4 Axis CNC Router Kit Nema 23 Stepper Motor 270Oz-in &4P MD430 Driver &Power Supply for CNC Router Engraving Milling Machine
Good News:
Welcome European customers to our shop,we have this product in our Germany Warehouse,so we will ship this product from Germany to you directly |
| |||||||||||||||||||||||||||||||||||||
Package included:
- 4 x 23HS8430B Dual Shaft Nema23 Stepper Motor (3A,76mm,1.8deg,180N.cm)
- 4 x TB6560 MD430 single axis driver
- 1 x 350W 24V 10A DC switching power supply
- 1 x 5 Axis breakout board
- 1 x DB25 parallel cable
- 1 x USB cable
- English user manual for breakout board and stepper motor driver will send by email.
100% Brand New and High Quality!!!
1. TB6560 MD430 Low noise of stepper motor driver
1. IntroductionMD430 is a compact single axis bipolar3.0A/phase stepper motor microstepping driver with step and directioninputs, DIP switch settable step mode (full, half, eight andsixteenth--S3/S4), torque (100%, 75%, 50%, 20%--S5/S6) ,work current(0-3A--SW1/SW2/SW3) and decay mode (0%, 25%, 50% and 100%). MD430-HZ
2. Features1) Single-chip motor driver for sinusoidal microstep control of stepping motors2) Power on in indication led3) 3Amps-34Volts(Supply voltages:12-34DC)4) Full step, half step, eight step and sixteenth step(selection with dipswitches)5) Torque (100%, 75%,50%, 20%)6) Work Current (0-3A selection with SW1/SW2/SW3)7) 4 Wire,6 Wire,8 Wire stepper motors can be used8) Two phases bipolar driver9) Easy wiring with standard screw terminals10) Step frequency up to 100khz11) Fuse protection on power supply rail(protects the board,but also your power supply and motor)3. Application fieldsSuitable for all kinds of small andmedium-sized automation equipment and apparatus For example, lasermachines, laser engraving &cutting machine, laser subsurfaceengraving machine, laser handicraft cutting machine, (nonmetalmaterials) laser marking machine, laser seals engraving machine andphotosensitive seal machine.2. 5 axis CNC Breakout board interface adapter board
Description:1, full support for MACH3, KCAM4, EMC2, the PC software to support parallel port control;2, leads to all the parallel port of all 12 data transmission output pin, which can control the five stepper motor driver;3, with 5-way input interface, you canaccess the limit switches and emergency stop switch, reset knife;5 input LED indicates the status of the input;4, all the way with a 12A relay control, normally open, normally closed leads, user-friendly connection;5, power supply with 5V USB power supply or external power supply to facilitate the access of external powersupply;On the external drive enable signal amplification, filtering,enhancement processing;6, the pulse, the direction of signal shaping, enhanced with a carrying capacity, data transmission speeds reach 10 MBit / S;7, the output pin with extension interfaces can 2.54mm pin 2.54mmXH-Block;Superiority:1,the use of new imported Japanese Toshiba TB6560 chip (disguising);2,The base used dense teeth radiator, cooling super, to ensure the stable operation of equipment;3,the input signal using a high-speedopto-isolation to ensure not losing steps, which the pulse directionsignals with the same level of 6N137, dual high-speed optocoupler;4 a variety of semi-flow mode and the semi-flow current selection, the use of more flexible5,Decay mode is adjustable to ensure the motor running smooth;6.,Sophisticated appearance size cooling pad size: 75mm * 65mm, four mechanical installation positioning holesize is: 67mm * 58, mounting hole diameter is 4mm7,Set method detailed table on the board, easy to use;8,With anti-reverse circuit, even if not careful the power plug back and will not burn the chip, the use of safer.3. Stepper Motor
General Specification:
Step angle accuracy:+ - 5%(full step,not load)
Resistance accuracy: + - 10%
Inductance accuracy:+ - 20%
Temperature rise: 80deg Max(rated current,2 phase on)
Ambient temperature ----------—20deg ---- +50deg
Insulation resistance:100ohm Min,500VDC
Insultion Strength--------500VAC for one minute
Datasheet (23HS8430B,front shaft is 8mm diameter shaft,21mm lenth,back shaft is 6.35mm dia and 10mm length,270oz-in or 18kg.cm holding torque)
Note:if you need double shaft pls contact us,we can produce.
Motor lead wires:
RED: A+
GREEN: A-
YELLOW: B+
BLUE: B-
4.Switching power supply
350W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:24v/10 A,single output switching power supply
Shipping
· Please open the package and check if there are some damages before sign, if there are some damages,please do not sign and contact us immediately
· We ship to worldwide but if your country’s custom is strict, please contact us before you bid to check detail and confirmed.
· Please check out your address carefully when processing order.We are not responsible for wrong or undeliverable address.
Payment
· We accept paypal payment only.
· Payment must be made within 48hours of the auction end time
Problem&Feedback
· Please give us the opportunityto resolve any problem when you have,we concern your problem and we will try our best to resolve it.
· If you are not satisfied, please contact us to resolve any issues. Please do NOT leave negative feedback without asking for help. We work hard to make sure EVERY CUSTOMER 100% satisfaction.
· For any inquiries,issues or assistanceplease contact us via eBay message
Refund
· When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos to us.
· Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us
· Please feel free for any questions, all the emails will be replied within 1-2 business days,if you didn’t receive any mail, maybe it’s in the junk mail fold.
· We are online from Monday to Saturday.