Se acquisti più pezzi di questo articolo, risparmia sulla spedizione!

Riempi il carrello e clicca sul pulsante 'RICHIEDI IL TOTALE AL VENDITORE' o contattaci per offerta personalizzata!



MODULO L298N DUAL H BRIDGE DC STEPPER


MOTOR CONTROLLER DRIVER


Universale ( per ARDUINO / PIC ecc. )


Modulo per pilotare un motore stepper a 4 FASI , 2 motore stepper a 2 FASI,

oppure due motori in continua ( DC ) , o relè , bobine...

Con jumpers per la gestione dei pull-up degli ingressi di controllo e del current sense.


L298N DUAL H-BRIDGE UNIVERSAL DRIVER MODULE
CAN DRIVE ONE 2-PHASE STEPPER MOTOR, ONE 4-PHASE STEPPER MOTOR OR TWO DC MOTORS,COILS OR RELAY.


Modulo per pilotare un motore passo-passo fino a 4 fasi, oppure due motori DC o un motore passo-passo bipolare.
Richiede una doppia alimentazione:
5Vdc per la logica e una tensione compresa tra 5-35Vdc per alimentare il lato potenza del motore.
Il 5Vdc può essere dato dall'esterno tramite morsetto '5V' (rimuovere il ponticello '5V-EN') oppure preso dalla alimentazione 'VMS' dei motori e regolato del 78M05 a bordo (mettere il ponticello '5V-EN') .
  • Corrente in uscita è di 2A max su ogni canale
  • Potenza massima: 25W
  • Doppio ponte a H
  • Chip L298N (ST)
  • Tensione di alimentazioe logica: DC5V
  • Range di alimentazione lato potenza 'VMS': 5V-35V (7-35V se necessario usare il regolatore 5V a bordo)
  • Corrente di alimentazione logica: 0mA - 36mA
  • Led spia presenza 5V
  • Jumper x abilitare il regolatore 78M05 a bordo per generare il 5V logica
  • 4x Leds per livello fasi 1-4
  • 6x Jumper x contyrollo dei pull-up ingressi sense
  • Dimensioni: 60mm*55mm*30mm
(A seconda dei lotti la scheda può variare leggermente rispetto all'immagine o presentare piccole variazioni nel montaggio dei componenti o colore del circuito stampato ma non varia nelle dimensioni o caratteristiche tecniche)

The L298N driver module, using ST's L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential.

Features:

Driver: L298N Dual H Bridge DC Motor Driver IC

Driven part of the terminal supply area Vs: +5 V ~ +35 V; such as the need to take power within the board, the supply area Vs: +7 V ~ +35 V

Driven part of the peak current Io: 2A

The logical part of the terminal supply area Vss: +5 V ~ +7 V (can take power within the board +5 V)

The logical part of the operating current range: 0 ~ 36mA

Control signal input voltage range:

Low:-0.3V

High: 2.3V


Enable signal input voltage range:

Low: -0.3

High: 2.3V

Maximum power consumption: 20W (when the temperature T = 75 Deg C)

Storage temperature: -25 Deg C ~ +130 Deg C

Other Extensions: control of direction indicators, the logic part of the plate to take power interface.

Driver Board Size: 55 x 60 x 30 mm

Drive plate Weight: 28g
Other functions: control the direction indicator, power indicator, current detection, the logic part of the board to take power interface.

Peso confezione: 29gr