eBay

IMPROVED AND ENHANCED HIGH QUALITY LONGER LASTING AND BETTER PERFORMANCE

THE BEST QUALITY AVAILABLE WITH EXTRA RELIABILITY

Do not be fooled by cheaper carbons found elsewhere here on Ebay!

Pair of replacement carbon brushes to fit most vehicle heater blower motors.

TO FIT HEATER , PUMP AND BLOWER MOTOR FOR THE VEHICLES AND MOTORS LISTED BELOW:-

(This is not a comprehensive list - these high quality brushes work on a lot of 12 or 24 volt cars and as long as the measurements of the brushes shown below fit your motor it should work nicely! - Feel free to email us with any queries you may have and we will be happy to help)

 

FOR ALFA ROMEO / SELESPEED PLEASE CHECK THAT ITS 9MM X 8MM X 22MM

(some require slightly smaller brushes so you may need to file these  )

 These fit MOST models, but other models may require slight filing and they will still work

  • VW :- Passat – VW Lt35, Passat 2000

  • Caddy Van

  • Audi :- A4, Audi 80, Avant

  • BMW - Most makes

  • Mercedes :- Sprinter ,208, 308, 1998 - sprinter 310

  • Vito cdo. 108d vans. Vito, Van, 108cdi

  • 03 Sprinter 208 (may require slight filing )

  • C 180, C200 / C230 / C240 / C250 td/ CLK (W208) /C250TD, 98 (W202). C CLASS

  • Golf GTI :- MK3

  • SAAB

  • Valeo 95's ,

  • Seat Toledo

  • Citroens :-Xantia 1.9 Turbo

  • Peugeot 406

  • Renaults.:- Kangoo ,Xsara

  • Fiat Scudo (note if you have a 2003 Scudo you may need to grind brushes slightly or cut the spring slightly to fit this)

  • Doblo Cargo

  • VITO

  • V220

  • Siemens Heater Motor

  • Valeo 12v n32

  • MANY MORE!

You get TWO carbon brushes, a pair , brand new of extremely high quality and performance!

These measure 9mm x 8mm x 22mm (The length of 22mm can be shortened easily if required by grinding off)

NOW WITH EXTRA LONG COPPER WIRES EMBEDDED INSIDE - 40MM

MOST OTHER SELLERS HAVE VERY SHORT COPPER WIRES AND YOU WILL HAVE DIFFICULTY FITTING , OURS ARE EXTRA LONG TO MAKE FITTING MUCH EASIER!!!

WHY WASTE MONEY ON A NEW MOTOR COSTING 300 POUNDS WHEN IT IS SO EASY TO REPLACE THE CARBON BRUSHES?

Signs and symptoms of Carbon brushes which are worn are:-

- The fan stops and starts , sometimes if the car jolts you will get the motor stopping or starting

- Fan does not work completely

- Fan is erratic and slows /starts/ stops by itself

To change the carbon brushes is easy ! On average it only takes 30 minutes to an hour

You need to locate your heater fan blower motor which in some cars is on the passenger side - inside the car , on the underside of the front panel facing the passenger seat - remove the flap which will be held by screws and you will locate the heater/blower/fan air motor. Search the net for diagrams for your particular model but generally these are easy to remove . Once you have the heater motor out you will see there will be two clips on the side and once you remove the clips (be careful not to loose any bits) Remove the old carbon brushes and put the new ones in and connect the copper wires in. Thats it you should have a good working fan motor/blower/heater motor as good as new!

Lots of free advise and diagrams on the internet as to how to change your brushes for your model but do contact us as we have a hugh list of sites who host free diagrams and instructions on how to change these!


IF THIS DOES NOT FIT FOR ANY REASON WE WILL ACCEPT IT BACK FOR A FULL REFUND NO QUESTIONS ASKED!



PLEASE CHECK THE SIZE OF YOUR OLD BRUSHES AND EMAIL US IF YOU ARE NOT SURE

These are  Blower Motor Brushes Siz 8mm x 9 mm our product ref  B1

 If you are looking for smaller brushes 5mm x 5mm x 12mm ask for our product ref  B15

We also have a third type ref B14  size 6.3 x 8mm x 18mm

All same price, all suitable for vehicles and all can be slightly adjusted

INTERNATIONAL ORDERS WELCOME!

WE HAVE SOLD HUNDREDS OF THESE TO HUNDREDS OF HAPPY PEOPLE SO PLEASE BUY WITH CONFIDENCE!

GOOD QUALITY PERFORMANCE PRODUCT - IMMEDIATE DESPATCH !


Please ensure that the Commutator is clean & not abrasive. Always wear protective eyewear & gloves. Keep children away. Original Brand names/makes/model numbers are given for comparative purposes only & the rights of all registered trade marks are recognised and respected. These are non-oem High Quality consumable replacement parts which can fit many tools & equipments. No liability is accepted for any damage or injury. We offer goodwill 30 days Return for full refund or free exchange. Thank you





inkFrog Analytics

Get Adobe Flash player
AND NOW THE LEGAL STUFF – We are not agents of the Manufacturers and respect and recognise their name and trade mark and ownership of title for their products. These are generic high quality replacement consumable parts which fit many tools in these size brushes and we  clearly state that these are not OEM and we are not directly or by implication dealers or agents for these respected brands.