Se acquisti più pezzi di questo articolo, potresti risparmiare sulla spedizione!

Riempi il carrello e clicca sul pulsante 'RICHIEDI IL TOTALE AL VENDITORE' o contattaci per offerta personalizzata!


!!! NUOVO CON CHIP SIM800F !!! (sostituisce chip SIM900)

GSM/GPRS SHIELD SIM800F compatibile Arduino 

con SIM800F SIMCOM Quad-Band 850 / 900/ 1800 / 1900 MHz

COMPATIBILE CON SCHEDE ARDUINO UNO / 2009 / MEGA / MEGA 2560 ** ecc.

Gestisce SMS / AUDIO in-out / Servizi GPRS.

Antenna inclusa. Lo Slot lettore SIM ( standard) è sotto la scheda.

Usa librerie standard per "SIM900" GSMLIB / GSMSHIELD

NOTA BENE : Funziona sulla rete GSM (2G) - NON sul reti solamente 3G o 4G -Utilizzare una SIM adatta !

NOTE: Supports GSM Net 2G - ( NOT 3G / 4G net only )


( Esempio Link alle librerie per lo schield : SIM900 LIBRARY )

Collegata ad una scheda Arduino può inviare / ricevere SMS ( per gestire un controllo remoto),

inviare / ricevere chiamate ( con audio) ,

utilizzare il protocollo TCP/IP per comunicare via internet come CLIENT o SERVER , inviare MAIL ecc.

( ** Istruzioni per l'utilizzo con schede MEGA / Mega2560 :

HTTP://digilander.libero.it/olmste/ARDUINO%20SHIELDS/gsm2560.zip )

Caratteristice principali:

* Quad-Band 850 / 900/ 1800 / 1900 MHz

* 3 LED indicatori: GSM Shield power, SIM800F power and net status, GSM Shield power

* 3 Pulsanti: SIM9800F Power Button ( premendolo 1 sec è possibile togliere tensione al modulo GSM, RESET ( = resetta Arduino), SIM800F Reset Button ( resetta solo il modulo GSM).

* Lo shield prende l'alimentazione dalla scheda Arduino la quale va alimentata con alimentatore esterno da 9V e 2A di corrente di picco ( può non funzionare quando collegata ad una presa USB standard ) .


* Pins ARDUINO USATI / Used Pins:

RX ( D0) , TX( D1) se si utilizza la HW serial port;

D2 ( RX sw) , D3 (TX sw ) se si utilizza la sw serial;

D7 : Ring Indicator ( indica ricez. chiamata o SMS)

D8 (OUT) : SIM900 power ON /OFF command.

D9( OUT) : SIM900 RESET


Documentazione:

* produttore: https://www.tinyosshop.com/sim800f-arduino-shield

_____________________________________________________________________________________________

Mais specs:

Usea SIM800F SIMCOM Quad-Band 850 / 900/ 1800 / 1900 MHz

COMPATIBILE with ARDUINO UNO / 2009 / MEGA / MEGA 2560 **

Handles SMS / AUDIO in-out / GPRS services

Included Antenna.

Uses standard library for "SIM900" GSMLIB / GSMSHIELD

( NOTE : works on GSM (=2G) - not on 3G or 4G )

( Library Link : SIM900 LIBRARY )

( ** Instruction for use with MEGA / Mega2560 :

HTTP://digilander.libero.it/olmste/ARDUINO%20SHIELDS/gsm2560.zip )

The GPRS/GSM Shield provides you a way to use the GSM cell phone network to receive data from a remote location. The shield allows you to achieve this via any of the three methods:

  • Short Message Service
  • Audio
  • GPRS Service

The GPRS/GSM Shield provides you a way to use the GSM cell phone network to receive data from a remote location.

The shield allows you to achieve this via any of the three methods: Short Message Service Audio GPRS Service The GPRS Shield is compatible with all boards which have the same form factor (and pinout) as a standard Arduino Board.

The GPRS Shield is configured and controlled via its UART using simple AT commands. Based on the SIM900 module from SIMCOM, the GPRS Shield is like a cell phone.

Features Based on SIMCom's SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control via AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal). Embedded TCP/UDP stack - allows you to upload data to a web server. Speaker and Headphone jacks - so that you can send DTMF signals or play recording like an answering machine.

SIM Card holder and GSM Antenna - present onboard.

Low power consumption - 1.5mA(sleep mode) Industrial Temperature Range - -40°C to +85 °C Please email us to get the documents.

Note:

  • Because SIM800F peak current more than 2A. This shield must work with a external DC9V power supply on Arduino board. ( not USB supply)
  • If you are using MEGA2560. Just need to connect the middle pins of RX and TX jumpers to RX1 TX1 on Arduino Mega 2560. And change the code setting.

Features

  • Based on SIMCom's SIM800F Module
  • Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world.
  • Control via AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands.
  • Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
  • Embedded TCP/UDP stack - allows you to upload data to a web server.
  • Speaker and Headphone jacks - so that you can send DTMF signals or play recording like an answering machine.
  • SIM Card holder and GSM Antenna - present onboard.
  • Low power consumption - 1.5mA(sleep mode)
  • 12 GPIOs, 2 PWMs and an ADC (all 2.8 volt logic) - to augment your Arduino.
  • Industrial Temperature Range - -40°C to +85 °C
  • Kit weight: 56g