Good News:
We have USA Warehouse in United States,so we will ship from USA Warehouse to United States.
Package:
100% Brand New and High Quality!!!
1. USBCNC breakout board
1) Products brief introduction
USBCNCV4.0 is a high performance motion controller which based on PC software USBCNC control, the system can complete the conversion from G code to connect stepper motor’s driver motion control signal without requiring any additional hardware and software. This control card is compatible with most stepper driver and servo driver,it is a perfect controller that instead of parallel Mach3 interface board.
This interface board is based on USBCNC MK1 and just use in our provide software and function, cannot support other versions of the software and function
Minimum configuration:
1) CPU:1GHz
2) Memory: 512MB
3) 500MB free disk space
4) DIRECTX9 graphics device with WDDM 1.0 or higher driver
5) USB 2.0 interface
6) Net FRAMEWORK 3.5SP1
The recommended configuration:
1) CPU:2GHz dikaryon
2) Memory: 2GB;
3) 1G free disk space
4) DIRECTX9 graphics device with WDDM 1.0 or higher driver
5) USB 2.0 interface
6) Net FRAMEWORK 3.5SP1
3.Production feature
1. After the revision,V4 version using the red PCB board, PCB size is 135.3*82.5mm.;
2. The front of the narrow edge placed with USB communication interface and DB9 hand control interface for the convenience of customers drawn from the case panel directly;
3. The back-end of narrow edge is power input and output interface and 3 relay output interface; relay is strong interference source, relay away from the design of main control chip, it is conducive to the stability of the board;
4. One of the two wide sides is stepper motor and principal axiscontrol signal output;
5. The another side of two wide sides is the emergency stop, manual speed input, limiting input interface; one side for the input, another side output connection mode is simple and convenient;
6. 5V and 12V power module compact independence, security, stability;
7. External ensure the stability of the system work effectively with crystal active and main control chip shield;
8.outline dimension is 135.3*82.5mm, product positioning hole installment dimension is 127*75mm
9. The software is USBCNC,not mach3,pls note!
This item is easy to operate for DIY hobby user,but it is control by USB port,so need more careful for the software install,and pls must be strict read the user manual and follow us.
2. FMD2740C stepper motor driver
3. Stepper Motor
General Specification:
Step angle accuracy:+ - 5%(full step,not load)
Resistance accuracy: + - 10%
Inductance accuracy:+ - 20%
Temperature rise: 80deg Max(rated current,2 phase on)
Ambient temperature ----------—20deg ---- +50deg
Insulation resistance:100ohm Min,500VDC
Insultion Strength--------500VAC for one minute
Datasheet
(23HS2430B,Front shaft 8mm dia and 21mm length;back shaft 8mm dia and 11mm length,425 oz-in or 28kg.cm holding torque)
Motor lead wires:
RED: A+
GREEN: A-
YELLOW: B+
BLUE: B-
4.Switching power supply
Shipping
· Please open the package and check if there are some damages before sign, if there are some damages,please do not sign and contact us immediately
· We ship to worldwide but if your country’s custom is strict, please contact us before you bid to check detail and confirmed.
· Please check out your address carefully when processing order.We are not responsible for wrong or undeliverable address.
Payment
· We accept paypal payment only.
· Payment must be made within 48hours of the auction end time
Problem&Feedback
· Please give us the opportunityto resolve any problem when you have,we concern your problem and we will try our best to resolve it.
· If you are not satisfied, please contact us to resolve any issues. Please do NOT leave negative feedback without asking for help. We work hard to make sure EVERY CUSTOMER 100% satisfaction.
· For any inquiries,issues or assistanceplease contact us via eBay message
Refund
· When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos to us.
· Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us
· Please feel free for any questions, all the emails will be replied within 1-2 business days,if you didn’t receive any mail, maybe it’s in the junk mail fold.
· We are online from Monday to Saturday.