Change the surface design quickly with SPRAYPLAST strippable
lacquer. You can very individually design the look of e.g. your rims or other
objects and car parts. If you do not like the colour any more, simply peel off
the film, which has been sprayed on before.
SPRAYPLAST is not just suitable to design your rims, but you
can also apply it on blank metal, all 2K coatings, paintable hard plastics and
on glass. Even the large-area painting of e.g. car parts is possible, if you
apply a sufficient thick layer.
SPRAYPLAST is not suitable to paint headlights, rear lights
or other surfaces of polycarbonate.
Depending on size and structure of the rim, the content of a
single aerosol could be sufficient for up to 2 rims.
SPRAYPLAST is not just suitable to paint cars, but also
objects of everyday's use and DIY.
We recommend to apply at least 5 coats.
Quality and properties
ONE single aerosol
High-grade quality
Quick-drying
Protective coat against
stone-chips, scratches, dirt, wetness
Resistant to diluted acids,
fats, oils
Very good coverage
Excellent adhesion on many
materials such as metals, plastics (PP, PE, PVC), glass
Not applicable on porous
surfaces, e.g. wood, concrete, stone
Good flow, smooth surface
Suitable to paint indoor and
outdoor objects
Do not apply on 1K lacquers,
but only on blank metals, 2K paintwork, original car paintwork.
Very good resistant to
customary cleaning agents (e.g. rim cleaner)
Short-term resistant to car
wash plants
Not conducting, but not
electrical isolating!
Only coatable with
SPRAYPLAST-products.
Physical and chemical data
Basis of the binder: rubber-like polymere
Colour: TRANSPARENT GLOSS
Smell: solvent
Degree of gloss (at measurement angle 60°
acc. to DIN 67530):
satin-gloss: >70
mat: <10
Gloss Finish: >80
Efficiency: Depending
on consistence and colour of the ground:
400 ml are sufficient for 0.2 - 0.4 m² (if 5 layers are applied)
Drying time (at 20°C, 50%
relative air humidity): Dust-dry:
after approx. 10 minutes
Dry to touch, peelable: after approx. 2 hours
Cured: after approx. 6-8 hours
The drying time depends on surrounding temperature, air humidity and
thickness of the applied coat.
Temperature-resistant: approx. 100°C
Storage stability: 10
years, if appropriate storage provided (=10°-25°C, relative air humidity
of max. 60%), storage in the closed, original container. Store frost-free.
Size: aerosol cans, maximal
nominal volume 400 ml, as set with 2 cans of 400 ml
Environment and labelling
Environmentally
sound: The
products of MOTIP DUPLI are 100% free of heavy metals. The caps and packagings
are made of recyclable material.
Disposal: Only the completely emptied cans should be put into the
recycling skip or appropriate container for reclaimable refuse. Cans which are
not empty should be disposed off as "special refuse".
Marking/Labelling: All products made by MOTIP DUPLI comply with
the actual labelling regulations according to Preparation Guideline 1999/45/EG.
All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol
guideline 75/324/EWG in the actually valid version.
Using instructions
The most
DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap.
This is to avoid unauthorized use. Please see the corresponding advises on the
cap or on the label. Before use, carefully read and observe the warning texts on the label!
Preparation:
The ground you want to treat
has to be clean, dry and free from rust and fat as well as smooth and
solvent-resistant.
Do not paint on porous or rough
surfaces. From smooth surfaces you can easily peel off the film
afterwards.
Do not prime!
Mask the area wich you do
not want to paint carefully with paper.
Before application, the
object which you want to paint, has to be cleaned thoroughly from fat, oil
or silicone with a customery, not too sharp cleaning agent (e.g. presto
383328). Before painting with SPRAYPLAST clean the surface with SPRAYPLAST
Cleaner art.no. 433351.
Application:
Before use, shake the can
thoroughly for 2 - 3 minutes.
Test the spray at an
unobstrusive spot; this makes sure that the can's contents has the desired
colour, and that the surface is compatible with the paint.
Spray crosswise layers from
a distance of 25 cm. Apply a very thin layer first (do not try to get
coverage immediately). Then apply at least 4 more layers of
SPRAYPLAST.
The more layers you apply,
the better you can remove the foil afterwards.
It is important to allow
each layer to dry for approx. 10 minutes, before you apply the next coat.
This way you can apply coat after coat.
In case you wish a
high-gloss surface, you can apply 1 cross-coat of the SPRAYPLAST Gloss
Finish
Advices for the painting of rims:
Carefully mask wheels and
inner surface of the rim with e.g. paper. To fix the paper you can use
customary masking tape.
Remove the masking paper and
tape immediately after painting the last layer.
To avoid that the paint coat
cracks, you should coat sufficiently thick in critical areas (e.g. angles
and edges). Anyhow, you can easily repair cracks and damages in the film
by applying a new coat of SPRAYPLAST.
Advices
for the painting of Neon colours:
It is necessary to have a
white ground of SPRAYPLAST. Please apply 4 coats in white and one coat in
the Neon colour.
Advices
for the painting with Gloss Finish:
You can use the Gloss Finish
as final coat to give earlier painted matt or satin-gloss shades a
high-gloss. In this case you have to apply 4 coats of colour shade and 1
coat of the Gloss Finish
If you use Gloss Finish as a
transparent high gloss protective coat, you have to apply 5 coats of the
Gloss Finish.
After
application:
Approx. 6 - 8 hours after
applying the last coat, the SPRAYPLAST is fully dry.
The painted coat does resist
very good to customary cleaning agents (SPRAYPLAST Cleaner art.no.
433351).
It is also possible to clean
the rims in the car wash plant.
In case of steam-cleaning,
keep a distance of at least 25 cm.
Tips for spray painting
Protect
the object and the surrounding area from spray mist.
Temperature should range between +10°C and +25°C, max. air humidity 60 %.
Store in
a dry place. Protect from direct sunlight and other sources of heat. Use only
during dry weather, in places protected from the wind, and in well-ventilated
rooms. Follow the warning texts on the labels!