gws led logo

 

GLASS

IP65

Bright

PTFE

Anti-Glare Tempered Glass

The anti-glare tempered glass helps to reduce the amount of glare that reflects off from the lenses.

IP65 Waterproof

With a weatherproof rating of IP65, it can be used outside even in the worst of weathers.

Super Bright

High power LED Chip provides instant illumination to a range of domestic and commercial outdoor spaces.

Plastic PTFE Respirator

Built-in respirator to clear away the mist and avoid dewing.

 

Casing Colour

BLACKGREYWHITE

 

How to change the colour? 

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

6000K

1. Default when first turned on would be Daylight (6000K).

3000K

2. Turn off unit and switch unit back on within 3 seconds to give Warm White (3000K).

4000K

3. Turn off unit and switch unit back on again within 3 seconds to give Neutral White (4000K).

 

 

 

 

 

 

 

 

 

 

 

 

 

 10W20W30W50W70W100W150W200W
Equiv. Halogen80W-100W150W-200W250W-300W350W-400W500W-600W700W-800W1300W-1400W1800W-1900W
Lumens900-10001800-20002700-30004500-50006300-70009000-1000013500-1500018000-20000
Dimension (L*W*H)mm110*90*20110*90*20140*110*25200*145*27215*157*25275*205*30313*233*30380*282*40

 

Casing Colour

BLACKGREYWHITE

 

 

How to change the colour? 

* Colour Setting can be done with or without PIR sensor attached.

A. Installed Without Switch: To set the colour, unit will need to be switched off and back on from the mains within 3 seconds.

B. With Switch: To set the colour on the light, simply follow instructions below:

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

6000K

1. Default when first turned on would be Daylight (6000K).

3000K

2. Turn off unit and switch unit back on within 3 seconds to give Warm White (3000K).

4000K

3. Turn off unit and switch unit back on again within 3 seconds to give Neutral White (4000K).

 

How to set the PIR sensor? 

The Time, Sensitivity and the Lux level are adjusted with the dials on the PIR sensor.

  • Turn the TIME dial anticlockwise to decrease the hold time (7 seconds－7 minutes).
  • Turn the SENS dial anticlockwise to decrease the detection range (8m±2m).
  • Turn the LUX dial anticlockwise to restrict activation to lower light conditions (<10-2000lux).

Note: When first switched on, the light will come on for approx. 20 seconds before entering sensor mode.

 

 

 

 

 

 

 

 


 

 

Casing Colour

BLACKGREYWHITE

 

How to change the colour? 

* Do not attach sensor, keep original blanking plug and cap in the unit when setting colour.

A. Installed Without Switch: To set the colour, unit will need to be switched off and back on from the mains within 3 seconds.

B. With Switch: To set the colour on the light, simply follow instructions below:

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

SURFACE MOUNTED ROUND BLUE EDGE LIT LED PANEL LIGHT

6000K

1. Default when first turned on would be Daylight (6000K).

3000K

2. Turn off unit and switch unit back on within 3 seconds to give Warm White (3000K).

4000K

3. Turn off unit and switch unit back on again within 3 seconds to give Neutral White (4000K).

 

Sensor Installation

  • Before fitting a sensor, turn off and isolate the floodlight to be worked on by removing the fuse or switching the circuit breaker off at the distribution board.
  • Rotate the cap on sensor mounting anticlockwise a ¼ turn and remove (1).
  • Pull out the blanking plug (2).
  • Align the pins on the sensor with the holes, taking care that the bump on the inside of the collar also lines up with the slot on the mounting, then push to fit and rotate the collar clockwise a ¼ turn to seal (3).
We would advise, before permanently installing the light, is to turn the unit on and pre-select the desired colour output. Especially, if you have multiple units on a single switch, in an event that one unit may have a different sequence preset. For example, if you have 3 units installed onto a single switch, if colours on each are not pre-selected, they may differ from one another, you would not be able to synchronise the 3 units as they all have memory function.

 

 

 

 

 

 

 

 


 

 

 

GLASS

IP65

Bright

PTFE

About Us

G.W.S LED is a UK-based developer and manufacturer of LED lighting, offering a broad variety of LED products for lighting professionals as well as end users. Our products undergo a certified quality standards procedure to make sure we only stock items with the newest and most reliable technology.

Payment

Our preferred method would be Paypal but we can also accept all major credit/debit cards payment and direct bank transfers. If you use e-cheque on PayPal, delivery may take longer, as we will not be able to process your order until the e-cheque clears. We are a VAT registered company so a VAT receipt can be provided with your purchase.

Shipping

Items will be shipped within 1-2 business days (Monday-Friday) following order completion. We offer Free UK Standard Delivery. However, if you simply can’t wait to get your hands on the product, we have Express Delivery option available for you.

Returns

If the items we sent to you is incorrect, or your items have arrived with a manufacturing defect, please contact us within 14 days where we will always offer you the choice of an exchange or refund. If you wish to return unused goods for refund or exchange, they must be returned with their original packaging within 30 days. We will only pay the postage price for any goods that need to be resent due to a fault on our behalf.