PVC Paint UPVC Door Window Gutter Plastic Paint All Colours & Finish 400ml Spray

PVC Paint, UPVC, Door & Window, 400ml Spray Paint, Paint For Pvc Doors & Windows

PNT 1K UPVC paints are made to order. We use the latest technology in paint dispensing equipment to provide exceptional colour match accuracy - guaranteed to match.

 

Our high quality 1K single-layer pure acrylic resin paint can be applied by brushing, rolling or by spraying directly to UPVC windows, doors, and soffits.

 

PNT paints provide excellent coverage and adhesion to UPVC and other plastic substrates with good elasticity. The UPVC 1K acrylic resin paint has very fast drying time and provides an extremely hard tough durable finish with upto 5 years of UV and weather resistance.

 

Due to the high covering power even with difficult colour shades 1 - 1 ½ coats are sufficient.

 

PNT uses only the highest quality products from industry leaders MIPA to manufacture our paints. Up to 20% of MIPA UN21 thinners may be added to adjust the viscosity if required.

 

 

Specially Developed for PVC & UPVC

1K single-layer acrylic

Fast drying time

UV & weather resistant

Flexible, durable finish

 

Direction of use for the Aerosol

 

1)        Shake the can vigorously for 2-3 minutes until the agitator ball is free and mixing.

2)         Apply in cross coats at a distance of 25cm from the object, leaving 15 mins between each coat (at 20 degrees)

3)         Wait 1-2 hours until fully dry and fully cured.

4)         After use turn the can upside down and spray until the valve is clean, preventing the valve from clogging.

 

 

How to Paint uPVC Windows

 

Use masking tape and newspaper to cover any areas you don't want painting i.e., glass, window/door furniture.

Clean and degrease the windows to remove any dirt and grease. Hot soapy water and a kitchen scourer will do the job. Finish by wiping clean with a soft cloth or towel and leave to dry completely.

Now you need to key the uPVC surface. This is effectively a light sanding to improve adhesion for a longer lasting finish. Use a 180-grit sandpaper and lightly sand to take off any sheen. Once finished, brush the door and finish with a damp cloth to remove any dust. Leave to dry.

Apply the paint using the directions advised above.

 

PaintNuts Home

Revitalise your windows, doors, and plastic surfaces effortlessly with PaintNuts uPVC paints. 

Available in various sizes, including 250ml, 400ml Aerosol, 500ml, 1 Litre, and 2.5 Litre , our selection caters to your specific needs.

 

Whether you desire a matt, satin, or glossy finish, our paints have exceptional adhesion, durability, and long-lasting vibrancy. Transform your surfaces with ease and enjoy the flawless results that will withstand the test of time.

 

Explore Our Trending Colours

Our top trending uPVC paint colours encompass a vibrant palette that caters to modern aesthetics and timeless styles.

Experience the allure of our collection, which includes stunning neutrals like sophisticated Slate Grey and timeless Pure White, perfect for creating an elegant ambience.

 

Windows & Doors

PaintNuts uPVC Paint, the revolutionary solution that will breathe new life into your windows, doors, and other plastic surfaces.

 

Say goodbye to dull and worn-out doors. With PaintNuts uPVC Paint, you can easily transform your home or business with vibrant, long-lasting colour.

 

Conservatories & Cladding

Our uPVC paint's durability and UV / weather resistance makes it ideal for plastic cladding, facias, guttering and drain pipes.

 

PaintNuts uPVC Paint requires minimal maintenance, allowing you to enjoy your beautifully painted surfaces for years to come.

 

uPVC Paint Coverage

Our uPVC paint offers coverage of approximately 10-12sqm per litre for a single coat when using a paint brush.

For the front of a typical uPVC door, 250ml is sufficient per coat. We recommend two coats, so 500ml is generally enough.

For an average-sized window frame (1498mm x 736mm), approx. 250ml covers two frames with two coats.

A 400ml aerosol can covers around 2sqm per coat, so one can cover a typical uPVC door. We suggest two coats, meaning two 400ml aerosol cans are usually sufficient.

 

PaintNuts uPVC paint is specially formulated for uPVC and plastic. It has excellent adhesion and coverage, ultra-fast drying times and provides an extremely tough, durable finish that's weatherproof and UV resistant.

Our paints come ready to use - no primer, hardener or thinner required. Thanks to high covering power, two coats are sufficient for a long-lasting finish.

Our uPVC door and window paints are custom mixed to order to provide exceptional colour match accuracy – choose from over 5,000 colours, each available in a matt, satin or gloss finish.

PaintNuts uPVC paint works how you want it to - it's brushable, roller-friendly, available as an aerosol and suitable for spray guns (thinning is recommended for spray gun application).

Specially developed for uPVC

Quick & easy to apply

Ultra-fast drying time

Weatherproof & UV resistant

Extremely durable finish

PaintNuts uPVC paint is perfect for renovation and refurbishment or to modernise the appearance of your home. Painting your existing windows and doors is an easy, cost-effective way to give your property a facelift, improve curb appeal and add value without the expense of replacing existing units or the disruption of major works.

Suitable for a range of plastic surfaces and most appropriate for those found in an outdoor setting such as: uPVC windows & doors; uPVC garage doors; plastic fascia boards, soffets, guttering and drain pipes; plastic meter cabinets; plastic sheds; and plastic garden furniture.

 

Paint brush application

Our uPVC paint has a coverage of approx. 10 to 12sqm per litre for a single coat when applied with a paint brush. The exterior of a typical uPVC door requires approx. 250ml per coat. We recommend two coats, so 500ml is usually sufficient. 

Based on an 'average' window (736mm x 1498mm), approx. 250ml of paint would usually be sufficient to cover two window frames, with two coats of paint. 

Aerosol can application

A single 400ml aerosol can covers an area of approx. 2sqm for a single coat. To cover the exterior of a typical uPVC door requires one 400ml aerosol can per coat. We recommend two coats, so two 400ml aerosol cans are usually sufficient.

Based on an 'average' window (736mm x 1498mm), approx. one 400ml aerosol can of paint would usually be sufficient to cover three window frames, with two coats of paint. 

Spray gun application

When using a spray gun, we recommend that the paint be thinned by 15 - 25% using PaintNuts thinners. Coverage when using a gravity spray gun / HVLP is approx. 25 - 30 m2 per litre.

 

Directions when using paint brush / roller

1. SURFACE PREPARATION

Use a clean cloth with hot soapy water to remove any dust or dirt on the surface. Once dry use PaintNuts Degreaser to remove any stubborn contaminants, grease or wax. Use a light grit scotch cloth to 'key' the surface to take off the sheen and improve adhesion for a longer lasting finish.  Wipe down the UPVC surface with degreaser again to remove any residue and leave to dry.  Once dry, mask around the UPVC surface area with masking tape and paper ready for painting. Mix paint for at least 2 minutes prior to application to ensure colour consistency.

2. APPLICATION

Brush on in smooth strokes. Leave to dry for 15 minutes before applying a second coat. Once you’ve finished painting wait 15 minutes then carefully remove the masking tape, ensuring you pull the tape away from the painted edge not across it. Leave to dry for 1-2 hours before touching the frame and 72 hours before the windows can be cleaned.

PLEASE NOTE: Paint should not be applied in cold, damp weather – it will adversely affect the application, finish, and drying time. The recommended minimum temperature for painting is between 10°C and 25°C, preferably out of direct sunlight.

3. CLEANING & STORAGE

Remove as much paint as possible and clean equipment with white spirit.  Store indoors in a cool, dry location between 5°C and 25°C and out of direct sunlight. Use within 12 months once opened.

Directions for aerosol / spray can application

1. SURFACE PREPARATION

Use a clean cloth with hot soapy water to remove any dust or dirt on the surface. Once dry use PaintNuts Degreaser to remove any stubborn contaminants, grease or wax. Use a light grit scotch cloth to 'key' the surface to take off the sheen and improve adhesion for a longer lasting finish.  Wipe down the UPVC surface with degreaser again to remove any residue and leave to dry.  Once dry, mask around the UPVC surface area with masking tape and paper ready for painting. Shake the spray can vigorously for 2-3 minutes until the agitator ball is free and the paint is thoroughly mixed. Before applying the paint, we recommend testing the colour and adjusting the spray nozzle for either horizontal or vertical painting.

2. APPLICATION

Apply in smooth cross coats 250mm distance from the surface, either vertically or horizontally Leave to dry for 15 minutes before applying a recommended second coat Once you’ve finished painting wait 15 minutes then carefully remove the masking tape, ensuring you pull the tape away from the painted edge not across it.  Leave to dry for 1-2 hours before touching the frame and 48 hours before the windows can be cleaned.

3. CLEANING & STORAGE

After use turn the aerosol upside down and press to empty nozzle and valve, wipe the nozzle with a cloth to remove any excess paint, it can be reused at a later date. Remove as much paint as possible and clean equipment with white spirit.  Store indoors in a cool, dry location between 5°C and 25°C and out of direct sunlight. Use within 12 months once opened.

PLEASE NOTE: Paint should not be applied in cold, damp weather – it will adversely affect the application, finish, and drying time. The recommended minimum temperature for using spray paint is 15+ degrees, preferably room temperature in a warm and well-ventilated area.

 

Product Information

Brand – PaintNuts

Paint Type - Solvent-based, single component "1k" acrylic paint - no need for separate hardener.

Paint Base – Solvent

Suggested Surfaces - Suitable for: uPVC windows & doors; uPVC garage doors; plastic fascia boards, soffets, guttering and drain pipes; plastic meter cabinets; plastic sheds; plastic garden furniture; hard plastic garage doors (uPVC / ABS / GRP)

Finish Details - Available in the following finishes: Matt (10% gloss level), Satin (30% gloss level) or Gloss (90% gloss level).

Application Method - Brushable, roller-friendly, available as an aerosol and suitable for spray guns

Primer Required – No

Storage - Store indoors in a cool, dry location between 5°C and 25°C and out of direct sunlight. Shelf Life - Up to 2 years. Use within 12 months of opening.

Time Between Coats - Leave to dry for 15 minutes before applying a second coat if necessary

Drying Time - Dust dry in 10-15 mins Set to touch in 20-25 mins Fully cured in 1-2 hours Note: Drying times quoted above assume environment temperatures of 15 - 20 degrees celsius. Extreme temperatures and windy or damp conditions will affect drying times.

Weather Conditions for Painting - It’s important to apply paint in favourable weather conditions. Ideal temperature is between 10°C and 25°C.

Cleaning Instructions - Remove as much paint as possible and clean equipment with white spirit. See our Cleaning Instructions for more guidance. 

Safety Information

Warning: Contains flamable liquid and vapour. Causes serious eye irritation. May cause drowsiness or dizziness.  Keep out of reach of children and pets.  Solvent abuse can kill instantly.   See safety sheet via Downloads tab for more information. 

Hardener Ratio - No hardener required

Thinner Ratio - (Brush / Roller)Ready for use. No dilution required.

Spray Gun Suitable – Yes

Spray Gun Pressure (BAR) - 2.0 bar - 2.5 bar

Spray Gun Nozzle Size (MM) - 1.2mm - 1.3mm

Thinner Ratio (Spray Gun) - 15 - 25% dilution with PaintNuts thinners

VOC Regulation - This product contains a VOC-value of up to 550 g/l of VOC