DSLRKIT DIM4P2USG ALL Gigabit 7Ports 48V PoE Switch(2Uplink, 4PoE,1SFP)

ALL Gigabit 10/100/1000Mbps

Passive PoE Injector Switch
Midspan Mode-B Unsolicited Power 48V(4,5+/7,8-)

Per port Max 40Watt(48V0.84A) 

Power Total Output 96Watt(52V 1.85A)

Compatible 802.3at 802.3af
Support EXTEND mode, max Network Cable length to 250 meters

This is an Passive Power Over Ethernet switches, including 4 unsolicited PoE Ethernet ports and 2 Uplink ports and 1.25G SFP port. With an external 110V-240VAC to 52VDC power supply adapter, any one of the 1~4POE port can provide output power, each Ethernet port can provide network transmission speeds of up to 10/100/1000Mbps , with Cat5 / 5e / 6 network cable.

Which compatible with IEEE 802.3af/at Mode-B(4,5+/7,8-) POE switch device, but it does NOT include the 802.3af/at compliant detection feature.  It supplies power NO MATTER WHAT, so don't plug the "POE 1~4" side into anything that isn't ready for it.

Compatible all 802.3af/at device as Wireless Access Point, IP Phone, IP camera, Gateway , Switch, or More.....
UnifiAP: UAP-AC-LR and UAP-AC-LITE not Supported.

Notice:
This switch uses POE Mode B and cannot be used on the PowerDevice (PD) Device which only supports POE Mode A. The two new UniFIAP(UAP-AC-LR and UAP-AC-Lite) are known, so it is easy to tell the difference. For example, in the specification of UAP-AC-LR, it is written "PoE Mode 802.3AF /A" to indicate that 802.3AF standard A Mode is only supported.
If you are the user of UAP-AC-LR and UAP-AC-LITE,please go to my store to buy another 24V Gigabit POE Switch.

Note:
If your camera is with word “12V/PoE” as this picture shows, then please select this 52V PoE Switch, do not select 12V PoE Switch. 
Because "12V/PoE" means it can offer power supply to camera via 12V DC port or 48V(or 52V) PoE Ethernet port.

Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "PoE 1X~PoE 4X" port, this will damage your device..

NONE PoE gigabit ethernet device and Uplink device can only access "5~6x ports and SFP port"  Please do not access "PoE 1X~ PoE 4X", this will damage your device.

NOTE.
When EXTEND mode enable, the Max bandwidth for the Power Link (PoE) port 1-4 network port will be reduced to 10Mbps for each one. Please check your IP CAMERA's  bit stream setting. We recommend the value does not over 8Mbps(8192Kbps).
(The up-link is not affected, it will always working at 1000Mbps max speed)

Features:

• 6 x 10/100/1000Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 4-Ports PoE function(port 1-port 4)
• 1x 1.25G SFP Port
• Support EXTEND mode, max Network Cable length to 250 meters. 
  
• Midspan Mode-B Unsolicited Power 52V (4,5+/7,8-)
• Per PoE port Maximum current: 0.84A
  
• Supports PoE power up to 48W for all PoE ports, Per PoE port Max 40Watt(52V 0.84A)
• Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
• Full/half duplex transfer mode for each port.
• Wire speed reception and transmission.
• Up to 2K unicast address entities per device. Self-teaming, and table aging.
• PoE power on RJ-45
  Power+ : pin 4 & pin 5; Power- : pin 7 & pin 8
• AC to DC power supply
  Input: 100V~240VAC, 50Hz~60Hz. Output: 52VDC 1.85A
• Power Consumption
  2.0 watts(max with no PD device connected)
  96watts(4 PoE ports Total Max. 96Watt)
• Product Dimensions 130mm W x 60mm D x 30mm H
• Temperature
  Operation Temperature:0 ~40℃ (32 ~104℉)
  Storage Temperature: -40 ~70℃(-40 ~158℉)
• Humidity 
  Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing
  

Item Included:

  DSLRKIT DIM4P2USG 7 Ports Gigabit Ethernet PoE switch x1
  AC Power Adapter(DC OutPut: 52V/1.85A) x1
  AC Power Cable x1