Se acquisti più pezzi di questo articolo, risparmia sulla spedizione!
Riempi il carrello e clicca sul pulsante 'RICHIEDI IL TOTALE AL VENDITORE' o contattaci per offerta personalizzata!
MODULO L298N DUAL H BRIDGE DC STEPPER
MOTOR CONTROLLER DRIVER
Universale ( per Arduino, PIC, AVR, ARM )
Per motori stepper / DC / Bobine / Relè ecc
L298N DUAL H-BRIDGE UNIVERSAL DRIVER MODULE
CAN DRIVE ONE 2-PHASE STEPPER MOTOR, ONE 4-PHASE STEPPER MOTOR OR TWO DC MOTORS,COILS OR RELAY.
Modulo per pilotare un motore passo-passo fino a 4 fasi, oppure due motori DC o un motore passo-passo bipolare.
Richiede una doppia alimentazione:
5Vdc per la logica e una tensione compresa tra 5-35Vdc per alimentare il lato potenza del motore.
Il 5Vdc può essere dato dall'esterno tramite morsetto '5V' (rimuovere il ponticello '5V') oppure preso dalla alimentazione '12V' dei motori e regolato del 78M05 a bordo (mettere il ponticello '5V') .
Tensione di alimentazioe logica: DC5V
Range di alimentazione: 7V - 35V
Corrente di alimentazione logica: 0mA - 36mA
Corrente massima di carico: 2A
Jumper x abilitare il regolatore 78M05 a bordo per generare il 5V logica (se si usa alimentazione per i motori maggiore di 12V, togliere il ponticello '5V' e fornire alimentazione 5V logica dall'esterno)
Specifications:
- 0-3,3V and 0-5V COMPATIBLE INPUTS
- H-bridge driver (dual)
- Master chip L298N
- Logic Supply voltage 5V ( 4,5 MIN - 5,5V MAX )
- Drive voltage 7V-35V
- Logic Current 0mA-36mA
- Drive current 2A (continuous single bridge) / 3A peak max
- Maximum Power 25W (when the temperature T = 75 Deg C)
- Built-in 78M05 gives +5V regulated output supply available ( DO NOT input voltage to this supply BEFORE REMOVE JUMPER)
- Protection diodes on all outputs
- External dimensions: 43x43x27 mm
Module pinout:
12V: Connect your motor supply voltage here, maximum of 35V DC.
GND: 0V
JUMPER: 12V jumper to 78M05 - remove this if using a supply voltage greater than 12V DC. This enables power to the onboard 5V regulator
+5V: 5V output if 12V jumper in place, ideal for powering your Arduino (etc)
ENA: DC motor 1 enable jumper. Leave this in place when using a stepper motor. Connect to PWM output for DC motor speed control.
ENB: DC motor 2 enable jumper. Leave this in place when using a stepper motor. Connect to PWM output for DC motor speed control.
IN1 : MOTOR1
IN2 : MOTOR1
IN3 : MOTOR2
IN4 : MOTOR2
OUT1: DC motor 1 "+" or stepper motor A+
OUT2: DC motor 1 "-" or stepper motor A-
OUT3: DC motor 2 "+" or stepper motor B+
OUT4: DC motor 2 "-" or stepper motor B-
Product Features:
This module uses ST's L298N chip as the main driver, driving ability, low heat, strong anti-interference ability.
This module use the built-in 78M05 and take power by driving the power section( +12V) , but in order to avoid damage to the regulator chip, when use is greater than the drive voltage of 12V, use an external 5V logic supply.
The module uses a large-capacity filter capacitors, drain diode can improve reliability.
Power led indicator on 5V.
Peso confezione: 25gr