Tap Water".. The
results from chlorine in the wate will create a brown sludge, will clog
the lines and gunk up the cell. You will be rebuilding within days.
- 28% KOH mixture will not freeze
down to about -50F
- IF YOU SEE VIDEOS OF DRY CELLS WITH
VAPOR COMING OUT OF THE CELL/BUBBLER, THAT IS STEAM! ""It means the cell
has turned into a hot water heater, not a HHO producing cell"" HHO IS
CLEAR AND NO VAPORS. ****Steam will destroy your engine****
HHO Dry Cells, what to use:
- Distilled Water
- KOH - Potassium Hydroxide
- Anti Foam
Potassium Hydroxide: Is best used with
HHO because of its superior electrolyzing ability. Mixture should be 20-28%
by weight. Weight of water is 8.34lbs. So, anywhere from 26oz-34oz of KOH
per gallon of distilled water will prove the best results. In the video
below, the mixture is 20%.
Anti Foam: HHO Dry Cells can foam. The
foam can be bad if you do not have a scrubber. Simple solution. Every spa
and jacuzzi store carries Anti Foam. Generally about $10 per bottle, add
about 1/2 cup of anti foam per 1 gallon of Distilled Water/KOH mixture...
Problem solved. Your mixture will remain potent and your fluids will remain
foam free. :)
*** Do not
use tap water for HHO Dry Cells. Distilled Water with Potassium Hydroxide (KOH)
is used best. ***
MC19 Dry Cell Demo (MC31 50% more plate configuration_
*Note, I used to call this cell the MC31. 31 is 31 plates,
this is 19.
More Videos, Click Here
|
|
