EVAPO-RUST® DISTACCANTE SELETTIVO DELLA RUGGINE A BASE ACQUA
PER FERRO, ACCIAIO, GHISA E CROMATURE MADE IN U.S.A. TOTALE DA PAGARE: n° 1 X
5 Lt. EVAPO-RUST® Ü NAZIONALE: EUR 52,68 = EUR 37,50 (n° 1 x 5 Lt. EVAPO-RUST®) + EUR 5,68 (spedizione) + EUR 9,50 (IVA) Ü CALABRIA/SICILIA: EUR 54,90 = 37,50 (n° 1 x 5 Lt. EVAPO-RUST®) + EUR 7,50 (spedizione) + EUR 9,90 (IVA) Ü SARDEGNA: EUR 57,34 = 37,50 (n° 1 x 5 Lt. EVAPO-RUST®) + EUR 9,90 (spedizione) + EUR 10,34 (IVA) n° 2 X 5 Lt. EVAPO-RUST® (PROMOZIONE DISPONIBILE SOLO SU www.envirem.it) Ü NAZIONALE: EUR 92,33 = EUR 70,00 (n° 2 x 5 Lt. EVAPO-RUST®) + EUR 5,68 (spedizione) + EUR 16,65 (IVA) Ü CALABRIA/SICILIA: EUR 94,55 = EUR 70,00 (n° 2 x 5 Lt. EVAPO-RUST®) + EUR 7,50 (spedizione) + EUR 17,05 (IVA) Ü SARDEGNA: EUR 97,48 = EUR 70,00 (n° 2 x 5 Lt. EVAPO-RUST®) + EUR 9,90 (spedizione) + EUR 17,58 (IVA) N.B.: a. in contrassegno
aggiungi EUR 3,17 ai prezzi sopra riportati b. sono previsti oneri
aggiuntivi per le seguenti destinazioni: Isole Minori/Venezia
Lido/Livigno/Campione Di Italia/Altre Zone Franche FEEDBACK: https://www.facebook.com/evaporust.italia1 http://feedback.ebay.it/ws/eBayISAPI.dll?ViewFeedback2&userid=envirem-italia&ftab=AllFeedback www.envirem.it/pdf/Evapo-rust.pdf http://mondo50cc.forumfree.it/?t=67039031&st=45 http://www.mx5passionroma.it/forum/forum_posts.asp?TID=4319&PID=81695 http://www.armichepassione.com/forum/viewtopic.php?f=10&t=50&start=120 http://metaldetector.forumfree.it/?t=55729651 http://metaldetector.forumfree.it/?t=66974913 http://miles.forumcommunity.net/?t=20495564&st=30 http://www.blitzkriegmilitaria-forum.com/showthread.php?p=261944 http://forum.fuoristrada.it/messages/18477/532639.html http://spiderveloce.wordpress.com/2011/04/25/evapo-rust-mantine-le-promesse http://www.vespaforever.net/forum/topic.asp?TOPIC_ID=24130&whichpage=1 http://elaborare.info/forum/vbulletin/showthread.php?t=293748&page=2
http://www.tuttomaggiolino.it/viewtopic.php?p=375495&sid=5c2e1546d66f360dd4df644b698c5d8d
http://www.vespaforever.net/forum/topic.asp?TOPIC_ID=24234
EFFICACE: utilizzato dalla U.S.Navy,
U.S.Air Force, U.S.Army, NATO, CIA, FBI e raccomandato dalla NRA Gunsmithing School, EVAPO-RUST® rimuove
selettivamente anche gli strati più consistenti di ruggine su acciaio, ferro,
ghisa e cromature. Anche rivestimenti superficiali quali bruniture,
parkerizzazioni, bluing e fosfato di zinco verranno rimossi in circa 30
minuti. EVAPO-RUST® è l'ideale per la rimozione della ruggine perché: a.
rispetto ai tradizionali
decapanti a base acida salvaguarda tutto lo spessore metallico non ossidato
grazie alla propria azione chelante selettiva, senza richiedere né la
sorveglianza periodica della soluzione decapante per evitare che vada a
corrodere anche il metallo non ossidato sottostante la patina di ruggine, né la
neutralizzazione dell'acido post-decapaggio.
A maggior ragione in caso di patina di ruggine non estesa all'intera
superficie del metallo, con conseguente inevitabile corrosione delle parti
metalliche non ossidate a contatto con l'acido. b.
rispetto ai convertitori evita il
pericolo, soprattutto in caso di inspessimenti locali, che lo strato di
conversione non riesca ad estendersi all'intero spessore ossidato, cioè che
rimanga uno strato di ruggine residuale compreso tra lo strato di conversione
superficiale ed il substrato metallico non ossidato sottostante. c.
rispetto sia ai decapanti a base
acida, sia ai convertitori/fosfatanti minimizza l'infragilimento strutturale
del metallo causato dalla introduzione accidentale di idrogeno nel reticolo
cristallino (hydrogen embrittlement). AZIONE SELETTIVA: l'agente
chelante selettivo contenuto nella formula chimica del preparato rimuove
esclusivamente (selettivamente) lo strato ossidato (ruggine), senza asportare
e/o danneggiare il substrato metallico non ossidato. ECONOMICO: si presta a più cicli di
riutilizzo, prima dello smaltimento finale della soluzione esausta secondo le
prescrizioni di legge. N° 1 Lt. di EVAPO-RUST® rimuove fino a
60 gr. di ruggine anidra (se venduto con il marchio registrato EVAPO-RUST®). SICURO: Ü non
infiammabile, non tossico e/o nocivo, non corrosivo, non irrita la pelle e gli
occhi, non sensibilizzante per la pelle Ü non produce fumi, odori
sgradevoli, Composti Organici Volatili (COV) Ü non contiene acidi, alcali o
sostanze pericolose ai sensi Annex I, 2004/73/EC Ü biodegradabile e 100%
idrosolubile FACILE: nessuna attrezzatura speciale. Non applicabile a pennello (a meno che
l’utilizzatore finale abbia la pazienza di continuare ad applicare EVAPO-RUST® a pennello sul pezzo
arrugginito fino alla completa rimozione dell’ossido; fattibile solo per patine
di ossido molto sottili). INIBITORE
DELLA OSSIDAZIONE: dopo il
trattamento, il pezzo dovrà essere sottoposto a risciacquo con acqua prima di
qualsiasi ulteriore trattamento (es.: fosfatazione, verniciatura, applicazione
di rivestimenti e/o protettivi, etc.). Altrimenti, in assenza della fase
finale di risciacquo con acqua, EVAPO-RUST® evaporando lascerà sulla
superficie del pezzo un sottile film protettivo capace di inibire l'ossidazione
a breve termine fino a 2 settimane massimo, in funzione dell'umidità ambientale
presente (solo per stoccaggio al chiuso). BASE-ACQUA (PH = 6.1): non è
corrosivo e non danneggia ottone, rame, alluminio, oro, piombo, titanio,
acciaio, ghisa, cromo, saldature, vinile, plastica, neoprene, silicone, vetro,
sughero o legno. Uniche
incompatibilità sono cadmio e relative leghe (es.: vernici, stabilizzanti,
cadmiatura, etc.) e magnesio e relative leghe (es.: zama). L'acciaio ad alto tenore di carbonio diventa scuro a contatto con EVAPO-RUST®; il carbonio potrà essere parzialmente rimosso in fase di risciacquo con
acqua strofinando, ad esempio, con un panno. Si consiglia di immergere
completamente l’oggetto metallico da decapare perché, in caso di immersione
solo parziale, alcuni pezzi possono presentare una linea scura in
corrispondenza dell’interfaccia aria/liquido. FORMATI: 1 Litro, 5
Litri, 25 Litri; 220 Litri; 1000 Litri. SERBATOI: ideale per il ricondizionamento
dell’interno dei serbatoi grazie sia all’azione chelante selettiva che
salvaguarda tutto lo spessore metallico non ossidato, prevenendo l’eccessivo
assottigliamento della lamiera, sia alla formula a base acqua che minimizza
l’indebolimento strutturale del metallo (hydrogen embrittlement)
post-decapaggio (es.: vibrazioni, risonanze, etc.). Non serve riempire il serbatoio
di materiale abrasivo (es.: viti, bulloni, graniglia varia, etc.): basta
garantire la sufficiente tempistica di contatto con il metallo ed EVAPO-RUST® solubilizzerà
tutta la ruggine presente fermandosi automaticamente all’interfaccia con il
sottostante metallo non ossidato. A differenza degli acidi non
sottrarrà metallo non ossidato allo spessore della lamiera, garantendo, inoltre,
la compatibilità con guarnizioni (es.: rubinetto benzina) o parti metalliche
non ferrose (es.: cromature) eventualmente a contatto. La procedura operativa consigliata è la seguente: 1.
dopo aver svuotato il
carburante, lubrificante, etc. residuale eventualmente ancora presente,
collocare il serbatoio all’interno di una vasca di raccolta di capacità
superiore al volume di EVAPO-RUST®
utilizzato per il trattamento, al fine di garantire la raccolta dell'eventuale
liquido fuoriuscito in caso di ruggine passante e/o fuoriuscita accidentale 2.
se all’interno del
serbatoio, oltre alla ruggine, è presente anche del deposito organico e/o
inorganico, pulizia preliminare con idoneo detergente/sgrassante e/o
disincrostante 3.
dopo aver chiuso e
verificato la tenuta di tutte le aperture del serbatoio (tappo di rifornimento,
rubinetto benzina, sfiato), versare EVAPO-RUST® direttamente dentro il
serbatoio: a.
in caso di serbatoio
ancora installato sul telaio, il volume di EVAPO-RUST®
introdotto dovrà essere sufficiente a mandare in sommersione tutta
la lamiera arrugginita b.
in caso di serbatoio
disinstallato dal telaio, il volume di EVAPO-RUST®
introdotto potrà essere minore e dipenderà sia dal quantitativo effettivo di
ruggine da rimuovere, sia dal numero di successive rotazioni del serbatoio che
l’utilizzatore finale vorrà eseguire: infatti, più sarà elevato il volume di EVAPO-RUST®
utilizzato, minore sarà il numero di rotazioni consecutive necessarie
per mandare in sommersione tutta la superficie interna arrugginita e
viceversa. Non occorre ruotare in
continuo (es.: tipo girarrosto) il serbatoio: basta lasciarlo fermo per il
tempo necessario per la rimozione dell’ossido.
Prima di procedere con la rotazione successiva, per il trattamento di
quelle zone difficilmente ispezionabili visivamente, si consiglia di prolungare
la durata del trattamento fino alla tempistica massima pari a 24/48 ore (solo
se EVAPO-RUST® non viene diluito,
altrimenti la tempistica massima sarà progressivamente maggiore in funzione del
grado di diluizione effettivamente adottato). In entrambi i
casi, in presenza di inspessimenti di ossido, periodicamente occorrerà agitare
energicamente l’intero serbatoio contenente all’interno EVAPO-RUST®: infatti, essendo la struttura della
ruggine intrinsecamente porosa, possono prodursi frammenti di metallo solo
parzialmente arrugginiti esternamente (e come tali non completamente
solubilizzati grazie all’azione chelante selettiva propria di EVAPO-RUST®) che, sebbene già staccati dal
substrato sottostante ancora arrugginito, possono rimanere intrappolati nelle
asperità dello stesso; se lasciati in posto, i punti di contatto tra questi
frammenti metallici non più arrugginiti e il substrato metallico ancora
arrugginito non permettono l’accesso del liquido e quindi il trattamento. 4.
Una volta rimossa
completamente la ruggine all'interno del serbatoio, abbiamo n° 2 scelte
alternative: a. serbatoio di pronto utilizzo: ü svuotare completamente il serbatoio e risciacquare bene
con acqua ü immediatamente dopo il risciacquo con acqua, per
prevenire la ricomparsa di ruggine, asciugare velocemente ed accuratamente con
aria compressa ü immediatamente dopo l'asciugatura fare il pieno di
carburante b. serbatoio da sottoporre a successiva lavorazione (es.:
resinatura): ü svuotare il serbatoio senza sciacquare con acqua per
sfruttare EVAPO-RUST® anche come
protettivo anticorrosivo interoperazionale; se la successiva lavorazione verrà
eseguita dopo 10/14 gg. dal termine del decapaggio occorrerà ripristinare la protezione
bagnando nuovamente l'interno del serbatoio con EVAPO-RUST®
per ricominciare un nuovo ciclo di protezione di 10/14 gg. ü immediatamente prima della lavorazione successiva
risciacquare bene con acqua ü immediatamente dopo il risciacquo con acqua, per
prevenire la ricomparsa di ruggine, asciugare velocemente ed accuratamente con
aria compressa ü immediatamente dopo l'asciugatura eseguire la lavorazione
successiva CIRCUITO DI
RAFFREDDAMENTO MOTORE: EVAPO-RUST® è estremamente efficace anche per decapare selettivamente i condotti del
circuito di raffreddamento dei veicoli; diversamente risulterà inefficace sulle
parti in lega leggera, o in presenza di depositi minerali (es.: calcare) di
ricopertura dell’ossido. La procedura
consigliata è la seguente: 1.
svuotare il circuito di raffreddamento e sciacquarlo con acqua 2.
riempire il circuito con EVAPO-RUST® (pronto-uso non diluito) 3.
accendere il motore al minimo per qualche minuto; spegnere e lasciarlo
fermo per almeno una notte 4.
svuotare il circuito raccogliendo EVAPO-RUST® per eventuale uso futuro 5.
se necessario ripetere il processo da 1 a 5 volte 6.
al termine, una volta rimosso tutto l’ossido, riempire con il liquido
refrigerante DILUIZIONE: EVAPO-RUST®, pur tollerando ulteriori significative
percentuali di diluizione con acqua rispetto quanto da noi venduto pronto-uso,
viene fornito con un contenuto di acqua esattamente conforme alle specifiche
del produttore U.S.A.. ENVIREM S.R.L. importa il
principio attivo EVAPO-RUST® (made in USA) e lo miscela con
acqua (made in Italy). Distribuendo EVAPO-RUST® con il marchio originale, siamo
conseguentemente obbligati a rispettare scrupolosamente la percentuale di
diluizione prescritta. Venduto pronto-uso con il marchio registrato EVAPO-RUST® significa garantire al cliente un
consumo massimo pari a 60 gr. di ruggine anidra per litro. L’ulteriore diluizione con acqua, rispetto quanto da
noi venduto pronto uso, non comporta alcun vantaggio significativo: 1.
il grado di
saturazione del principio attivo contenuto nella formula, a cui corrisponde il
quantitativo di ruggine complessivamente rimovibile (cioé il consumo), rimane
esattamente identico, indipendentemente dal grado di diluizione effettivamente
adottato, pari ad un massimo di 60 gr. di ruggine anidra per litro di EVAPO-RUST®. 2.
la tempistica per il
completamento del decapaggio si dilunga significativamente all’aumentare del
grado di diluizione con acqua, quindi la tempistica massima pari a 24/48 ore
dell’EVAPO-RUST® pronto-uso non sarà più
indicativa e sarà compito dell’utilizzatore finale valutare quando il
decapaggio sarà effettivamente terminato; a tal fine, per evitare
l’eccessivo rallentamento della reazione chimica, si raccomanda di non diluire
oltre il rapporto 1 : 1 (es.: 1 Lt. EVAPO-RUST® + 1 Lt. acqua). COME FUNZIONA: STEP 1) azione chelante selettiva sull’ossido da rimuovere rispetto al substrato
metallico non ossidato STEP 2) l’agente chelante selettivo cede l’ossido rimosso, con produzione di un
complesso solfato ferrico STEP 3) i medesimi agenti chelanti selettivi, una volta ceduto l'ossido rimosso,
ricominciano un nuovo ciclo di decapaggio fino al raggiungimento del substrato
non ossidato che, per essere asportato, richiederebbe un'energia chelante
superiore a quella effettivamente disponibile La maggior parte degli agenti chelanti lega molti metalli differenti;
l'ingrediente attivo (agente chelante selettivo) contenuto nella formula
chimica di EVAPO-RUST® lega esclusivamente il ferro ossidato (ruggine),
perché non ha energia sufficiente per rimuovere il ferro non ossidato legato
molto più fortemente al substrato. TEMPERATURA MINIMA DI
UTILIZZO: poiché la
reazione chimica che determina il decapaggio selettivo della ruggine è
endotermica, cioè assorbe energia (calore) dall’ambiente esterno, è
raccomandabile utilizzare EVAPO-RUST® ad una temperatura
della soluzione superiore a 15°C. A temperature inferiori ai 5°C la reazione chimica risulta fortemente
ritardata. Nell’intervallo compreso tra
15°C e 20°C la reazione risulta relativamente veloce; mentre la massima
velocità si registra nell’intervallo compreso tra 35°C e 50°C. INCOMPATIBILITÀ CON
ALTRI MATERIALI: le incompatibilità (macchie irreversibili sul metallo) fino ad ora
accertate sono n° 2: 1.
magnesio e relative leghe (es.:
copri-carter, zama (carburatori, pompe iniezione, etc.)) 2.
cadmio e relative leghe (es.:
cadmiature (“tropicalizzazioni”); vernici al cadmio, etc.) Inoltre, alcuni pezzi possono presentare una pellicola
nera sulla parte trattata con EVAPO-RUST®:
il nero è il carbonio dell'acciaio; l'acciaio ad alto tenore di carbonio viene
generalmente utilizzato per conferire flessibilità ai pezzi finiti (es.: molle,
lamiere di taglio, etc.). I pezzi
composti da acciaio ad alto tenore di carbonio, una volta trattati con EVAPO-RUST®, presenteranno una colorazione più
scura; il carbonio può essere parzialmente
rimosso strofinando, ad esempio, con un panno sciacquando contemporaneamente
con acqua. Non è corrosivo e non danneggia ottone, rame, alluminio, oro, piombo, titanio,
acciaio, ghisa, cromo, saldature, vinile, plastica, neoprene, silicone, vetro,
sughero o legno. EVAPO-RUST® rimuoverà rivestimenti
superficiali quali bruniture, bluing,
parkerizzazioni e fosfato di zinco in circa 30 minuti (il tipo di ossidi di ferro
intaccati sono: Maghemite - γFe2O3,
Magnetite - Fe3O4 , Wustite – FeO, Idrossido di Ferro -
Fe(OH)2 , Tri-Idrossido di Ferro (Bernalite) – Fe(OH)3,
Akageneite - β FeOOH, Feroxite - δ FeOOH, Lepidocrocite - γ FeOOH 11 e
parkerizzazioni (entrambi i tipi: manganese & zinco); diversamente, Ematite
- α Fe2O3 e Goethite - α FeOOH non sono intaccati da EVAPO-RUST®).
Le anodizzazioni, invece, non verranno rimosse. Nemmeno vernici e pitture in polvere
verranno rimosse, a meno che non siano a base di ossidi. Non si verificherà alcuno stress negativo nel metallo dopo il trattamento
con EVAPO-RUST®; l’unica variazione
negativa sarà eventualmente dovuta all’attacco della ruggine causato prima del
decapaggio. In
caso di inspessimenti locali della patina di ruggine, al termine del decapaggio
rimarrà localmente il vuoto per ammanco di materiale (“camolature”). STOCCAGGIO: EVAPO-RUST® risulta estremamente economico
nell'utilizzo: a causa della bassissima concentrazione di Composti Organici
Volatili (COV) e della propria capacità chelante selettiva inalterabile per
molto tempo, si presta facilmente al riutilizzo; essendo a base d’acqua, solo
tale aliquota sarà persa per evaporazione. EVAPO-RUST® ha una durata illimitata se conservato entro la sua
confezione originaria ermeticamente sigillata.
Una volta utilizzato, la durata varia in funzione del tasso di
biodegradabilità specifico determinato dai batteri presenti sul metallo oggetto
di trattamento che vengono a contatto con EVAPO-RUST®. Negli
intervalli di tempo compresi tra i vari cicli di riutilizzo, è raccomandabile
coprire non ermeticamente la soluzione distaccante, al fine di limitare sia
l’evaporazione, sia la proliferazione dei batteri anaerobici: infatti,
versare nuovamente EVAPO-RUST® entro il
contenitore chiuso con il tappo a vite determina la moltiplicazione dei
consorzi batterici anaerobici responsabili della biodegradazione. Applicazioni pratiche hanno dimostrato
l’efficacia del EVAPO-RUST® fino ad un
periodo massimo di 12 mesi dalla data di primo utilizzo. L’acqua contenuta nella formulazione del EVAPO-RUST®
è l’unica componente che può evaporare.
Se l’aliquota di acqua persa per evaporazione viene ripristinata, la
soluzione di EVAPO-RUST® risulterà
rivitalizzata. Pertanto, prima
dell’uso, suggeriamo di apporre sul contenitore un segno in corrispondenza
dell’interfaccia con l’aria per registrare il livello massimo; successivamente,
occorrerà mantenere tale livello aggiungendo periodicamente acqua per
ripristinare l’aliquota persa per evaporazione. SMALTIMENTO: EVAPO-RUST® andrà utilizzato ad oltranza fintanto che risulterà efficace nella
rimozione dell’ossido; dopodiché la soluzione di EVAPO-RUST® diventerà esausta. Oltre
alla verifica visiva basata sull’efficacia prestazionale, esiste un metodo
empirico per verificare quando EVAPO-RUST® diventa esausto mediante la quantificazione della perdita in peso subita
dal pezzo trattato, cioè pesando il pezzo metallico oggetto di trattamento sia
prima (ma dopo la pulizia preliminare), sia dopo il decapaggio: infatti,
sapendo che n° 1 litro di EVAPO-RUST® rimuove fino a 60 gr di ruggine anidra, se ad esempio
si utilizza una soluzione di 5 Lt., cioè con consumo effettivo fino a 60 gr/Lt.
x 5 Lt. = 300 gr., l’utilizzatore avrà una stima del consumo massimo. In
caso di necessità di smaltimento antecedentemente al primo utilizzo, EVAPO-RUST® costituisce un rifiuto speciale; dopo il primo utilizzo, il substrato
organico e/o inorganico rimosso può alterare significativamente la composizione
chimico-fisica della soluzione distaccante; in ogni caso, si raccomanda di
smaltire il prodotto, esausto o meno, nonché, se necessario, anche la soluzione
acquosa di lavaggio, presso un punto di raccolta autorizzato di rifiuti
speciali o pericolosi, in accordo con le prescrizioni di legge vigenti. 1. METODO AD IMMERSIONE o
RIEMPIMENTO PULIZIA PRELIMINARE: rimozione dell’eventuale strato organico e/o inorganico superficiale di
copertura della patina di ruggine con idoneo detergente/sgrassante e/o
disincrostante. IMMERSIONE/RIEMPIMENTO: immergere in vasca o
riempire (es.: serbatoio, filetto cieco, etc.) l’oggetto metallico da
decapare per almeno 30 minuti in caso di patina sottile; fino a 24/48 ore per
le patine di ruggine più consistenti.
Se EVAPO-RUST®
viene
diluito con acqua, la predetta tempistica non è più indicativa perché aumenta
progressivamente in funzione del grado di diluizione effettivamente
adottato. Per evitare l’eccessivo
rallentamento della reazione chimica, si raccomanda di non diluire oltre il rapporto
1:1 (es.: 1 Lt. EVAPO-RUST® + 1 Lt. acqua). Anche se diluito, il consumo rimane
invariato: 1 Lt. di EVAPO-RUST® rimuove fino a 60
gr. di ruggine anidra. Si
consiglia di immergere completamente l’oggetto metallico da decapare perché, in
caso di immersione solo parziale, alcuni pezzi possono presentare una linea
scura in corrispondenza dell’interfaccia aria/liquido. N.B.: solo in caso di inspessimenti
locali di ruggine è indispensabile che l’oggetto metallico
da decapare venga periodicamente (ogni 6/12 ore): a.
sciacquato con acqua nelle zone
arrugginite, oppure b.
spazzolato nelle zone
arrugginite, oppure c.
nel caso del ricondizionamento
dell’interno di un serbatoio dare un’energica agitata dell’intero serbatoio e
della soluzione di EVAPO-RUST® contenuta. Infatti,
essendo la struttura della ruggine intrinsecamente porosa, possono prodursi frammenti di
metallo solo parzialmente arrugginiti esternamente (e come tali non
completamente solubilizzati grazie all’azione chelante selettiva propria di EVAPO-RUST®) che, sebbene
già staccati dal substrato sottostante ancora arrugginito, possono rimanere
intrappolati nelle asperità dello stesso; se lasciati in posto, i punti di
contatto tra questi frammenti metallici non più arrugginiti e il substrato
metallico ancora arrugginito non permettono l’accesso del liquido e quindi il
trattamento. POST-TRATTAMENTO: terminato il decapaggio, il pezzo dovrà essere sottoposto a risciacquo con
acqua prima di qualsiasi ulteriore trattamento (es.: fosfatazione,
verniciatura, cromatura, protettivi, rifornimento carburante, etc.). In assenza della fase finale di risciacquo
con acqua, EVAPO-RUST® evaporando lascerà sulla
superficie del pezzo un sottile film protettivo anticorrosivo capace di inibire
l’ossidazione a breve termine fino a 2 settimane al massimo. 2. METODO AD ULTRASUONI Accelera notevolmente la velocità di decapaggio grazie alla tecnologia ad
ultrasuoni comunemente utilizzata nelle applicazioni industriali; inoltre, in
caso di patina di ruggine consistente, non richiede la fase intermedia di risciacquo o spazzolatura sopraddetta. PULIZIA PRELIMINARE: vedi metodo precedente. LAVAGGIO: riempire la lavatrice ad ultrasuoni con una quantità sufficiente di EVAPO-RUST® per raggiungere il livello indicato dal costruttore; immergere il pezzo da trattare ed
avviare il programma di lavaggio. La
durata dell’applicazione dipenderà dallo spessore della ruggine da rimuovere:
per patine sottili impiega circa 1 minuto, mentre per le patine più consistenti
circa 1 ora. È la modalità di
applicazione più veloce per rimuovere la ruggine. POST-TRATTAMENTO: vedi metodo precedente. 3. METODO A SPRUZZO PULIZIA PRELIMINARE: vedi metodo precedente. SPRUZZO: predisporre una vasca di raccolta del percolato contenente una pompa
sommersa o autoadescante di ricircolo collegata con uno spruzzatore. Riempire la vasca con una
quantità sufficiente di EVAPO-RUST® per
garantire sia il pescaggio della pompa, sia il riempimento della tubazione di
mandata. Si consiglia di limitare la portata di
ricircolo per minimizzare la produzione di schiuma. Spruzzare EVAPO-RUST®
direttamente sulla superficie arrugginita garantendo un tempo di contatto tra EVAPO-RUST® e la ruggine pari ad almeno 30 minuti in caso
di patina sottile; fino a 24/48 ore per le patine di ruggine più consistenti. N.B.: solo in caso di inspessimenti
locali di ruggine è indispensabile che l’oggetto metallico
da decapare venga periodicamente (ogni 6/12 ore): a.
sciacquato con acqua nelle zone arrugginite, oppure b.
spazzolato nelle zone arrugginite. Infatti,
essendo la struttura della ruggine intrinsecamente porosa, possono prodursi frammenti di
metallo solo parzialmente arrugginiti esternamente (e come tali non
completamente solubilizzati grazie all’azione chelante selettiva propria di EVAPO-RUST®) che, sebbene
già staccati dal substrato sottostante ancora arrugginito, possono rimanere
intrappolati nelle asperità dello stesso; se lasciati in posto, i punti di
contatto tra questi frammenti metallici non più arrugginiti e il substrato
metallico ancora arrugginito non permettono l’accesso del liquido e quindi il
trattamento. POST-TRATTAMENTO: vedi metodo precedente. 4. METODO AD ADESIONE PULIZIA PRELIMINARE: vedi metodo precedente. ADESIONE: suggeriamo n° 2 modalità di
applicazione alternative: a.
immergere un foglio di
carta assorbente dentro la soluzione di EVAPO-RUST®;
strizzarlo e farlo aderire contro la superficie da trattare raccogliendo
l’eventuale liquido di percolazione; oppure b.
travasare EVAPO-RUST® dentro uno spruzzatore; applicare un
foglio di carta assorbente asciutto sulla superficie arrugginita; spruzzare EVAPO-RUST® sul foglio di carta assorbente
raccogliendo tutto l’eventuale liquido di percolazione. Successivamente coprire la carta assorbente bagnata con un foglio di
plastica (es.: pellicola trasparente ad uso alimentare) per limitare
l’evaporazione della frazione acquosa. Controllare periodicamente il
progresso del decapaggio e, in caso di ruggine consistente, dare periodicamente
una leggera spazzolata al pezzo. Se
necessario ripetere l’applicazione. POST-TRATTAMENTO: vedi metodo precedente. PRE-TESTARE PRIMA
DELL’APPLICAZIONE DIRITTO
DI RECESSO: ai
sensi del D.Lgs. 206 -
06.09.2005, gli acquirenti
identificabili come consumatori, cioè qualsiasi persona fisica che, nei contratti di vendita
di beni di consumo, agisce per scopi estranei all’attività imprenditoriale e/o
professionale eventualmente svolta, potranno avvalersi del diritto di recesso, a mezzo lettera raccomandata
A.R e rispedendo il prodotto acquistato entro 10 giorni lavorativi
dalla data di ricevimento della merce, in confezione integra e sigillata ed
entro l’imballo originale, alla nostra sede: ENVIREM S.R.L. - Via Meucci, 11 -
40138 Bologna (BO) – Italia (I). La restituzione della merce rimarrà integralmente a cura ed onere del consumatore. Entro 30 giorni dalla data in cui è verremo
a conoscenza del recesso e delle Vs. coordinate bancarie (IBAN), provvederemo
alla restituzione del pagamento a mezzo bonifico bancario. MODALITA’ &
TERMINI DI SPEDIZIONE A scelta del Cliente: a. senza appuntamento: il ns. corriere convenzionato
esegue n° 2 tentativi consecutivi di consegna senza appuntamento in
orario 0830/1930 (consegna a piano terra, sabato e
festivi esclusi): il 1° tentativo il giorno lavorativo che comunicheremo a
mezzo email al Cliente con preavviso di almeno 1 giorno; il 2° tentativo il
giorno lavorativo successivo;
qualora entrambi tali tentativi andassero falliti, la merce sarà disponibile in
fermodeposito c/o la sede locale del ns. corriere convenzionato che
comunicheremo al Cliente. Dopodiché, se il Cliente provvederà direttamente al
ritiro entro 3 gg. lavorativi non ci saranno spese aggiuntive; se invece
richiederà il 3° tentativo di consegna, oppure ritirerà la merce in
fermodeposito dopo 3 gg. lavorativi dalla data di apertura del dossier
giacenza, verrà addebitato anticipatamente (a mezzo PayPal o bonifico bancario)
un sovrapprezzo pari a EUR 3,60+IVA come spese di giacenza;
trascorsi 3 gg. lavorativi dalla data di apertura del dossier giacenza
senza che il Cliente esegua il ritiro della merce in fermodeposito, la merce
ritorna a Bologna, dopodiché, per entrare in possesso della merce, dovrà essere
corrisposta anticipatamente la somma seguente: EUR 5,68+IVA (spese di rientro)
+ EUR 3,60+IVA (spese di giacenza) + EUR 5,68+IVA (spese di rispedizione); oppure b. con appuntamento: con un sovrapprezzo pari ad EUR
1,00+IVA sulle spese di spedizione sopra indicate, il Cliente verrà
contattato telefonicamente dal ns. corriere per concordare la data e l’orario
della consegna; oppure c. fermodeposito: se il Cliente non può garantire
la propria presenza, o di Suo incaricato, durante i giorni lavorativi, senza
alcun sovrapprezzo può ritirare personalmente la merce presso la sede locale
del corriere che gli comunicheremo (giorni feriali (0830/1230 – 1430/1830) -
sabato mattina (0830/1200)). MODALITA’ &
TERMINI DI PAGAMENTO A scelta del Cliente: a. contrassegno (sovrapprezzo EUR 2,60+IVA) b. PayPal c. bonifico bancario MODALITA’ &
TERMINI DI FATTURAZIONE In qualità di venditore professionale, ENVIREM S.R.L. ha l’obbligo di
fatturazione. Gli eBayers che acquistano in qualità di Consumatori (per consumatore s'intende
qualsiasi persona fisica che, nei contratti di compravendita di beni mobili di
consumo, agisce per scopi estranei all’attività imprenditoriale, commerciale,
artigianale o professionale eventualmente svolta), devono trasmettere al momento dell’acquisto
tutti i seguenti dati: 1. nome e
cognome 2. indirizzo
di residenza 3. indirizzo
di spedizione (se differente dall’indirizzo di residenza) 4. telefono
per la consegna Gli eBayers che acquistano in qualità di Professionisti (professionista s'intende
qualsiasi persona fisica o giuridica che, nei contratti di compravendita di
beni mobili di consumo, agisce nell'esercizio della propria attività
imprenditoriale, commerciale, artigianale o professionale, ovvero un suo
intermediario), devono
trasmettere al momento dell’acquisto tutti i seguenti dati: 1. denominazione sociale 2. indirizzo
sede sociale 3. indirizzo
di spedizione (se differente dall’indirizzo della sede sociale) 4. codice
fiscale & partita IVA 5. telefono
per la consegna EVAPO-RUST® WATERBASED SELECTIVE RUST
REMOVER FOR STEEL, CAST IRON AND CHROME PLATINGS MADE IN U.S.A. FREIGHT & INSURANCE ALL INCLUSIVE PRICELIST: · ANDORRA: EUR 128,10 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 134,20) · BELGIQUE: EUR 12,20 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 12,20) · BULGARIA: EUR 30,50 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 30,50) · CESKO: EUR 21,96 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 21,96) · CYPRO: EUR 103,70 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 120,78) · DANMARK: EUR 19,52 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 19,52) · DEUTSCHLAND: EUR 12,20 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 12,20) · EESTI VABARIIK/LATVIJA/LIETUVA: EUR 31,72 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 31,72) · ENGLAND/WALES: EUR 28,06 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 28,06) · SCOTLAND/NORTH IRELAND: EUR 58,56 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 58,56) · GIBRALTAR: EUR 134,20 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 146,40) · ESPAÑA: EUR 24,40 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 24,40) · ILLES BALEARS: EUR 79,30 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 91,50) · CANARIES/CEUTA/MELILLA: EUR 114,68 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 134,20) · FRANCE: EUR 24,40 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 24,40) · CORSICA: EUR 95,16 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 95,16) · GREECE: EUR 79,30 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 103,70) · GREECE ISLANDS: EUR
134,20 (n° 2 x 5 Lt. EVAPO-RUST®:
EUR 134,20) · HRVATSKA: EUR 24,40 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 24,40) · IRELAND: EUR 34,16 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 34,16) · LIECHTENSTEIN: EUR 58,56 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 58,56) · LUXEMBOURG: EUR 15,86 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 15,86) · MAGYARORSZÀG: EUR 25,62 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 25,62) · MALTA: EUR 84,18 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 108,58) · NEDERLAND: EUR 15,86 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 15,86) · NORGE: EUR 79,30 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 79,30) · ÖSTERREICH: EUR 12,20 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 12,20) · POLSKA: EUR 21,96 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 21,96) · PORTUGAL: EUR 28,06 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 28,06) · AÇORES/MADEIRA: EUR 115,90 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 128,10) · ROMANIA: EUR 30,50 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 30,50) · SCHWEIZ/SUISSE: EUR 82,96 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 82,96) · SLOVENIJA: EUR 18,30 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 18,30) · SLOVENSKO: EUR 32,94 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 32,94) · SRBIJA: EUR 87,84 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 87,84) · SUOMI: EUR 46,36 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 46,36) · SVERIGE: EUR 29,28 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 29,28) · TÜRKIYE: EUR 101,26 (n° 2 x 5 Lt. EVAPO-RUST®: EUR 101,26) The above
prices include Customs Fees for the following extra-EU destinations:
LIECHTENSTEIN - NORGE - SRBIJA - SCHWEIZ/SUISSE – TÜRKIYE. FREIGHT CHARGES FOR ITALY: n° 1 X
1 Lt. EVAPO-RUST® Ü NAZIONALE: EUR 18,52 = EUR 9,50 (n° 1 x 1 Lt. EVAPO-RUST®) + EUR 5,68 (shipping) + EUR 3,34 (VAT) Ü CALABRIA/SICILIA: EUR 20,74 = 9,50 (n° 1 x 1 Lt. EVAPO-RUST®) + EUR 7,50 (shipping) + EUR 3,74 (VAT) Ü SARDEGNA: EUR 23,67 = 9,50 (n° 1 x 1 Lt. EVAPO-RUST®) + EUR 9,90 (shipping) + EUR 4,27 (VAT) n° 2 X 1 Lt. EVAPO-RUST® (PROMOTION AVAILABLE ONLY ON www.envirem.it) Ü NAZIONALE: EUR 27,67 = EUR 17,00 (n° 2 x 1 Lt. EVAPO-RUST®) + EUR 5,68 (shipping) + EUR 4,99 (VAT) Ü CALABRIA/SICILIA: EUR 29,89 = EUR 17,00 (n° 2 x 1 Lt. EVAPO-RUST®) + EUR 7,50 (shipping) + EUR 5,39 (VAT) Ü SARDEGNA: EUR 32,82 = EUR 17,00 (n° 2 x 1 Lt. EVAPO-RUST®) + EUR 9,90 (shipping) + EUR 5,92 (VAT) N.B.: a.
cash on delivery payment (contrassegno)
available only for Italy
with an extra-cost of EUR 3,17 b. extra-costs
to the following Italian destinations: Isole Minori/Venezia
Lido/Livigno/Campione Di Italia/Altre Zone Franche FEEDBACKS: https://www.facebook.com/evaporust.italia1 http://feedback.ebay.it/ws/eBayISAPI.dll?ViewFeedback2&userid=envirem-italia&ftab=AllFeedback www.envirem.it/pdf/Evapo-rust.pdf http://mondo50cc.forumfree.it/?t=67039031&st=45 http://www.mx5passionroma.it/forum/forum_posts.asp?TID=4319&PID=81695 http://www.armichepassione.com/forum/viewtopic.php?f=10&t=50&start=120 http://metaldetector.forumfree.it/?t=55729651 http://metaldetector.forumfree.it/?t=66974913 http://miles.forumcommunity.net/?t=20495564&st=30 http://www.blitzkriegmilitaria-forum.com/showthread.php?p=261944 http://forum.fuoristrada.it/messages/18477/532639.html http://spiderveloce.wordpress.com/2011/04/25/evapo-rust-mantine-le-promesse http://www.vespaforever.net/forum/topic.asp?TOPIC_ID=24130&whichpage=1 http://elaborare.info/forum/vbulletin/showthread.php?t=293748&page=2
http://www.tuttomaggiolino.it/viewtopic.php?p=375495&sid=5c2e1546d66f360dd4df644b698c5d8d
http://www.vespaforever.net/forum/topic.asp?TOPIC_ID=24234
OPERATIVE: utilized by the
U.S.Navy, U.S.Air Force, U.S.Army, NATO, FBI, CIA, Engine Builders, Auto
Enthusiasts, Gunsmiths, Forensic Labs, OEM's, Farmers, Antique Restorers and
recommended by the NRA Gunsmithing School, EVAPO-RUST®
removes even deep rust on all types of steel, cast iron and chrome platings. EVAPO-RUST® will remove sacrificial oxide
coatings and is perfect for removing weapon finishes such as Bluing,
Parkerizing, Zinc Phosphate, and Browning within 30 minutes. EVAPO-RUST® is perfect for removing rust
because: 1. unlike traditional acid-based
rust removers, EVAPO-RUST® does not harm the underlying
not-rusted metal, because it works through selective chelation, without any
necessity to check periodically the rust removal process, to avoid both the
underlying not-rusted metal corrosion, and the final acid neutralization. Even more so whenever the rust layer does
not extend to the whole metal surface, with unavoidable resulting corrosion of
the not-rusted metal surface in contact with the acid-based rust remover. 2. unlike rust converters, EVAPO-RUST® avoids the danger, especially in case of heavy rust,
that the rust-converted layer will not extend to the whole rust thickness; that
is, it may remain a residual rust layer between the superficial rust-converted
layer, and the underlying not-rusted metal. 3. unlike both traditional
acid-based rust removers, and rust converters, EVAPO-RUST® reduces hydrogen embrittlement following exposure to
hydrogen, which may weaken the metal structure inside. SELECTIVE RUST REMOVAL: works
through selective chelation: it can only remove iron oxide, but is too weak to
remove iron from steel because the iron is held much more strongly. CHEAP: can be
used over and over, for several cycles, before final disposal of spent solution
according to your local and national regulation concerning waste disposal. One liter removes up to 60 gr. of pure dry
rust (if sold with its trademark EVAPO-RUST®). SAFE: ·
not flammable, not toxic, not corrosive, not eye and
skin irritant or sensitizing ·
no fumes or bad odors, no Volatile Organic Compounds
(VOC) ·
no acid, caustic or hazardous substances according to
Annex I, 2004/73/EC ·
biodegradable (NOT readibily) and 100% watersoluble ·
will not harm unrusted steel, safe on other metals
will not affect plastic, PVC, Viton and most paints EASY: no
special equipment (NOT brushable,
unless the end-user will be so patient to continue brushing, until the rust removal
process completion; it can take several hours, so it is feasible only for light
rust) . OXIDATION INHIBITION: after
rust removal, the treated component can be water-rinsed for painting, plating,
or other type of corrosion protective coating.
If left unrinsed, EVAPO-RUST® will dry
on the treated surface to a hard, short-term corrosion resistant coating. As a dry film, EVAPO-RUST® inhibits oxidation indoors up
to 14 days, depending on local room-humidity & temperature and metal item
shape (the more irregular will be the shape (with high energy points), the
shorter the protection will last). WATER-BASED (PH = 6.1): is
non-corrosive to steel and does not harm brass, copper, aluminum, gold, lead,
titanium, steel, cast iron, chrome, solder points, vinyl, plastic, rubber,
silicone, glass, cork or wood.
Anodizing, Cobalt Tungsten Carbide, Powder Coating, Chrome, Nickel,
Paint, and most other coatings will not be removed as long as they do not
contain oxides. EVAPO-RUST® will not harm lead or solder
points. High carbon steel and tool
alloy steel items, when derusted, will have a darker appearance; much of the
carbon can be partially removed simply by wiping with a cloth. Some items not fully immersed for extended
periods may experience etching at the water-line. SIZES: 1 Litre, 5 Litres, 25
Litres; larger sizes on request. GASTANKS: EVAPO-RUST® is ideal for rust removal
inside gastanks because: ·
thanks to its selective action, it preserves the whole
underlying not-rusted metal, avoiding the corrosion of the underlying
not-rusted metal ·
thanks to its water-based formula, it reduces hydrogen
embrittlement following exposure to hydrogen (eg.: vibrations, resonance,
etc.). It does
not need filling the gastank with abrasive material (eg.: screws, bolts, etc.):
it will be enough to grant the minimum contact time with rust and EVAPO-RUST® will solubilize the whole
rust stopping itself automatically once reached the underlying not-rusted metal
layer. Unlike
traditional acid-based rust removers EVAPO-RUST® will not either harm
not-rusted metal, or gaskets (eg.: gasoline float valve, etc.) and not-iron
metal (eg.: aluminum, chrome platings, etc.). We
suggest the following operative procedure: 1. empty the whole residual fuel,
lubricant, etc., and then put the gastank inside a suitable tank wide enough to
collect the whole EVAPO-RUST® volume (in case of through-metal
rust) 2. in case of presence of organic
and/or inorganic deposits, first preliminary degreasing with suitable detergent
or solvent 3. close every valve (refueling tap,
gasoline float valve , air vent), and pour EVAPO-RUST® inside the gastank: a. if the gastank is still installed
on the chassis, the quantity of EVAPO-RUST® must be sufficient to submerge
the whole rusted metal surface inside b. if the gastank is not installed
on the chassis anymore, the quantity of EVAPO-RUST® may be lesser and will depend on both the effective
rust quantity to remove, and the number of progressive gastank rotations
required to submerge the whole internal rusted metal surface: indeed, the more EVAPO-RUST® you use, the lesser number of consecutive gastank
rotations will be needed. It does not need rotating uninterruptedly the gastank; it will be enough
granting the sufficient contact time. We suggest a period of 24/48 hours for each consecutive rotation,
especially when it is difficult or even impossible to check the rust removal
process from the refueling tap (only if EVAPO-RUST® will be not water-mixed, otherwise it may be needed
more than 24/48 hours, depending on the effective water-dilution ratio). In
both cases, for extremely heavy rust, periodically (every 6/12 hours) shake
energetically the gastank, together with the EVAPO-RUST® solution poured inside: indeed, being the rust
structure intrinsically porous, some metal fragments detached from the
underlying metal surface, only externally oxidized (and, as such, not fully
solubilized thanks to EVAPO-RUST® selective action) may be trapped
and still be embedded in the metal (pits, crevices); the points of contact
between detached metal fragments and underlying rusted metal asperity will
prevent EVAPO-RUST® access and, so that, any rust
removal action. 4. once finished, you have 2
possible solutions: a.
gastank ready to use: ·
empty the gastank and water rinse ·
immediately after water rinsing, in order to avoid
flush rust, quickly air-dry ·
immediately after air-drying refuel the gastank b.
gastank ready for successive
metalworking operation (eg.: application of tank liner): ·
empty the gastank without water-rinsing in order to
use EVAPO-RUST® as excellent inter-operational
metal protective (till 10/14 days indoor storage); if you need more storage
time, you will need to dip periodically the items inside EVAPO-RUST® solution every 10/14 days ·
immediately before the following metalworking
operation, accurately water-rinse the item ·
immediately after water-rinsing, in order to avoid
flush rust, quickly air-dry ·
immediately after air-drying, carry out the following
metalworking operation COOLING SYSTEM: EVAPO-RUST® is perfect to remove rust
from cooling systems; it will not harm gaskets, aluminum alloys, etc., but it
will not remove deposits such as lime, oily deposits, etc.. We
suggest the following operative procedure: 1. drain cooling system and rinse
with water 2. fill system with EVAPO-RUST® (do NOT dilute) 3. run Engine under normal
conditions, shut engine down and let sit overnight 4. drain system into a container for
later use 5. flush system with water 6. repeat process (1-5) if necessary 7. fill system with proper
coolant/antifreeze WATER-MIXING RATIO: even if
sold ready-to-use with exactly the same formulation and water content as sold
by the U.S. manufacturers, EVAPO-RUST® may be
further water diluted. We import
EVAPO-RUST® in
concentrated form (made in USA) then we mix it with water (made in Italy). As sold
with its original U.S. brand, we are legally obliged to sell EVAPO-RUST® with the exact water-mixing
ratio prescribed by the U.S. Manufacturer. That
means granting up to 60 gr. of pure dry rust for each liter of EVAPO-RUST®. Further water-mixing
is not recommended: ·
as 1 Lt. of EVAPO-RUST® removes till 60 gr. of pure dry rust, further
water-mixing does not increase the total amount of rust removed ·
the more you water-mix, the more time it needs to
complete the rust removal process In order
to avoid lowering excessively the speed of the rust removal process, do not
further water-mix beyond 1:1 ratio (eg.: 1 Lt. EVAPO-RUST® + 1 Lt. water). OPERATIVE TEMPERATURE: we
recommend to use the solution of EVAPO-RUST® at a
bath temperature above 15°C, as the chemistry is endothermic so it requires
some ambient heat to work. In
temperatures below 5°C, the reaction is severely retarded. At
15-20°C it is pleasantly quick, and at 35-50°C it is very active. In order
to speed the process, first always remove oil & greases by using dedicated
detergent prior to derusting. HOW IT WORKS: EVAPO-RUST® works at a pH of 6.1 to 7
(neutral) through selective chelation: this is a process in which a large
synthetic molecule forms a bond with metals and holds them in solution. Most
chelating agents bind many different metals; the active ingredient in EVAPO-RUST® bonds to iron exclusively. It can
remove iron from iron oxide, but is too weak to remove iron from steel because
the iron is held much more strongly. The
chelator is too expensive to use large quantities in the finished product. An
organic chemical that easily loses sulfur to form ferric sulfate was added to
remove iron from the iron-chelator complex. This
allows the chelator to remove more iron from iron oxide. The
sulfur-bearing compound is much less expensive than the chelator and makes EVAPO-RUST® economical to use. METAL INCOMPATIBILITIES: at
moment, there are only n° 2 tested metal incompatibilities: ·
cadmium and cadmium alloys (eg.: cadmium platings,
cadmium-based paints, etc.) ·
magnesium and magnesium alloys (eg.: carter,
carburetors, injection pumps, etc.) High
carbon steel and tool alloy steel items, when derusted, will have a darker
appearance after using EVAPO-RUST®. The black
is carbon from the steel. Generally
high carbon steel is used in making items that are flexible (e.g. springs, saw
blades, etc.). Much of
the carbon can be partially removed simply by wiping with a cloth. The black
film is carbon from the steel. Steel is
composed of a combination of carbon and iron. This is a
natural phenomenon that chemists refer to as carbon migration. The
carbon from the steel moves, or migrates, to the outer layer of the metal and
settles into the pores. The
removal of the rust (iron oxide) reduces the proportion of iron to carbon,
leaving a higher concentration of carbon on the outer surface. This
heavier layer of carbon could cause a darkening of the metal due to the
attributes of the carbon. The
darkening does not have an adverse affect on the metal. It merely
represents the movement of carbon from the interior of the metal to the
exterior of the metal. EVAPO-RUST® is non-corrosive to steel and
does not harm brass, copper, aluminum, gold, lead, titanium, steel, cast iron,
chrome solder points, vinyl, plastic, rubber, silicone, glass, cork, or wood. Conversely,
anodizing, powder coating, chrome, nickel, paint, and most other coatings will
not be removed as long as they do not contain oxides (the precise types of iron
oxide and coatings affected are: Maghemite - Fe2O3, Magnetite - Fe3O4 , Wustite
– FeO, Iron hydroxide - Fe(OH)2, Iron trihydroxide (bernalite) – Fe(OH)3,
Akageneite - ß FeOOH, Feroxyhite - d FeOOH, Lepidocrocite - FeOOH 11 and
Parkerizing (both types: manganese & zinc); Hematite - a Fe2O3 and Goethite
- a FeOOH are not affected by EVAPO-RUST®). EVAPO-RUST® will not harm lead or solder
points. Zinc
coatings will be removed by prolonged exposure to EVAPO-RUST®. There
will be no stress change in the metal due to treatment with EVAPO-RUST®. The only
change that will occur will be rust damage that was caused prior to any
treatment with EVAPO-RUST®. STORAGE: EVAPO-RUST® has an indefinite shelf life
and can be used over and over until it absolutely stops working; mainly water
is lost to evaporation. Shelf
life is for un-opened product; once opened, the life of the bath will vary due
to biodegradability (bacteria introduced into the solution). After
using EVAPO-RUST®, it is
better to cover the solution, but still allow air to the bath: pouring the
solution back into a sealed container will allow the anaerobic bacteria to
begin the degradation process. Used,
open baths have continued to operate for over a 12 months period. The water
content in EVAPO-RUST® is the
only thing that will evaporate. If the
water content is replaced to bring the content back to the capacity of the
original container purchased, EVAPO-RUST® will be
revitalized. It is
suggested that when using EVAPO-RUST® mark the
top of fluid level in container before use and maintain this level by continual
top up with fresh water to circumvent evaporation. DISPOSAL: The more
you derust, the blacker the solution becomes. EVAPO-RUST® is spent when it is pitch
black and no longer performs. Also the
specific gravity will change from 1.04 to 1.08 and pH from 6.1 to 7.2. Dispose
of both the water rinse solution (if necessary), and the spent (or not)
solution of EVAPO-RUST® and its
container at hazardous or special waste collection point according to your
local and national regulation concerning waste disposal. HOW TO USE IT: we
recommend 4 methods of application: 1. DIP/FILL METHOD 2. ULTRASONIC METHOD 3. SPRAY METHOD 4. WRAP METHOD You will
use the first two methods (DIP/FILL & ULTRASONIC) whenever you can submerge
the metal items inside a suitable tank or the metal items themselves may work
as tank (eg.: gastank); the others (SPRAY & WRAP) whenever the metal items
are too big to be submerged. If you
have to remove rust from wide metal items, use B547 (ASHLAND DREWCLEAN B547
bottled in 1. Lt. Jug and 5 Lt. tank). If you
have to remove oxidation and carbon deposits from aluminium and yellow alloys
(copper, brass, bronze) use C734 (ASHLAND DREWCLEAN C734 bottled in 1. Lt. Jug
and 5 Lt. tank). 1.
DIP/FILL METHOD PRELIMINARY
DEGREASING: first always remove oil & greases by using dedicated
detergent/degreaser prior to derusting. DIP/FILL: take a sufficient quantity of EVAPO-RUST® required to submerse or fill (eg.: gastanks) the
rusty object; then submerse or fill it. The duration for derusting will
depend upon the severity of rust: for flash rust removal it takes about 30
minutes and up to 24/48 hours for extremely heavy rust. Periodically check the object
during the derusting process to know the status. Some items not fully immersed for
extended periods may experience etching at the water-line. If water-mixed the above time
interval will increase: the more you water-mix, the more time it needs to
complete the rust removal process. To avoid the rust removal process
became too slow, do not further water-mix beyond 1:1 ratio (eg.: 1 Lt. EVAPO-RUST® plus 1 Lt. water). As 1 Lt. of EVAPO-RUST® removes till 60 gr. of pure dry rust, further
water-mixing does not increase the total amount of rust removed. NOTE: for extremely heavy rust,
periodically rinse item with water and/or softly brush item with a scrubbing
tool (e.g.: a wire brush): this stage is VERY important in getting the best
results because residual rust may still be embedded in the metal (pits,
crevices) after the initial soaking. AFTER-TREATMENT: after treatment, the part can be
water rinsed for painting, plating, or other type of corrosion protective
coating. It is important to always rinse
the metal after a treatment with EVAPO-RUST®: tiny molecules of iron will
still be embedded in the EVAPO-RUST® solution, and these molecules
must be rinsed off with water or they will activate the re-formation of rust on
the metal object. If left unrinsed, the fluid will
dry on the treated surface to a hard, short-term corrosion resistant coating
with no corrosion removal properties. As a dry film, it inhibits
oxidation indoors up to 14 days, depending on local room-humidity &
temperature and metal item shape (the more irregular will be the shape (with
high energy points), the shorter the protection will last). 2.
ULTRASONIC METHOD PRELIMINARY
DEGREASING: the same as the previous method. FILL: take a sufficient quantity of EVAPO-RUST® to fill the ultrasonic tank to the required level. Submerse the component and switch
on ultrasonic power. The duration for derusting will
depend upon the severity of rust: for flash rust removal it takes about a
minute and about an hour for removal of medium to sever rust. Basically this is the faster way
to remove rust. AFTER
TREATMENT:
the same as the previous method. 3.
SPRAY METHOD PRELIMINARY
DEGREASING: the same as the previous method. SPRAY: fill the sprayer tank with a
sufficient amount of EVAPO-RUST® to continually spray the rusted
object. Collect the runoff in a suitable
tank/container. Continuously spray the rusty
object about 30 minutes for flash rust removal and up to 24/48 hours for
extremely heavy rust (the rusty object must be always wetted). If there is light rust on a flat
surface area (e.g. appliances, countertops, etc.), then spraying on EVAPO-RUST® solution can work very effectively. The longer the contact time, the
better results. NOTE: for extremely heavy rust,
periodically rinse item with water and/or softly brush item with a scrubbing
tool (e.g.: a wire brush): this stage is VERY important in getting the best
results because residual rust may still be embedded in the metal (pits,
crevices) after the initial soaking. AFTER
TREATMENT:
the same as the previous method. 4.
WRAP METHOD PRELIMINARY
DEGREASING: the same as the previous method. WRAP: take a suitable size of smooth
paper towel or a fake chamois or other tightly knit material. Soak it in EVAPO-RUST® and wrap it over the rusty surface (collecting any
percolation liquid in order to avoid any release to the environment). Cover it properly with a plastic
sheet to avoid the evaporation lose of EVAPO-RUST®. Remove everything after the rust
is removed. Duration will depend upon the
severity of rust: for flash rust removal it takes about 30 minutes for flash
rust, up to 24/48 hours for removal of medium to sever rust. Periodically check the object
during the derusting process to know the status. If desired result is not achieved
in one time, repeat one or more times. AFTER
TREATMENT:
the same as the previous method. ALWAYS PRE-TEST RIGHT OF WITHDRAWAL:
The Consumer (Consumer means any natural person who, in distance contracts, is
acting for purposes which are outside his trade, business or profession) shall
have a period of 10 (ten) working days in which to exercise of his right of
withdrawal, without penalty and without giving any reason. The only charge that must be paid by the
Consumer is the cost of returning the Products. The period for
exercise of this right shall begin from the day of receipt by the
Consumer. The withdrawal right must be
exercised by the Consumer sending a registered letter with return receipt
addressed to the following address: ENVIREM S.R.L. - Via Meucci, 11 – 40138
Bologna (BO) – Italy. ENVIREM S.R.L. shall be obliged to reimburse
the sums paid by the consumer free of charge.
Such refound shall be carried out as soon as possible and, in any case,
within 30 days. The Consumer may exercise
the right of withdrawal ONLY for undamaged parcel(s)/packet(s) and for unopen,
integral, undeteriorated and undamaged Products. DELIVERY TERMS & CONDITIONS Cost & Freight &
Insurance destination (CIF): when you buy with the terms "Cost & Freight &
Insurance destination", you pay both the product, and the transport
charges, which include the transport insurance all inclusive. You may
choose n° 2 different delivery options: 1. delivery without appointment: our freight dealer performes n° 2 following delivery attempts within
0830/1930 (every working day (Saturday & Holidays excluded) and at low
ground): the first one on the working day we will preliminary communicate you;
the second one on the following working day; if both go wrong, the ordered
product get in stock and you will have to take care for product delivery by our
freight dealer’s nearest location by paying cash in advance directly to our
freight dealer an extra cost of EUR 5,00+V.A.T. as stock clearance fees. If you
miss to performe the product delivery within the following 7 working days, the
ordered product gets back to ENVIREM S.R.L. in Italy; thereafter, in order to
get possess of the purchased product, you will have to pay us in advance an
extra cost of: EUR 5,00+V.A.T. (stock clearance fees) + 2 times the freight
charges from/to Italy; anyway, we will send you the spedition tracking code to
provide you with an easy way to track your shipments by simply adding a
tracking link; or 2. delivery on appointment: with an extra cost of EUR 3,66
our freight dealer will contact you by
phone in order to pre-agree on the product delivery’s hours and date. PAYMENT TERMS & CONDITIONS You may choose your more convenient payment
method: a. PayPal; or b. bank wire
transfer (our Swift & Iban codes will
be transmitted by email). COMMERCIAL INVOICE eBayers who purchase as Consumers (Consumer means any natural person who, in on line
contracts, is acting for purposes which are outside his trade, business or
profession),
must transmit us the whole following data: 1. the commercial invoice recipient, which is the eBayers' name
and last name 2. the commercial invoice address, which is the
eBayers' registered place of residence 3. the geographical shipping address (if different from
the eBayers's registered place of residence) 4. the eBayers' phone number for delivery eBayers who purchase as Professional Consumers (Professional Consumer means any natural or legal
person who, in on line contracts, is acting for purposes concerning his trade,
business or profession), must transmit us the whole following data: 1. the commercial invoice recipient, which is the eBayers’ business
registered name 2. the commercial invoice address, which is the
eBayers’ registered office address 3. the geographical shipping address (if different from
the eBayers’ registered office address) 4. both the eBayers’ V.A.T. code |