MODULO W1209 - Mini TERMOSTATO DIGITALE
CONTROLLO TEMPERATURA da -50°C a 110°C
con SONDA IMPERMEABILE
Alimentazione: 12V oppure 5V (selezionare la versione preferita)
(Gli schemi per semplicità riportano solo la versione a 12V )
DIGITAL THERMOSTAT CONTROLLER / 12Vdc or 5Vdc supply
Di facile programmazione
Funzioni programmabili:
Soglie Temperatura Attacco/Stacco (ISTERESI)
Condizionamento /Riscaldamento
Limiti MIN/MAX di funzionamento
Ritardo attivazione Relè
Correzione lettura temperatura
(Tutte le impostazioni rimangono in memoria anche a termostato spento)
- Tipo di prodotto: termostato digitale con display 3 digit a LED ROSSI ( risoluzione 0.1°C)
- Ingressi di misura: NTC (10 K 0.5%) sensore Impermeabile (cavo lungo circa 28cm per versione 5V e 49cm per versione 12V)
- Gamma di controllo/ programmazione : -da 50°C a +110°C
- Modello: W1209
- Uscita: 1 relè 10A / 125Vac - 10A / 14Vdc ( Contatto pulito N.O)
- Led che segnala lo stato ACCESO del relè
- Isteresi di precisione da 0.1° a 30.0°
- Alimentazione: 12Vdc o 5Vdc
- Consumi: 5V=14mA/90mA ; 12V= 18mA/70mA
- Tipo di Display: 0.28 " 3 digit
- Allarme di alta temperatura: 0-110 °
- Consumo di energia: < = 35MA in standby, <= 65MA con relè acceso
- Frequenza di aggiornamento del display: 0.5 secondi
>> Per carichi importanti sulla rete 220Vac consigliamo di aggiungere il Modulo RELE' 12V(o 5V) / 250Vac-10A ausiliario in quanto il relè a bordo (più piccolo) permette uso di carichi moderati, specialmente se induttivi <<
>> BOX ACRILICO (da montare) : OPZIONALE <<
ISTRUZIONI complete IN ITALIANO! Richiedile inviandoci un messaggio!
Dimensioni Modulo Termostato: 40*50mm H 15mm
ENGLISH:
W1209 Digital Thermostat Temperature Display & Switch Module + Sensor
Temperature range: –50~110°C
Dimensions: 40*50mm H15mm
Temperature control mode: ON / OFF
Resolution: When temperature is 0.1°C, the resolution is –9.9~99.9, other temperature segment is 1°C
Control accuracy: 0.1°C
Hysteresis accuracy: 0.1°C
Refresh rate: 0.5S
High temperature protection: 0–110°C
Supply voltage: DC 12V or 5V
Static current: <= 35MA, attract current <= 65MA
Output power: 20A relay open contact
Measurement input: NTC (10K 0.5%) Waterproof Sensor.
Environmental requirements: –10°C~60°C, Humidity 20% –85%
How to operate:
Connect the power supply and equipment, the controller can be powered to measure the temperature is displayed, press the SET button, the display temperature flashes, press + – to set the desired temperature (hold down the + – quick lift) set When finished, press SET to confirm and return, then the controller automatically execute by setting the relay off. The thermostat is 10A relay outputs to meet a variety of high–power loads.
The lights, LED and buzzer status description
LED: extinguish to indicate relay off, light indicate the relay is closed
Digital Tube: Showing LL means sensor opens; display HH indicates beyond the measurement range thermostat will forcibly disconnect relay; high–temperature alarm display —
Code Indicating Set range Inital Setting
P0 Mode set(Heating or Cooling) C/H C
P1 Set return difference 0.1–15 2
P2 Up limit 110 110
P3 Down limit –50 –50
P4 Temp. Adjust –0.7–7°C 0
P5 Delay start time 0–10 minutes 0
P6 High temp.alarm 0–110°C off
At “OFF” state, Long press + –,start and then recovery to inital set