|
0-30MHz VFO & Signal Generator Short Kit Type "A" (for AD9850 DDS Module) LCD, Rotary Encoder and Mounting Kit are included
Description:
This board will control one of the small AD9850 DDS (5 volt) modules available on eBay. It supports a 16x2 line LCD display showing the operating frequency, band and step size. The frequency can be adjusted using either a rotary encoder or two push buttons. Two additional buttons are used to select the frequency band and frequency step size.
Two types of Short Kit are available type "A" and type "B"
This listing is for the type "A" short kit which includes the LCD, Rotary Encoder and Mounting Kit
(see seperate listing for short kit type "B", which does not include the LCD, Rotary Encoder and Mounting Kit)
This is a "Short" kit, which means you get
- the main controller PCB
- a pre-programed PIC micro-controller
- all the passive components, and connectors
- the Blue LCD display with backlight
- the Rotary Encoder
- mounting hardware to complete the main PCB
You need to add the following items
All Versions
New Version 3.10 Software now includes (released November 2013):
Menu system allowing setting the
- IF Frequency
- IF Offset (VFO+IF, VFO-IF and IF-VFO)
- Minimum Frequency & Maximum Frequency
- Reference Oscillator Calibration and Factory Reset
- Additional Band settings
Software specification:
- operating frequency range 0-30MHz in 1Hz-1MHz steps
- frequency setting by rotary encoder or two push buttons
- frequency band setting by push button (LOW,160M,80M,40M,30M,20M,17M,15M,12M,10M)
- frequency step setting by push button (1Hz,10Hz,100Hz,1KHz,5KHz,10KHz,100KHz,1MHz)
- full menu system for setting user defined parameters
- IF frequency and IF offset (VFO+IF, VFO-IF and IF-VFO), minimum and maximum frequency range
- restores last frequency, last band, last step size and all user settings, on power up
- 32 bit arithmetic calculations for highest accuracy
- calibration function implemented in software and factory reset
- designed to control the 20 pin plug-in AD9850 DDS 5 Volt Modules (user supplied all versions)
- designed to control a 16x2 line LCD display (user supplied kit "B")
- PIC Processor with EEPROM, software written in assembler using Microchip MPLAB
Easy assembly:
Hardware specification:
-
pcb size 85mm x 40mm
-
high quality double side pcb with solder mask and silk screen
-
pre-programed PIC16F628A micro-controller
-
on-board voltage regulator for 5v plug-in module
-
input voltage 9 to 12 volts DC (polarity protected)
All specifications subject to change without notice
Anyone who has purchase Version 2.00 or 3.00 of this kit on eBay, and would like Version 3.10 can email me for a free software upgrade (downloadable HEX file, needs a PIC programer)
New Add-On Kit (released 10 Febuary 2014) for upgrading type "B" kit to type "A" kit
Available now, an optional Add-On Kit with a back-lite 16x2 LCD, Rotary Encoder and Mounting Hardware
(see seperate listing for optional LCD & Rotary Encoder Add On Kit)
Shipping UK - Items are sent Royal Mail or DHL.
Shipping International - Items are sent "Small Packet" or DHL International. Insurance can be added if requested.
Combine your purchases and save on the shipping, please notify me at the end of your first auction that your bidding on other items, when your ready I'll combine the items into one shipment for you.
Missing or Damaged Items
We take care to pack all items appropriately, and ship stuff all over the world, so far nothing has gone missing or arrived damaged. Claims for missing/damaged items will only be entertained if buyer has requested insurance and recorded delivery. All larger or more expensive items will always be shipped pre-insured by a courier and recorded, unless specifically requested not to be by buyer.
Powered by eBay Turbo Lister
|
|
| |
|