Solar Controller Diversion load regulator Charge regulator
Charge controller Battery regulator 12 volt 24 volt 48 VDC volt wind
power charge controller renewable energy dump load diversion load
440 AMP WIND / SOLAR
New push button load tester - "PUSH THE BUTTON ™
12 VOLT / 10,000 WATT BATTERY CONTROLLER
Fully programmable for any voltage from 14.4 to 12.2
(recommended 14.4 to 13.6 for long battery life)
This is a test button to turn your dump load on and off. Other sellers are too uneducated to actually reprogram a micro controller so they use a stock unit that will drain your battery down to 10.8 Volts which slowly wears them out. Be very careful you get our reprogrammed controller and not a cheap imitation made by a 10th grader who's best attribute is telling lies about other people. YES PUSH THIS BUTTON since our re-programing has turned it into a true dump load "ON" / "OFF" switch.
FULLY ASSEMBLED AND PROGRAMMED READY TO GO!
DUMP MODE 12 volt only
CUT MODE 12 volt only
Battery regulator for both your wind and solar battery input power.
This regulator can either dump extra power creating free hot water or heat
or just cut off extra power to keep your batteries from over charging.
This unit is a must for wind turbine applications as it uses a
mechanical relay which can handle high voltage surges unlike solid
state controllers.
15 years of great products
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions. This controller was specially developed for wind turbines. Also works on solar too - Get one battery controller to do it all!
Worlds
Lowest Cost 440
AMP
Wind
& Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load
Regulation-
For solar panels and solar
LOWEST COST 440 AMP CHARGE OR DIVERT CONTROLLER WITH DIGITAL DISPLAY ON THE MARKET
Max solar amperage in divert (dump) mode is 440 amps. This is a big hybrid wind and solar charge controller.
Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both. User changeable settings -- Several controllers on the market only let you set the dump level! Connect multiple turbines and solar panels up to 440 amps worth at the same time! Max continuous solar amperage in disconnect mode is 100 amps. 440 Amp in Dump.
Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source. You can connect both wind and solar at the same time. Reverse polarity protection
Ultra low power consumption even with the volt meter on (almost
negligible). You can even set the volt meter to turn off after
in-activity.
On board relay- Isolates electronics from back voltage spikes from large 440 amp relay.
This is important to get the longest life out of the electronics. No body else has this!
Dual (2) Microprocessor controlled -- Extremely stable and very accurate
Multiple user changeable settings, and trip points for many various
system requirements and applications- You can change the dump point
voltage level,
end of dump voltage level, length of time in
divert mode when end dump point voltage is reached
Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.
Battery Status digital - Lets you know your battery's actual voltage in real time!
Plug and Play - Long leads for easy termination to your 12 volt battery or battery bank.
Battery regulator for both your wind and solar battery input power.
This regulator can either dump extra power creating free hot water or heat
or just cut off extra power to keep your batteries from over charging.
This unit is a must for wind turbine applications as it uses a
mechanical relay which can handle high voltage surges unlike solid
state controllers.
10,000
WATT Rated (Tested
to 467 Amps)
Controller only requires 12 volt power for total power sampling from any battery bank
15 years of great products
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions. This controller was specially developed for wind turbines. Also works on solar too - Get one battery controller to do it all!
Worlds
Lowest Cost 440
AMP
Wind
& Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load
Regulation-
This controller
can divert or simply disconnect
incoming
power without
an electrical arc occurring -
HOW
POWER DRAW DYNAMICS WORKS:
This
High Amp unit can
control 12 wind turbines or 40 solar panels !
Used to prevent battery over
charging
onWind -
Solar - Hydro
A
battery regulator diverts
excess power to power
some
other useful device
when ever your battery is full.
Use
the this excess power
to make free hot water or to
recharge an auxiliary
battery bank, so many uses!
Has push button load tester.
An
extremely robust
unit!
draws
almost ZERO power while
sensing! 99.998%
electrically efficient
while sensing!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
"Cut" charge controller.
Diversion load
regulator.
Micro processor
controlled.
Versatile raised steel
mounting plate.
Measures
10" long by 7" wide by 3" tall.
Works for all Wind
Turbines, Solar panels and
Hydro.
For all voltages
ranges in multiple battery
banks.
No grounded IGBT's or MOSFETS -
Lighting strike proof
isolation.
CUT -LOAD controller (No need to buy a dump load resistor)
Electrically
efficient. Draws only trace
power while sensing!
Does not waste
electricity while sensing
in diversion load mode!
HOW
POWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses no
power when it is NOT dumping (energy efficient sensing)
The modern way to
monitor your battery from over charging
is to have a diversion load that performs another task such as
heating water when your battery is in danger of over charging.
Shutting down the output of your wind turbine or your other renewable
energy devices is old school thinking. Now-a-days most people
dump their excess power into some other legitimate device optimizing
their energy independence. Hot water from your excess power can
be used for radiant heating in the winter or even in the hot
summer months for washing cloths or dishes and for bathing. You
will always find a need for hot water in your life.
Extra
heavy duty continuous
duty relay that can handle millions
of cycles at very high amp
loads without fusing together or sticking! -
"Electro
mechanical
units ours are impervious to lighting, EMP and static electrical
discharges"
"Simple
and ultra-reliable"
- "A BULLET PROOF SYSTEM"
CUT MODE OPERATION
Solar Controller Diversion load regulator Charge regulator
Charge controller Battery regulator 12 volt 24 volt 48 VDC volt wind
power charge controller renewable energy dump load diversion load
440 AMP WIND / SOLAR
New push button load tester - "PUSH THE BUTTON ™
12 VOLT / 10,000 WATT BATTERY CONTROLLER
Fully programmable for any voltage from 14.4 to 12.2
(recommended 14.4 to 13.6 for long battery life)
This is a test button to turn your dump load on and off. Other sellers are too uneducated to actually reprogram a micro controller so they use a stock unit that will drain your battery down to 10.8 Volts which slowly wears them out. Be very careful you get our reprogrammed controller and not a cheap imitation made by a 10th grader who's best attribute is telling lies about other people. YES PUSH THIS BUTTON since our re-programing has turned it into a true dump load "ON" / "OFF" switch.
FULLY ASSEMBLED AND PROGRAMMED READY TO GO!
DUMP MODE 12 volt only
CUT MODE 12 volt only
Battery regulator for both your wind and solar battery input power.
This regulator can either dump extra power creating free hot water or heat
or just cut off extra power to keep your batteries from over charging.
This unit is a must for wind turbine applications as it uses a
mechanical relay which can handle high voltage surges unlike solid
state controllers.
15 years of great products
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions. This controller was specially developed for wind turbines. Also works on solar too - Get one battery controller to do it all!
Worlds
Lowest Cost 440
AMP
Wind
& Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load
Regulation-
For solar panels and solar
LOWEST COST 440 AMP CHARGE OR DIVERT CONTROLLER WITH DIGITAL DISPLAY ON THE MARKET
Max solar amperage in divert (dump) mode is 440 amps. This is a big hybrid wind and solar charge controller.
Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both. User changeable settings -- Several controllers on the market only let you set the dump level! Connect multiple turbines and solar panels up to 440 amps worth at the same time! Max continuous solar amperage in disconnect mode is 100 amps. 440 Amp in Dump.
Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source. You can connect both wind and solar at the same time. Reverse polarity protection
Ultra low power consumption even with the volt meter on (almost
negligible). You can even set the volt meter to turn off after
in-activity.
On board relay- Isolates electronics from back voltage spikes from large 440 amp relay.
This is important to get the longest life out of the electronics. No body else has this!
Dual (2) Microprocessor controlled -- Extremely stable and very accurate
Multiple user changeable settings, and trip points for many various
system requirements and applications- You can change the dump point
voltage level,
end of dump voltage level, length of time in
divert mode when end dump point voltage is reached
Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.
Battery Status digital - Lets you know your battery's actual voltage in real time!
Plug and Play - Long leads for easy termination to your 12 volt battery or battery bank.
Battery regulator for both your wind and solar battery input power.
This regulator can either dump extra power creating free hot water or heat
or just cut off extra power to keep your batteries from over charging.
This unit is a must for wind turbine applications as it uses a
mechanical relay which can handle high voltage surges unlike solid
state controllers.
10,000
WATT Rated (Tested
to 467 Amps)
Controller only requires 12 volt power for total power sampling from any battery bank
15 years of great products
This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions. This controller was specially developed for wind turbines. Also works on solar too - Get one battery controller to do it all!
Worlds
Lowest Cost 440
AMP
Wind
& Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load
Regulation-
This controller
can divert or simply disconnect
incoming
power without
an electrical arc occurring -
HOW
POWER DRAW DYNAMICS WORKS:
This
High Amp unit can
control 12 wind turbines or 40 solar panels !
Used to prevent battery over
charging
onWind -
Solar - Hydro
A
battery regulator diverts
excess power to power
some
other useful device
when ever your battery is full.
Use
the this excess power
to make free hot water or to
recharge an auxiliary
battery bank, so many uses!
Has push button load tester.
An
extremely robust
unit!
draws
almost ZERO power while
sensing! 99.998%
electrically efficient
while sensing!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
"Cut" charge controller.
Diversion load
regulator.
Micro processor
controlled.
Versatile raised steel
mounting plate.
Measures
10" long by 7" wide by 3" tall.
Works for all Wind
Turbines, Solar panels and
Hydro.
For all voltages
ranges in multiple battery
banks.
No grounded IGBT's or MOSFETS -
Lighting strike proof
isolation.
CUT -LOAD controller (No need to buy a dump load resistor)
Electrically
efficient. Draws only trace
power while sensing!
Does not waste
electricity while sensing
in diversion load mode!
HOW
POWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses no
power when it is NOT dumping (energy efficient sensing)
The modern way to
monitor your battery from over charging
is to have a diversion load that performs another task such as
heating water when your battery is in danger of over charging.
Shutting down the output of your wind turbine or your other renewable
energy devices is old school thinking. Now-a-days most people
dump their excess power into some other legitimate device optimizing
their energy independence. Hot water from your excess power can
be used for radiant heating in the winter or even in the hot
summer months for washing cloths or dishes and for bathing. You
will always find a need for hot water in your life.
Extra
heavy duty continuous
duty relay that can handle millions
of cycles at very high amp
loads without fusing together or sticking! -
"Electro
mechanical
units ours are impervious to lighting, EMP and static electrical
discharges"
"Simple
and ultra-reliable"
- "A BULLET PROOF SYSTEM"