eBay

Store category

You may also like

Product Description

Packing list:
 
1 PCS EPM240 core board
1 PCS USB power wire .
1 PCS Altera USB Blaster ( with USB wire and  10 pin JTAG wire );
1 PCS USB TO TTL232;
1 PCS 4 pin Female to Female dupont wire ;
 

 

 
EPM240 Core board : 
 
Diagram : Please contact me on ebay message for diagram after your order !
 
Onboard EPM240T100C5N chip
 
50Mhz Active crystal
 
All pins from CPLD are Labelled and available onboard
 
Altera Official standards JTAG Interface
 
Two 5V 3.3V output to provide power for the peripheral
 
Two independent LED lights for test core board  
 
A Independent button for test core board
 
Size : 9cm X 6cm (9:6 is Golden ratio ^_^) 

    
 
 
 
PCB Board 3D View :  
 
 
 
 
Description :
 
Name CPLD EPM240T100C5N Mini Development Board
CPLD
EPM240T100C5N
Input Voltage DC 5V
JTAG Port Available; 5x2 pins; Compatiable with Byte-Blaster / USB-Blaster
IO pins All pins from CPLD are Labelled and available onboard
Crystal 20 MHz
 
 
Diagram : Please contact me on ebay message for diagram after your order !
 
Altera USB Blaster; 

 
Accessories :
 
Description :
 
Feature :
1.Stably support SignalTap II embedded logic analyzer function ,no mistake while crawlling data;
2. Fully support all Altera products such as :
   CPLD: MAX3000, MAX7000, MAX9000 and MAXII
   FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc.
   Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
   Enhanced configuration devices: EPC1, EPC4.
3. Supports 3 download mode: AS, PS and JTAG;
4. Support and Nios II embedded soft core processor communication and debugging, Rev.C latest version Hardware. Support jtag_uart;
5. Speed​​: 6 times faster than parallel port download cable ByteBlasterII;
6. Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
7. Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
8: Voltage : 1.5~5V JTAG IO Voltage . 
 
System configuration:
1, Windows XP, Windows Vista, Windows7 , USB interface;
2, Quartus II version 4.0 or newer version; 
 

This programmer uses standard 10-Pin ICD10 interface, the Pin assignment is shown as followed:
10-Pin interface (the triangle mark on cable "▼" means 1st pin):

2

4

6

8

10

1

3

5

7

9 

 
 
1 pcs USB to TTL 



Description:
PL2303 Replace FT232 USB to RS232(TTL Level) for Arduino Pro Mini Download
Support USB 1.0 and USB 2.0
500mA self recovery fuse for protection
Adopt imported controller PL2303HX,which can stabilize the flash with high speed

USB to TTL serial port, 6 pin assignment as below:

3V3 GND +5V TXD RXD DTR

Compatible with PRO MINI download port


Supports the following Windows OSes:

Windows 98SE
Windows ME
Windows 2000 SP4
Windows XP SP2 and above (32 & 64 bit)
Windows Server 2003 (32 & 64 bit)
Windows Server 2008 / 2008 R2 (32 & 64 bit)
Windows Vista (32 & 64 bit)
Windows 7 (32 & 64 bit)

 
 

We accept credit card payments and echecks through PayPal. A non-payment dispute will be opened if full payment is not received after 14 days of auction.

PushAuction