Power Over Ethernet Kit for 4x Raspberry Pi
(250M 4ports PoE Switch+ Micro USB PoE Splitter)
for Raspberry Pi B/B+/2/3
Support EXTEND mode, max Network Cable length to 250 meters
NOTE. When EXTEND mode enable, the Max bandwidth for the Power Link (PoE) port 1-4 network port will be reduced to 10Mbps for each one.
(The up-link is not affected, it will always working at 100Mbps max speed)
PoE Switch Specification:
| ALL Port: | Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。 | |||||
| Power Link Port 1-4: | any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs) | |||||
| Power LED | LED ON: power on. LED OUT: power off | |||||
| Green Light LINK/ACT | LED ON Indicates the port is connected to a network device and has been started | |||||
| LED OFF Indicates that this port is not connected to a network device or has not been started | ||||||
Standard | IEEE 802.3 10BASE-T Ethernet |
IEEE 802.3u 100BASE-TX Fast Ethernet | |
IEEE 802.3x Full-Duplex flow control | |
Protocol | CSMA/CD Ethernet |
Data Transfer Rate | Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex) |
Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) | |
IC Chips | IC Plus IP178G |
Network Media(Cable) | 10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m) |
100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) | |
PoE Power on RJ45 | Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8 |
DC Output: 52V, Per port Max 1A or 50Watt, 4 POE ports Total Max. 75Watt | |
Number of Ports | 5 x 10/100Mbps Auto-Negotiation RJ45 ports with 4 PoE enabled (port-1 ~ port-4) |
Power Input | AC Input: 110V ~ 240VAC, 50Hz ~ 60Hz. |
DC OutPut: 52V/1.85A | |
Power Consumption | 3.2 Watts (max. no PD connected) |
According to the actual power consumption of equipment | |
Temperature | Operation Temperature:0 ~40℃ (32 ~104℉) |
Storage Temperature: -40 ~70℃(-40 ~158℉) | |
Humidity | Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing |
Product Dimensions | 132mm W x 66mm D x 32mm H |
RAM Register Capacity | 64K bytes per device |
MAC Address List | 1K entries per device |
Frame Forward Rate | 10Mbps Ethernet: 14880pps/Port 100Mbps Ethernet: 14880pps/Port |
PoE Splitter Specification:
Compliant with IEEE802.3af
Isolation: 2.5kV
Power Input: DC44~57V
Power Output: DC5V 2.4A
Data&Power INPUT Port: from RJ45 female (Compliant with IEEE802.3af/at PoE)
Data Output Port: RJ45 Male
Power Output Port: Micro USB Power Plug
Data Transfer Rate: 10/100Mbps
Devices will be detected before poe input
Power Pin:support both 1/2(+/-),3/6(-/+) or 4/5(+),7/8(-)
Body size: 80 x 27x 22 mm
DC cable length：165mm
RJ45 Modular Plug cable length：155mm
Weight : 55g
Item Included:
Output 5V 2.4A Active PoE Splitter(Micro USB Power Plug) x4
75Watt 5pots 4PoE Passive PoE switch(DSLRKIT MID4P1U-E250) x1
AC power plug is UK or EU type,if you need other type (AU or US),Please leave a message.
