4 Axis for medium size Router Mill Plasma or Laser

 

1.  5 axis breakout board

• 

• Description:

  • It can most connection 5pcs driver and control 5pcs motor in the same time
  • It is with 4-wire limit switch to insure our safty movement
  • It is with relay port to contro the cnc spindle
  • Working voltage is 5VDC and support with MACH3,EMC2,KCAM4 software
  • Size:9x5.7cm

   

   

   

  25-pin parallel port control is defined as follows:  

  DB25 control pin (PIN)	The pin of the drive board	Comment
  1	STEPB	B(Fifth axis)pulse signal
  2	STEPX	X(First axis) pulse signal
  3	DIRX	X(First axis) direction of the signal
  4	STEPY	Y(Secondaxis)pulse signal
  5	DIRY	Y(Second axis)direction of the signal
  6	STEPZ	Z(Third axis) pulse signal
  7	DIRZ	Z(Third axis) direction of the signal
  8	STEPA	A(Fourth axis) pulse signal
  9	DIRA	A(Fourth axis) direction of the signal
  10	LIMIT-1	Limit input interface 1
  11	LIMIT-2	Limit input interface 2
  12	LIMIT-3	Limit input interface 3
  13	LIMIT-4	Limit input interface 4
  14	DIRB	B(Fifth axis) direction of the signal
  15	Vacant
  16	RLY	Relay control
  17	EN	All axis enable
  18-25	GND	GND

  Remark:this 5 axis breakout board can connction with many driver type as a CNC 3/4/5 axis driver controller kit,pls if you intresting pls contact us!

  

• 
  

 

 

 

2.  CW5045 high microstep stepper motor driver

Description:

• Input voltage: 24-50VDC
• Output current: 1.3,1.8,2.3,2.7,3.2,3.7,4.2,4.5A
• Mircostepping: 1(1.8°),1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256;     
•                      1/5,1/10,1/25,1/50,1/125,1/250

• Protect form: Overheated  protect, lock automatic half current ,error connect protect
• Working environment: Temperature-15-40deg Humidity<90%
• It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A, 

 

 

• 

Switch Choice: (ON=0,OFF=1) 

1.Microstepping choice:

SW5	0	0	0	0	0	0	0	0	1	1	1	1	1	1
SW6	0	1	0	1	0	1	0	1	0	1	0	1	0	1
SW7	0	0	1	1	0	0	1	1	0	0	1	1	0	0
SW8	0	0	0	0	1	1	1	1	0	0	0	0	1	1
Micro	1/2	1/4	1/8	1/16	1/32	1/64	1/128	1/256	1/5	1/10	1/25	1/50	1/125	1/250

 

2.Current choice: 

SW1	0	1	0	1	0	1	0	1
SW2	0	0	1	1	0	0	1	1
SW3	0	0	0	0	1	1	1	1
Current(A)	1.3	1.8	2.3	2.7	3.2	3.7	4.2	4.5

 

3.Full current or half current choice: SW4:0=Full current; 1=half current

We also can offer customer NEMA17-23 stepper motors,so if you need pls contact us.

 

Application Notice:

1. To avoid use in the oil contamination,dust and corrosive gas environment
2. To lay it in a place with good ventilation
3. Pls note the connection with right power(+ and -) to avoid broken the driver
4. Pls test it when confirm the connection is right.

2. Stepper Motor

General Specification:

Step angle accuracy:+ -  5%(full step,not load)

Resistance accuracy: + - 10%

Inductance accuracy:+ - 20%

Temperature rise: 80deg Max(rated current,2 phase on)

Ambient temperature ----------—20deg  ----  +50deg

Insulation resistance:100ohm  Min,500VDC

Insultion Strength--------500VAC for one minute

Datasheet(23HS2430,Front shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length,425 oz-in or 28kg.cm holding torque)

 

 

 

 Note:if you need single shaft pls contact us,we have in stock.

 

  

Motor lead wires:

Red:       A+

Green:   A-

Yellow:   B+

Blue:      B-

 

3.Switching power supply

400W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:36v/9.7 A,single output switching power supply

Shipping

Please open the package and check if there are some damages before sign, if there are some damages,please do not sign and contact us immediately.

Payment

Payment must be made within 48 hours of the auction end time.

We accept PAYPAL Payment.

Problem & Feedback

Please give us the opportunityto resolve any problem when you have,we concern your problem and we will try our best to resolve it.

Pls email us before you want to leave any negative feedback.

Refund

Any reason required for all refund.Item must be in it's original condition and no physical damage.

When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos.