Descriptions
The latest upgraded salable 5 axis breakout board is speacilly designed for the CNC single axis stepper driver controller, such as M542, M542H, MA560, MA860H, 2M542, 2M982 etc single axis stepper driver controller. With this 5 axis breakout board, any 1-5 single axis stepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc..
The M542 Stepper Driver Board Controller is a high performance microstepping driver based on pure-sinusoidal current control technology. With this technology and the self-adjustment technology (self-adjust current control parameters) for different motors, the drive motors can run with less noise, lower heating, smoother movement and have better performances at higher speed than most of the drivers in the market. It is suitable for driving 2-phase and 4-phase hybrid stepping motors, so the Nema17--Nema34 stepper motors with a 1.0A-4.5A current will be suitable.
In short, with this CNC Kit, you will get more benefits from the Kit on CNC work. Please purchuse this kit with confidence.
Features
I. 5 Axis Breakout Board
Upgraded circuit, work more peacefully and steady than the previous version
Maximum support 5-axis stepper motor driver controller
Two types of ways to get power, 5V DC power supply or USB port to directly get power from PC
Two-stage signal processing, smooth signal transmission, powerful anti-jamming
5-input interface to define the Limit, Emergence-Stop, Midpoint-Alignment, Cutter-Alignment, etc.
Relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
5-axis work LED display, visually display the working condition of the stepper driver controller
II. M542 Stepper Driver Board Controller
High performance, cost-effective
Supply voltage from 20V DC to 50V DC
Output current from 1.0A to 4.5A
Self-adjustment technology, full to half current self-adjustment when motors from work to standstill via switching off SW4
Pure-sinusoidal current control technology
Pulse input frequency up to 300 KHz
TTL compatible and optically isolated input
Automatic half-current reduction as long as switching off SW4 when motors stop
16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
Suitable for 2-phase and 4-phase motors
Support PUL/DIR and CW/CCW modes
Short-voltage, over-voltage, over-current and short-circuit protection, protect the PC, motors, driver etc from being damaged
Applications
Suitable for any small-and-medium automatic equipment with CNC controller, such as X-Y tables, labeling machines, laser cutters, engraving machines, and pick-place devices
Suitable for a wide range of stepping motors, from NEMA size 17 to 34
For processing various pattern mould
For advising, such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc.
For carving portrait, scenery, handwriting, sealing, etc.
I. DIP-Switch Instructions
II. DIP-Switch Settings Diagram
|
Dynamic current setting
|
|
Peak Current
|
AVG Current
|
SW1
|
SW2
|
SW3 |
| 1.5A |
1.0A |
ON |
ON |
ON |
| 2.0A |
1.4A |
OFF |
ON |
ON |
| 2.4A |
1.7A |
ON |
OFF |
ON |
| 2.8A |
2A |
OFF |
OFF |
ON |
| 3.2A |
2.3A |
ON |
ON |
OFF |
| 3.7A |
2.6A |
OFF |
ON |
OFF |
| 4.2A |
3A |
ON |
OFF |
OFF |
| 4.5A |
3.2A |
OFF |
OFF |
OFF |
| Auto Half-Current-Reduction Setting |
| SW4 |
ON |
OFF |
| Work-Full |
Standstill-Full |
Work-Full |
Standstill-Full |
| Mirostep Resoltion Selection |
| Mirostep |
Step/Rev.(1.8° motor) |
SW5 |
SW6 |
SW7 |
SW8 |
| 2 |
400 |
ON |
ON |
ON |
ON |
| 4 |
800 |
ON |
OFF |
ON |
ON |
| 8 |
1600 |
ON |
ON |
OFF |
ON |
| 16 |
3200 |
ON |
OFF |
OFF |
ON |
| 32 |
6400 |
ON |
ON |
ON |
OFF |
| 64 |
12800 |
ON |
OFF |
ON |
OFF |
| 128 |
25600 |
ON |
ON |
OFF |
OFF |
| 256 |
51200 |
ON |
OFF |
OFF |
OFF |
| 5 |
1000 |
OFF |
ON |
ON |
ON |
| 10 |
2000 |
OFF |
OFF |
ON |
ON |
| 25 |
5000 |
OFF |
ON |
OFF |
ON |
| 50 |
10000 |
OFF |
OFF |
OFF |
ON |
| 125 |
25000 |
OFF |
ON |
ON |
OFF |
| 250 |
50000 |
OFF |
OFF |
ON |
OFF |
Power supply Recommend:
24V DC power supply for Nema 17 stepper motors
36V DC power supply for Nema 23/24 stepper motors
48V DC power supply for Nema 34 stepper motors
