Skoda 1.4, 1.6, 1.9 & 2.0 TDi
Front Crankshaft seal - Timing End
Fits Skoda Models: Fabia, Roomster, Octavia, Superb, Yeti & Rapid
Engine Codes: AMF, ASY, ASZ, ATD, AVB, AVF, AWX, AXR, AZV, BJB, BKC, BKD, BLS, BLT, BMM, BMN, BMP, BMS, BNM, BNV, BPZ, BSS, BSV, BSW, BXE, CAYA, CAYB, CAYC, CBBB, CBDB, CEGA, CFFB, CFGB, CFHA, CFHC, CFHF, CFJA, CLCA, CLCB, CLJA, CLNA
OEM Number: 038103085E
Inner Diameter: 35mm
Outside Diameter: 48mm
Thickness: 10mm
Right-Hand twist
PLEASE READ THIS FITMENT GUIDE BEFORE ASSEMBLY! CLICK HERE
* Important fitting information *
1. Only remove PTFE oil seals from their protective packaging immediately before installation, to protect them from dust and other contamination.
2. The sealing lip of PTFE oil seals is protected by a plastic sleeve, which can normally be used as an assembly aid. Therefore, the sleeve should remain in place until the seal has been installed.
3. If the seal is to be installed without the sleeve, use the special tool provided by the manufacturer.
4. Both the PTFE sealing lip and the shaft surface must be completely dry. Do not use any grease or oil.
5. The shaft may not exhibit any sharp-edged chamfers – if necessary, have the edges removed by an engine expert.
6. The shaft surface must be in a perfect condition – also here, possible damage must be repaired by an expert.
7. Position the assembly sleeve with the PTFE oil seal on the shaft.
8. Make sure that the sealing ring is aligned correctly – the sleeve must be located so that the seal can be pushed onto the shaft smoothly.
9. Push the sealing ring onto the shaft with an even motion.
10. When replacing, the PTFE lip of the new seal should not run in the same position as the old one.
11. You can now remove the assembly sleeve.
12. Do not start the engine sooner than four hours after installation – this permits the new sealing lip to adapt perfectly to the shaft.
The most frequent cause for failure is damage to the PTFE sealing lip during assembly. If the seal is installed without the help of a sleeve or special tool and is shifted or even turned inside out, reliable sealing will hardly be possible. Similarly, the use of oil or grease – as with classical oil sealing rings – will result in total failure of the PTFE oil seal immediately after installation.
Free next day delivery - UK Mainland only
If you require any assistance or would like to ask any questions, please click below
Engine Information |
Engine Codes |
AMF
ASY
ASZ
ATD
AVB
AVF
AWX
AXR
AZV
BJB
BKC
BKD
BLS
BLT
BMM
BMN
BMP
BMS
BNM
BNV
BPZ
BSS
BSV
BSW
BXE
CAYA
CAYB
CAYC
CBBB
CBDB
CEGA
CFFB
CFGB
CFHA
CFHC
CFHF
CFJA
CLCA
CLCB
CLJA
CLNA
|
Engine Size |
1422cc
1598cc
1896cc
1968cc
|
Engine Type |
3 cylinder 6v Turbo Diesel
4 cylinder 8v Turbo Diesel
4 cylinder 16v Turbo Diesel
|
OEM Part Number |
038103085E |
Competitor Part Number |
AJUSA 15083100
ASHUKI 182-576A
AUTOMEGA 301030085038E
CONTITECH V155560
CORTECO 20026412B
ELRING 155.560
ELWIS ROYAL 8456050
FAI AUTOPARTS OS1166
FAI AUTOPARTS OS1323
FEBI BILSTEIN 32471
JP GROUP 1119500200
MALO 912PTF
PAYEN NA5106
REINZ 81-34366-00
SWAG 30 93 2471
TOPRAN 109 383
VAICO V10-3275 |