biete einen HP3000 A500-200 server. Normalerweise läuft auf diesen Maschinen MPE/iX. Diese Kiste ist im wesentlichen eine HP9000 rp2470 mit einer leichter modifizierten firmware. Man kann auch HP-UX oder Linux auf dem server installieren. Es ist eine Festplatte mit MPE/iX 7.5 dabei, sowie einen Ersatzplatte. 2 * 650MHz PA8700 CPUs (läuft mit 200MHz unter MPE/ix) 3GB RAM zwei Festplatten zwei PCI SCSI controller Privatverkauf ohne Garantie oder Gewährleistung -------------------------------------------- this auction is for a HP3000 A500-200 server. It naturally runs MPE/iX. This is basically a HP9000 rp2470 with a slightly different firmware. It will also run HP-UX or Linux without problems. There is one harddisk with MPE/iX 7.5 on it and a spare disk. 2 * 650MHz PA8700 CPUs (clocked at 200MHz when running MPE/ix) 3GB RAM two hard disks two PCI SCSI controllers this is a private sale without any warranty. International shipping is possible to most places. Please ask for shipping costs. ---------------------------------- ********** VIRTUAL FRONT PANEL ********** System Boot detected ***************************************** LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF OFF ON ON LED State: Running non-OS code. (i.e. Boot or Diagnostics) processor system shutdown 1D00 processor system shutdown 1D00 platform config 6224 platform config 6224 [...] processor slave rendezvous 1C40 processor test 1142 processor test 113B platform test 612A I/O config 8238 ***************************************** ************ EARLY BOOT VFP ************* End of early boot detected ***************************************** Firmware Version 42.19 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-2001, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State CoProcessor State Cache Size Number State Inst Data --------- -------- --------------------- ----------------- ------------ 0 650 MHz Active Functional 750 KB 1.5 MB 1 650 MHz Idle Functional 750 KB 1.5 MB Central Bus Speed (in MHz) : 120 Available Memory : 3145728 KB Good Memory Required : 169572 KB Primary boot path: 0/0/1/1.15 Alternate boot path: 0/0/2/0.6 Console path: 0/0/4/1.643 Keyboard path: 0/0/4/0.0 Processor is starting autoboot process. To discontinue, press any key within 10 seconds. 10 seconds expired. Proceeding... Trying Primary Boot Path ------------------------ Booting... Boot IO Dependent Code (IODC) revision 1 HARD Booted. MMSAVE Version 2.8 DUMPAREA protected, proceeding to ISL without memsave ISL loaded ISL Revision A.00.43 Apr 12, 2000 Cannot find an auto-execute file. AUTOBOOT ABORTED. ISL> start MPE/iX launch facility Scanning PCI BUS 0 +**.*........................... Scanning PCI BUS 10 ................................ Scanning PCI BUS 20 +............................... Scanning PCI BUS 30 ..+............................. Initialize_genesis - Ver bld1: <<pci 2.1601>> SUN, JAN 29, 2017, 3:46:03 PM (y/n)? y Initialize_genesis = Ready to configure I/O [CDM] 03 07 02 12 Initialize genesis completed. Create Console Messages kso completed. Initialize memory manager completed. Initialize resident kernel completed. Initialize volume management and mount the System Disk Initialize volume management completed. Opening the native system library completed. Initialize loader completed. I/O boot path managers frozen in memory completed. Vsm make no longer resident completed. Initialize process management completed. Initialize debug subsystem completed. Initialize file system completed. Initialize temporary UID/GID Databases completed. Initialize non-resident services completed. Begin binding compatibility mode SL Compatibility mode SL binding complete Create port process has been completed. The following is a list of the boot options - last boot command: START last configuration group: CONFIG current boot command: START current configuration group: CONFIG Last configuration group actually used by START: CONFIG logon = OPERATOR.SYS RECOVERY MULTI-USER MULTI-DISK SYSSTART Begin launching additional processors: Launch processor 1 successful. Successfully launched 2 out of 2 total processors. Entering - System I/O configuration. The path 0 has already been configured. The path 0/0 has already been configured. The path 0/0/1 has already been configured. The path 0/0/1/1 has already been configured. The path 0/0/1/1.15.0 has already been configured. The path 0/0/2/0.16.0 was configured but is not available. The path 0/0/2/0.17.0 was configured but is not available. The path 0/0/2/0.6.0 was configured but is not available. The path 0/0/2/1.15.0 was configured but is not available. The path 0/0/4 has already been configured. The path 0/0/4/1 has already been configured. The path 0/0/4/1.0 has already been configured. The path 0/4/0/0.0.0 was configured but is not available. The path 0/4/0/0.2.0 was configured but is not available. The path 0/6/2/0.0.0 was configured but is not available. The path 0/6/2/0.2.0 was configured but is not available. Leaving - System I/O configuration. dDSYSTEM I/O AT BOOT TIMEd@ ldev: 1 ST39103LC configured available 0/0/1/1.15.0 ldev: 2 ST39103LC configured not-available 0/0/2/1.15.0 ldev: 6 LP_PP_ID configured not-available 0/0/2/0.16.0 ldev: 7 HPC1553A configured not-available 0/0/2/0.6.0 ldev: 10 JOBTAPE_ID configured not-available 0/0/2/0.17.0 ldev: 20 C1099A configured available 0/0/4/1.0 ldev: 21 C1099A configured available 0/0/4/1.1 ldev: 22 HPA2998A configured available 0/0/4/1.2 ldev: 30 LVDDISK configured not-available 0/4/0/0.2.0 ldev: 31 LVDDISK configured not-available 0/4/0/0.0.0 ldev: 40 LVDDISK configured not-available 0/6/2/0.2.0 ldev: 41 LVDDISK configured not-available 0/6/2/0.0.0 ldev: 501 HPTCPJD configured not-available NONE ldev: 502 HPTCPJD configured not-available NONE ldev: 503 HPTCPJD configured not-available NONE ldev: 504 HPTCPJD configured not-available NONE ldev: 505 HPTCPJD configured not-available NONE ldev: 506 HPTCPJD configured not-available NONE ldev: 507 HPTCPJD configured not-available NONE ldev: 508 HPTCPJD configured not-available NONE ldev: 509 HPTCPJD configured not-available NONE ldev: 510 HPTCPJD configured not-available NONE ldev: 511 HPTCPJD configured not-available NONE ldev: 512 HPTCPJD configured not-available NONE ldev: 513 HPTCPJD configured not-available NONE ldev: 514 HPTCPJD configured not-available NONE ldev: 515 HPTCPJD configured not-available NONE dDMEMORY AVAILABLE FOR USE (bytes)d@: 3221225472 Entering - Mount all volumes Mounting MASTER on LDEV 1 dJ Warning d@ - Volume is not available for mounting. The ldev is 2 dJ Warning d@ - Volume is not available for mounting. The ldev is 31 dJ Warning d@ - Volume is not available for mounting. The ldev is 30 dJ Warning d@ - Volume is not available for mounting. The ldev is 41 dJ Warning d@ - Volume is not available for mounting. The ldev is 40 USERLOG RECOVERY COMPLETED for MPEXL_SYSTEM_VOLUME_SET NO PARALLEL PROCESSES FOR MOUNT_ALL_VOLUMES -- Time spent in MOUNT_ALL_VOLUMES -> 0 Leaving - Mount all volumes The current boot command has been saved on the system master. NMLG FILE NUMBER 121 ON. 15:47/28/DCC STARTUP - ENTER - version C0600000 compiled 010918 15:47/28/ WARNING: I/O config from last START NORECOVERY will be used. (DCCWARN =100) 15:47/35/DCC ERROR 15-13, Configuration file not validated, status ED0F00C7. ( DCCERR=24 15:47/28/DCC STARTUP - ERROR [LAN_DUMP_SURR] Version A.00.75.003, PIN: #36 [PSI_DUMP_SURR] Version A.00.75.003, PIN: #37 [PBT_DUMP_SURR] Version A.00.75.002, PIN: #38 [ACC_DUMP_SURR] Version A.00.75.0A0, PIN: #39 System State: Initializing Mode. Reply Information Table has been initialized! System State: Multiuser Mode. 15:47/43/The system has finished rebuilding the output spoolfile directory. 15:47/45/Output spooler, LDEV #501: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/46/Output spooler, LDEV #502: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/48/Output spooler, LDEV #504: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/47/Output spooler, LDEV #503: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/46/Output spooler, LDEV #502: Stopped. 15:47/45/Output spooler, LDEV #501: Stopped. 15:47/49/Output spooler, LDEV #505: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/1/Spooling of initially spooled devices is complete. 15:47/1/Set-up of Spooling Subsystem is complete. 15:47/48/Output spooler, LDEV #504: Stopped. 15:47/47/Output spooler, LDEV #503: Stopped. 15:47/49/Output spooler, LDEV #505: Stopped. SYSTEM LOG FILE #134 IS ON 15:47/43/Output spooler, LDEV #507: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/50/Output spooler, LDEV #506: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/43/Output spooler, LDEV #507: Stopped. 15:47/50/Output spooler, LDEV #506: Stopped. Initializing Job & Session SESSION Scheduling Initialized Startup processing has begun. ============================================================== STARTUP startup block processing ============================================================== limit 100,200 15:47/52/Output spooler, LDEV #509: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 jobfence 6 15:47/52/Output spooler, LDEV #509: Stopped. outfence6 15:47/51/Output spooler, LDEV #508: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 startspool lp 15:47/51/Output spooler, LDEV #508: Stopped. JOB Scheduling Initialized startspool 6 15:47/53/Output spooler, LDEV #510: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 Device is already spooled out. (CIERR 3218) headoff LP 15:47/53/Output spooler, LDEV #510: Stopped. headoff 6 streams 10 outfence13;ldev=6 spooler lp;start Device <Unknown> is already spooled. (CIWARN 4605) 15:47/54/Output spooler, LDEV #511: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 openq lp streams 10 STREAM JPSMON.PRED.SYS 15:47/55/Output spooler, LDEV #512: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/54/Output spooler, LDEV #511: Stopped. 15:47/55/Output spooler, LDEV #512: Stopped. 15:47/56/Output spooler, LDEV #513: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/56/Output spooler, LDEV #513: Stopped. #J8 STREAM JINETD.NET.SYS 00104000 Invalid character in MPE file name. (CIERR 583) STREAM JNETSTRT.PUB.SYS 00105000 Invalid character in MPE file name. (CIERR 583) Startup processing is complete. Initiate Operator Log On 15:47/57/Output spooler, LDEV #514: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/57/Output spooler, LDEV #514: Stopped. 15:47/58/Output spooler, LDEV #515: Unable to open network printer configuration file NPCONFIG.PUB.SYS. Native Mode Spooler message 9623 15:47/58/Output spooler, LDEV #515: Stopped. 15:47/#J8/48/LOGON FOR: "PSMOND,PREDMON.SYS,PRED" ON LDEV #10. 15:47/#J8/50/FROM/PREDMON.SYS/ 15:47/#J8/50/FROM/PREDMON.SYS/JPSMON.PRED.SYS checking if Predictive libraries 15:47/#J8/50/FROM/PREDMON.SYS/are up to date.... 15:47/#J8/50/FROM/PREDMON.SYS/ 15:47/#J8/50/FROM/PREDMON.SYS/ 15:47/#J8/50/FROM/PREDMON.SYS/JPSMON.PRED.SYS checking if Predictive libraries 15:47/#J8/50/FROM/PREDMON.SYS/are up to date.... 15:47/#J8/50/FROM/PREDMON.SYS/ Successfully launched Optical Media Manager process. 15:47/53/No Optical device, Optical Media Manager process terminated ENTER ACCOUNT (SYS) PASSWORD:Successfully launched diagnostic monitor process. Successfully launched System UPS Monitor process. STM system manager started 15:47/#J8/51/FROM/MANAGER.SYS/ 15:47/#J8/51/FROM/MANAGER.SYS/Skipping check/stopping of psmond.pred.sys 15:47/#J8/51/FROM/MANAGER.SYS/reason: This *is* JPSMON.PRED.SYS 15:47/#J8/51/FROM/MANAGER.SYS/ 15:47/#J8/50/FROM/PREDMON.SYS/19 of 19 Predictive libraries 15:47/#J8/50/FROM/PREDMON.SYS/are already up to date. 15:47/#J8/50/FROM/PREDMON.SYS/19 of 19 Predictive libraries 15:47/#J8/50/FROM/PREDMON.SYS/are already up to date. 15:47/#J8/50/FROM/PREDMON.SYS/ 15:47/#J8/50/FROM/PREDMON.SYS/JPSMON.PRED.SYS starting /SYS/PRED/psmond 15:47/#J8/57/Predictive Support monitor is shutting down, 15:47/#J8/57/[caused by system shutdown command or PS software 15:47/#J8/57/upgrade] [8126] 15:47/#J8/50/FROM/PREDMON.SYS/***************************************** 15:47/#J8/50/FROM/PREDMON.SYS/* ERROR starting psmond.pred.sys 15:47/#J8/50/FROM/PREDMON.SYS/* Error number -2 returned from the 15:47/#J8/50/FROM/PREDMON.SYS/* psmond call to function psipc_init 15:47/#J8/50/FROM/PREDMON.SYS/* An error occurred 1 of 1 15:47/#J8/50/FROM/PREDMON.SYS/* times that psmond startup was tried 15:47/#J8/50/FROM/PREDMON.SYS/* 15:47/#J8/50/FROM/PREDMON.SYS/* NOTE: If this error persists check 15:47/#J8/50/FROM/PREDMON.SYS/* NOTE: the status of your network 15:47/#J8/50/FROM/PREDMON.SYS/* NOTE: (netcontrol/nscontrol status) 15:47/#J8/50/FROM/PREDMON.SYS/* NOTE: and check if diagmond is 15:47/#J8/50/FROM/PREDMON.SYS/* NOTE: running (:SHOWPROC 1;TREE;SYSTEM) 15:47/#J8/50/FROM/PREDMON.SYS/***************************************** 15:47/#J8/50/FROM/PREDMON.SYS/ 15:47/#J8/50/FROM/PREDMON.SYS/***************************************** 15:47/#J8/50/FROM/PREDMON.SYS/* JPSMON will wait 5 minutes 15:47/#J8/50/FROM/PREDMON.SYS/* before running psmond.pred.sys again 15:47/#J8/50/FROM/PREDMON.SYS/* (this was attempt 1 of 12) 15:47/#J8/50/FROM/PREDMON.SYS/***************************************** 15:50/49/INVALID PASSWORD FOR "OPERATOR.SYS,OPERATOR" DURING LOGON ON LDEV #20. (js 65) File system error reading $STDIN. (CIERR 1807) STM system manager is waiting for networking to startup. 15:52/#J8/50/FROM/PREDMON.SYS/JPSMON.PRED.SYS starting /SYS/PRED/psmond 15:52/#J8/58/Predictive Support monitor is shutting down, 15:52/#J8/58/[caused by system shutdown command or PS software 15:52/#J8/58/upgrade] [8126] 15:52/#J8/50/FROM/PREDMON.SYS/***************************************** 15:52/#J8/50/FROM/PREDMON.SYS/* ERROR starting psmond.pred.sys 15:52/#J8/50/FROM/PREDMON.SYS/* Error number -2 returned from the 15:52/#J8/50/FROM/PREDMON.SYS/* psmond call to function psipc_init 15:52/#J8/50/FROM/PREDMON.SYS/* An error occurred 2 of 2 15:52/#J8/50/FROM/PREDMON.SYS/* times that psmond startup was tried 15:52/#J8/50/FROM/PREDMON.SYS/* 15:52/#J8/50/FROM/PREDMON.SYS/* NOTE: If this error persists check 15:52/#J8/50/FROM/PREDMON.SYS/* NOTE: the status of your network 15:52/#J8/50/FROM/PREDMON.SYS/* NOTE: (netcontrol/nscontrol status) 15:52/#J8/50/FROM/PREDMON.SYS/* NOTE: and check if diagmond is 15:52/#J8/50/FROM/PREDMON.SYS/* NOTE: running (:SHOWPROC 1;TREE;SYSTEM) 15:52/#J8/50/FROM/PREDMON.SYS/***************************************** 15:52/#J8/50/FROM/PREDMON.SYS/ 15:52/#J8/50/FROM/PREDMON.SYS/***************************************** 15:52/#J8/50/FROM/PREDMON.SYS/* JPSMON will wait 5 minutes 15:52/#J8/50/FROM/PREDMON.SYS/* before running psmond.pred.sys again 15:52/#J8/50/FROM/PREDMON.SYS/* (this was attempt 2 of 12) 15:52/#J8/50/FROM/PREDMON.SYS/***************************************** MPE/iX:hello Manager.sys ENTER ACCOUNT (SYS) PASSWORD: ENTER USER (MANAGER) PASSWORD: 15:55/#S9/49/LOGON FOR: "MANAGER.SYS,PUB" ON LDEV #20. HP3000 Release: C.75.00 User Version: C.75.00 SUN, JAN 29, 2017, 3:55 PM MPE/iX HP31900 C.45.05 Copyright Hewlett-Packard 1987. All rights reserved. :ls SPOOLID JOBNUM FILEDES PRI COPIES DEV STATE RSPFN OWNER #O7 J'6 $STDLIST 8 1 LP READY MANAGER.SYS #O9 J'8 $STDLIST 8 1 LP READY MANAGER.SYS #O13 J2 $STDLIST 8 1 LP READY MANAGER.SYS #O18 J7 $STDLIST 8 1 LP READY MANAGER.SYS #O17 J5 $STDLIST 8 1 LP READY MANAGER.SYS #O1 J'9029 $STDLIST 1 1 LP READY PREDMON.SYS #O2 J'1 $STDLIST 1 1 LP READY PREDMON.SYS #O3 J'2 $STDLIST 1 1 LP READY PREDMON.SYS #O4 J'3 $STDLIST 1 1 LP READY PREDMON.SYS #O5 J'4 $STDLIST 1 1 LP READY PREDMON.SYS #O6 J'5 $STDLIST 1 1 LP READY PREDMON.SYS #O8 J'7 $STDLIST 1 1 LP READY PREDMON.SYS #O10 J'9 $STDLIST 1 1 LP READY PREDMON.SYS #O12 J1 $STDLIST 1 1 LP READY PREDMON.SYS #O14 J3 $STDLIST 1 1 LP READY PREDMON.SYS #O15 J4 $STDLIST 1 1 LP READY PREDMON.SYS #O16 J6 $STDLIST 1 1 LP READY PREDMON.SYS #O19 J8 $STDLIST 1 1 LP CREATE PREDMON.SYS INPUT SPOOL FILES OUTPUT SPOOL FILES ACTIVE = 0; CREATE = 1; READY = 17; OPEN = 0; DEFER = 0; SELECTED = 5; READY = 0; DELPND = 0; SPSAVE = 0; PRINT = 0; XFER = 0; PROBLM = 0; TOTAL IN FILES = 0; TOTAL OUT FILES = 18; IN SECTORS = 0; OUT SECTORS = 3024; OUTFENCE = 6 OUTFENCE = 13 FOR LDEV 6 :showme USER: #S9,MANAGER.SYS,PUB (NOT IN BREAK) RELEASE: C.75.00 MPE/iX HP31900 C.45.05 USER VERSION: C.75.00 CURRENT: SUN, JAN 29, 2017, 3:56 PM LOGON: SUN, JAN 29, 2017, 3:55 PM CPU SECONDS: 0 CONNECT MINUTES: 1 $STDIN LDEV: 20 $STDLIST LDEV: 20 :dstat all LDEV-TYPE STATUS VOLUME VOLUME SET - GEN ---------- ------- ---------------------------------- 1-BD07287B4C MASTER MEMBER1 MPEXL_SYSTEM_VOLUME_SET-0 :discfree C DISCFREE A.50.01 Copyright (C) Hewlett-Packard 1992. All rights reserved. SUN, JAN 29, 2017, 3:56 PM ALL MEASUREMENTS ARE IN SECTORS. ALL PERCENTAGES ARE RELATIVE TO THE DEVICE SIZE. | Configured | In Use | Available | -----------+-------------------+-------------------+-------------------+ LDEV : 1 -- (MPEXL_SYSTEM_VOLUME_SET:MEMBER1) Device | 284527984 | 7184560 ( 3%) | 277343424 ( 97%) | Permanent | 210550704 ( 74%) | 6878544 ( 2%) | 203672160 ( 72%) | Transient | 210550704 ( 74%) | 306016 ( 0%) | 210244688 ( 74%) | TOTALS : Device | 284527984 | 7184560 ( 3%) | 277343424 ( 97%) | Permanent | 210550704 ( 74%) | 6878544 ( 2%) | 203672160 ( 72%) | Transient | 210550704 ( 74%) | 306016 ( 0%) | 210244688 ( 74%) | :shutdown system :Shutdown of operating system begins. (Shut 1) Shutdown of user processes begins. (Shut 2) Shutdown of jobs & sessions begins. (Shut 3) SOFTWARE ABORT (FSERR 32) I/O error on input. (CIERR 901) :15:58/#J8/48/LOGOFF ON LDEV #10. SESSION aborted by system management. (CIERR 6027) CPU=1. Connect=3. SUN, JAN 29, 2017, 3:58 PM. 15:58/#S9/49/LOGOFF ON LDEV #20. Spoolers notified of a shutdown. (Shut 16) 15:58/43/Output spooler, LDEV #6: Cannot open physical device. 15:58/43/Output spooler, LDEV #6: Stopped. 15:58/44/The Spooling system has been shutdown. Shutdown of system processes begins. (Shut 4) Shutdown of system managers begins. (Shut 5) Shutdown of operating system complete. (Shut 6) |