Description

Package included:
1 x 12V 1CH / 2 CH Wireless Relay Switch

1CH / 2 CH DC12V 10A independent wireless controller
Applicable for controlling family, office, shopping malls, hotels, hospital, warehouses and other places of fluorescent lamps, energy-saving lamps, incandescent lamp, halogen lamp, and the electric water heater through a power on-off control of household appliances.
it can learn 2272 2262 or 1527 chip with the different code wireless remote control

Learning :
Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control (press 1 times to learn Momentary;2times-Toggle;3times-Latched)

Remove/clean :
Press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .

Features :
2 CH Wireless Receiver Relay

1 .Board dimension: (LxWxH)45*30*16mm
2. Box dimension: (LxWxH)53*38*22mm
3 .Work Voltage: DC12V
4. Work Load: 10A
5. Work Frequency: 315MHz
6. Receiver Sensitivity: -108dBm
7. Wock Temperature: -20℃~+70℃（-4℉~158℉）
8. Output: switching signal / voltage output
9. The code way: Learning
10. Quiescent Current: ≤8mA

Output working way
1.Inching: press&hold one button, the reply turns on, release the button, the reply turns off.
2.Self-lock: press the one button, the reply turns on, press the button again, the reply turns off.
3.Interlock: press the one button, the reply turns on, press the next button, the reply turns off.
4.Two-way independent Output


1 CH Wireless Relay Switch

1.Input Voltage: DC10-14V
2.Standby Current: ＜5MA
3.RF Frequency: 433MHZ
4.RF Working mode:Super heterodyne receiver
5.Receiver Sensitivity: >90dBm
6.Remote Control Distance: >100 meter(In open environment)
7.Decoding Way: MCU Software decoding
8.Can store the number of remote control:50
9.Support remote control type: Fixed code, learning code
10.Channel: 1CH
11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
12.Wiring Method:Fixed wiring terminal
13.Working Voltage: DC12V
14.Output Current: 10A
15.Rated load:10A 250VAC / 10A 125VAC
10A 30VDC / 10A 28VDC
16.Output:Normally open,Common,Normally closed
17.Dimension:3.5cm*3cm*1.6cm

Working/output way:
1.Jog/Non-Latched: Press one button is Working /ON. Loosen your finger on the same button is Stop/OFF. One channel switch need one buttons remote control.
2.Self -lock/Self-Latched: Press one button for one time is working/ON. Press the same button again is stop/OFF. One channel switch need one buttons remote control.
3.Inter-lock /Latched: Press one button is working/ON, press another button is stop/OFF. One channel switch need 2 buttons remote control.
4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay

Note:If want to change the modes, need delete the present learning mode(Press the white learning button on the control panel eight times), and then re-learn the new features

Reset new operating mode
1. Jogging
Press the white learning button on the top of the control panel, LED lights, and then press any button on the remote control set to 'Jog' button, the control panel LED lights flashing, indicating that the setup is complete
2. Self-locking
Press the white learning button on the top of the control panel, LED lights, and then press any button on the remote control to set to 'self-locking' button, the control panel LED lights flashing,
3. Interlock
Press the white learning button on the control panel, the LED lights, and then press any button on the remote control set to 'start' button, the control panel LED lights flashing, press another button to set to 'stop' button LED Blinking means the setting is complete