for Arduino XL4016 DC-DC Buck Module 5-40V To 1.2-35V Step Down Converter

 



29. Wiring Method: amphenol connector
7. Lowest pressure: 1V
12. Input 24V output 12V 5A ripple around 50mV (Excluding noise)
2. Input voltage: DC 7-32V
such as constant current value is 3A, turn the lamp current is set to a constant current is 0.1 times (0.1 * 3A = 0.3A).
28. Output prevent reverse flow: NO
3. Output voltage: (1) DC 0.8-28V continuously adjustable. (2) Fixed output:Choose between 0.8v-28v
5. Constant current range: 0.2-8A ( adjustable )
to 60 degrees, the constant current value change is less than 5% (5A constant current value)
11. Output ripple: 20M bandwidth
19. Voltage regulation: ± 1%
13. Output short circuit protection : Yes, constant current
6. Turn lamp current: Constant current value * ( 0.1 ) , turn the lamp current and constant value linkage,
21. Potentiometer adjustment direction: clockwise (increase), counterclockwise (decrease), the potentiometer (CV) closed to the input voltage is used to regulate voltage, the potentiometer (CC) closed to output voltage is used to regulate current (CC)
14. Input reverse polarity protection: None
1. Module properties: Non-isolated step-down constant current, constant voltage module (CC CV) charging module
15. Output prevent backflow: None
Brand New and High Quality
22. Operating temperature: Industrial grade (-40 °C to +85 °C) ( please note the actual use of the power tube temperature , high temperature heat strengthened)
8. Output Power: Maximum power is about 300W
27. Input reverse connect protection: NO
26. Output short circuit protection: Yes,Constant current (the current setting constant current value)
24. Size (approx): 65 x 47 x 20mm (L x W x H)
23. Indicator: dual color indicator, charging indicator light is red, the green light means fully charged ( No load is green )
20. Dynamic response speed: 5% 200uS
10. Operating frequency: 300KHZ
17. No-load current: Typical 20mA (24V switch 12V)
18. Load regulation: ± 1% ( constant )
9. Conversion efficiency: Up to about 95%
25.Precision of constant current and temperature: On the actual test, the module temperature from 25 degrees
4. Output Current: 8A (when power tube's temperature exceeds 65 degrees, please add cooling fan)
16. Wiring: Terminal
Features:
1. Fixed turn lamp current is 0.1 times the current value ( Used to identify whether the battery is fully charged When charging).
2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver.
3. High output current, the max output current can reach 8A.
4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization.
5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other.
6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever.
7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability.
8. Double color lamp, working condition be clear at a glance
9. Voltage and current are adjustable,wich effect is good.
Applications:
1. High-power LED driver.
2. Lithium battery (or lead accumulator) charge.
3. Vehicle-mounted power supply.
4. Low voltage system power supply.
5. 6V, 12V, 14V, 24V battery charge.
6. On-board laptop power supply.
7. regulated power supply.
8.Low voltage power supply system.
Battery charge:
1. Make sure of the battery float voltage and charging current that you need, as well as the input voltage of the module.
2. Adjust the constant voltage potentiometer and adjust the output voltage to about 5V.
3. Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make the output current to the expected charging current value.
4. Adjust the constant voltage potentiometer to make the output voltage reaches the float voltage.
5. Connected to the battery, try to charge.
(1,2,3,4 steps to connect the power module input,output no-load does not connect battery.)
LED constant current drive:
1. Make sure the operating current and Max operating Voltage of the LED you need to drive.
2. Adjust the constant voltage potentiometer, adjust the output voltage to about 5V.
3. Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected LED operating current.
4. Adjust the constant voltage potentiometer to make the output voltage reach the maximum LED operating voltage.
5. Connect LED, test.
(1,2,3,4 steps to connect the power module input, output No-load does not connect LED.)
Notice:
1. The real color of the item may be slightly different from the pictures shown on the website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data. Thank for your understanding.
3. 1cm=0.39''.
Package Included:
1x Step Down Module


* Please make payment asap, then we can arrange shipment for you asap.


- Thanks for your bid

* We will arrange shipping for you within 24 Hours after payment cleared except the holidays.

* If you have changed your address, or want us to ship to another address, please change to the new address.

* We ship items to Worldwide. Thank you. 



- International Buyers Please Note: 

*  Please check with your country customs office to determine what these additional costs will be prior to bidding/buying

* We will carefully test every item before shipment.The quality is guaranteed!



- Our working time:

* Hong Kong time : Monday to Saturday 8:30 am to 5:30 pm.
* if you send email to us,In our working hours will be resumed within 24 hours.
* If you we are not satisfied with us ,please contact me and don't give us negative or natural feedback,We must give you a satisfactory solution.




* You can contact us through email
 

On 16-Mar-2023 at 16:43:15 GMT, seller added the following information:

DataCaciques