eBay

COMPLETE HYDRONIC FLOOR HEATING CONTROL SYSTEM- ONE ZONE

Includes 123,000 BTU/hr Electro Industries Electric Boiler

All necessary 1/2 O2 PEX B or C

(2) Custom Ten Circuit Radiant Circuit Manifolds

 photo HulshoffShopMechanicalsInstalled.jpg

 photo CreditCardDiscount.png

 Take the MYSTERY out of the MECHANICAL ROOM

If you have found this eBay listing you already understand all the benefits of utilizing your new shop's concrete slab floor for space heating.  Our 13 years experience, and hundreds of systems in service have taught us to miss no details on the mechanical control system build or the on-site installation of hydronic floor heating systems. 

This eBay listing is for a complete "turn key" system.  It includes your hydronic flow control equipment, commercial electric boiler, PEX and PEX circuit manifolds.  You will be responsible for zip tying the PEX to either the rebar or rewire you are using to reinforce your slab.  Our systems are simple to install, requiring no solder sweat connections.  All plumbing connections are PEX crimp fittings or threaded copper unions.  All high and low voltage wiring comes installed and clearly identified for where any on-site connections are required.

THE BOILER IS 240V 3/PHASE AND UNDERSTAND THAT (2) 100 AMP CIRCUIT BREAKERS ARE REQUIRED.  The electric boilers are practically maintenance free.  In shops where Natural Gas is not available electric boilers offer the advantage and peace of mind of knowing you are not ever going to run out of LP gas.  Gas boilers can also be problematic in areas where dust can be an issue from farm crops, dusty nearby roads and such.

Our radiant heat panels are the perfect solution for any project: floor warming, heating, or snowmelt.  Pre-piped, pre-wired, and shop tested by trained professionals.   These panels will dramatically reduce installation time as well as virtually eliminate wiring and other start-up problems.  The only wiring required is to connect the zone thermostats to the corresponding relay terminals.  Each mechanical package is pre-wired with a 120 volt power cord.

Connecting one panel to another is as easy as turning the hex nut on the brass o-ring seal union.  Each union can withhold up to 100 psi when just slightly tightened.

Best of all, each of our hydronic panels are designed for easy system maintenance.  Each component on the panel can be easily accessed and isolated with numerous shut-off valves located on all panels.

So, don’t let your next radiant project slow you down.  Our hydronic panels are fast, easy, and guaranteed to take the mystery out of the mechanical room.

This Radiant Panel’s Specifications; 

Boiler: The boiler is not included in this listing.  The panel can/will be custom built to plumb to the boiler you intend to use.

Electronic Zone Controller: Controls up to 1 zones with installed power cord for plug in installation to your existing 120 VAC outlet.  A service on/off switch is provided.  One slab temperature sensing thermostat is provided and the controller is wired to service these thermostats.  No on-site electrical wiring is necessary except for the high voltage side of the boiler.

Circulation Pumps:   Three TACO circulation pumps installed with service shut-off valves on both sides.

Microbubble Air Remover:  TACO

Zone Ports:  Each zone port(s) is equipped with 3/4” SharkBite or PEX crimp fittings for a quick no solder connection.    Zone port(s) are equipped with shut-off valves.  Ports will be installed in whatever configuration makes your installation easier for you, i.e. up or down.

Other Features:

Auto Fill Port with Backflow Preventer, Custom Sized Expansion Tank Included, Pressure reducing valve, Temperature/ Pressure Gauge on Boiler Out Side,  Manual Glycol Fill Ports, System Drain Valve for Connection to Water Hose.  Sharkbite fittings are installed for easy copper or PEX installation.

The biggest cost of any Hot Water Radiant Heat System is the labor to build and install.  Due to the special requirements of Radiant Heating Systems local plumbers and heating companies are often not familiar with the specifics of system builds.  We take the guesswork out of system builds utilizing our skilled Engineers and system builders.   You know what your costs are going to be upfront.  We custom design each and every radiant heat boiler panel system to your specific system requirements.  If this particular unit does not meet your needs we can custom build a panel specifically to your requirements.

 photo TACOProFlowDYBWLogo.png

 photo TACODYBWWinner.jpg

 photo Logowithinformation.png

 photo EmailAddressPhoto.png