1 X 500WATT CLASS D AUDIO AMPLIFIER BOARD - IRS2092
（AA-AB31512）
Picture Showcase

Description

This mono high power audio amplifier board employs IR's High Voltage, high performance class D audio amplifier driver IRS2092SPBF and 200V Single N-Channel HEXFET Power MOSFET IRFB4227 and is capable of delivering 500W output power into a 4Ohm load. Based on Class D topology and the IRS2092 IC, this audio amplifier board features high efficiency as 95% and high audio performance with low distortion and low noise level. Easy installation, high power output and high reliability make this audio amplifier board suitable for subwoofer, home audio, DIY audio, loudspeakers, car audio and demanding industrial applications such as Physical Therapy Machines, Underwater Acoustics. Dual power supply is required for this amplifier board ang the suggested power supply range is ±55V - ±65V.

High Quality Audio Performance

Thanks to dedicated PCB layout design, careful components selection and engineers’ attentive debugging, this high power audio amplifier board features high audio performance, whose SNR reaches up to 98dB and THD+N performs well as 0.03% @ 4Ohm, 1W, 1kHz. Therefore, this module can provide quite powerful, warm and clean sound.

Flexible Load Characteristics and Wide Load Range

This audio amplifier module features flexible load characteristics with optimization in the frequency response. It has been tested in the lab with inductive load like a coil, capacitive load and resistive loads to make sure its stability and performance. Due to its low output impedance, this audio amplifier board supports wide load range, which can work stably even with a 1Ohm load without impact by the loudspeakers load characteristics.

Disclaimer: Extra attention needs to be paid for any operation with purely inductive and capacitive loads. It is suggested to send an inquiry email to us to confirm system compatibility with us before you use it to drive such loads.

Wide Bandwidth form 10Hz-22kHz

IRS2092 series can handle with wide bandwidth from 10Hz to 22kHz with uncompromising frequency response and audio performance, not only meeting requirements of audio system but also satisfying special demands of some applications such as Physical Therapy Machines, Underwater Acoustics and so on. With ten years’ experience and expertise, Sure Electronics is committed to providing best possible solutions for audio hobbyist or industrial customers. For any non-audio applications, customers are suggested to send an inquiry e-mail to Sure Electronics for system compatibility confirmation.

Dual Power Supply

This IRS2092 audio amplifier board requires dual power supply, in which case, power supply dedicates its full output voltage to single rail, ensuring the output power of amplifier. Taking full account of the power solution and saving customers’ material cost, Sure Electronics provides matched power supply solution as using rectifier and transformer. With the input of Dual 115V, which could be paralleled as 110/115V or serialized as 230/240V input, the transformer can provide Dual 48V, each 1000VA, and dual 15V auxiliary output with 1.25A maximum load in each coil to the rectifier who can convert AC input voltage into separate positive DC and negative DC voltage outputs. This combination can provide maximum voltage as ±67V, meeting most requirements for Audio Applications.

High Reliability and Long Service Time

A robust heatsink along with a low noise, cooling fan is installed on the board for sufficient heat dissipation to avoid damage caused by overheat. Full protection circuit, like over temperature protection, overcurrent protection and DC offset protection, is equipped on this board for high reliability and long service time.

Disclaimer

Please note that this audio amplifier is designed for audio applications. Please do not use it in non-audio applications. If you want amplifiers for non-audio applications, please contact with us. We will provide you with full set of audio solution with special optimization in specific requirements on frequency, protection or output voltage of different applications.

Package Includes

1pc AA-AB3512

Basic Information

  • StyleBoards
  • Number Of Channel(s)1
  • Output Power500
  • Size6 x 4.5 inches (152.4mm x 114.3mm)
  • ChipsetIRS2092
  • Heat DissipationHeat Sink & FAN
  • Supported Parallel Bridge Tied Load Mode/
  • inputSingle ended Line-in,
  • Power Voltage55V-65V

Features

  • Output Power
  • 500W@ 4Ohm ±60V DC THD+N 10%
  • 405W@ 4Ohm ±60V DC THD+N 1%
  • Power and Shutdown Indicator
  • 1Ohm Stable Design
  • Wide Bandwidth from 10Hz to 22kHz
  • Full Protection
  • DC Offset Protection
  • Low Noise Cooling Fan
  • Optimized Heatsink Design
  • 4-screw Easy Installation
  • Weight:580g/1.28 lbs (±10%)
  • Size:6.00inchX4.50inchX2.90inch

Specification

Specifications typical +25℃, Powered by +-60V DC, unless otherwise noted. Specifications subject to change without notice.
ParameterConditionsMin.Typ. Max.Units
Power Supply-+-55+-60+-65VDC
Idle PowerSD Floating, FAN ON-4.57W
SD Floating, FAN OFF-35W
Standby PowerSD Connected to GND, FAN OFF-0.63W
Maximum Current 500W   4 Ohm -9.1 -A
Efficiency500W   4 Ohm 88-93%
Minimum Load Impedance--3-Ω
Switching FrequencySD Floating- 396-KHz
Under Voltage Production--+-50-V
Over Voltage Production--+-72-V
Over Temperature Production--100-℃
Fan Active  Temperature--55-℃



Performance


per-3.jpg

per-1.jpg









per-2.jpg



Shipping & Handling

We process your order within 2 business day upon payment(note: NOT counting holidays or weekends).
International shipping also available, please note by default all international packages does not come with tracking unless upgraded to priority mail.
Package transit time: please expect 20-25 business days by Economy shipping,10-15 business days by Standard Shipping, 3-7 business days by Express shipping.

Payment Method

Payment:
Payoneer Preferred.
Local pickup NOT available at this time.

Refund and Return

Please read the item description and check the pictures carefully before bidding. Return or refund is available only if item DOA or there's error in item description causing the item not fitting your need. In such cases, seller pays for all related shipping cost if any.
Returns are also acceptable if buyer purchased this by mistake and item still in good condition for reselling. Buyer is responsible for all related shipping cost.
FeedbackWe maintain high standards of excellenceandstrive for 100% customer satisfaction!Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.