ECUMASTER 5" ADU ADU5 IP65 Digital Dash Display & Pre Made Loom & GPS & USB to Can Kit

You are buying a 5" ADU & Pre MADE Loom & GPS & Can to USB BOX 

We are proud to announce the new ECUMASTER Racing Dash family of products. We designed the ADU5 and ADU7 in response to market demand for a cost-effective dash display with logging capabilities. Our specific goal was to create a fully customizable, feature-rich, quality solution for competitive drivers. We consulted professional drivers and race engineers and designed the ADU to exceed their requirements.

Above all, the ADU is designed to display all critical information in an easy to read manner, along with a comprehensive strategy for displaying alarms.

Our Advanced Display Units are available in 5” and 7” versions. Both versions feature high resolution, high visibility anti-glare screens, guaranteeing perfect visibility in any lighting conditions. The ADU comes with multiple pre-configured pages, which can be customized by the end user to display data required at every race stage (e.g. practice, qualification, race, troubleshooting, etc.). Pages may be changed manually or automatically (based on defined conditions). Each channel displayed on a page (gauges, icons, texts, etc.) can be easily modified in real time using user-friendly Windows based software. Our comprehensive overlay system facilitates a multiple page display for important data (e.g. low oil pressure, best lap, etc.) independent of the actual page displayed.

The ADU is also equipped with 15 ultra-bright RGB LEDs which can be used as an advanced gear-depended shift light and can be modified by user-defined logic (for alarms, low fuel level, etc.).
Using IR beacons or a GPS system, the dash turns into a powerful lap timer with a predictive timing function. By selecting the Qualification page, you enable a “Qualification Mode” which uses advanced predictive lap timing based on an automatically updated “best” reference lap.

User configurable timers can be adjusted for additional functionality (pit stop timer, etc.). The ADU also supports thermal cameras for monitoring brake discs or tyre temperatures (up to 16 points per tyre).
Communication with other devices in the car is provided via two built-in, independent CAN-BUS communication ports. CAN templates are provided for most popular ECUs, and are fully configurable, allowing you to connect our hardware to virtually any engine management system.
To ensure that all features work seamlessly, our device is based on a 32-bit automotive controller paired with a state of the art graphics processor. This combination provides the perfect working environment for any engineer or driver and guarantees anti-aliased, high-quality graphics at 50 frames per second.
For further data analysis, data channels can be logged to a USB Flash drive with a frequency of up to 500Hz.
All of these “Must Have” features and more are housed in a rugged, specially CNC machined, black anodized enclosure.

Free, easy to install firmware upgrades further improve system capabilities (e.g. new strategies, Trigger patterns, CAN data streams).

Supported ECUS:

AEM - Autronic SM4 - DTA Fast S Series - ECUMASTER CLASSIC BLACK - ECUMASTER PMU- EMTRON - EVO X - Hondata Kpro - Life Racing - Link ECU - Megasquirt- Motec M400 M600 M800 M1 - Pectal SQ-6 - Syvecs - Vipec - OBD2 over can ECUS - Any ECU able to send info over Canbus.

SPECIFICATION

GENERAL
Temperature range	AECQ100 GRADE1 (-40 to +85˚C)
Reverse battery protection	Yes, internal
Operating voltage	6-22V, immunity to transients according to ISO 7637
Enclosure	IP 65, custom CNC machined aluminum
Connectors	1 x 35 positions, AMP Automotive connector
PC communication	CAN BUS – Ecumaster interface, Peak or Kvaser
Display Type	TFT 800×600
Brightness of display	5″ – 600 cd/m2, 7″ – 1000 cd/m2
INPUTS / OUTPUTS
Analogue inputs	8 inputs, 10 bits, 0-5 V, software controlled pull-up/pull-down 10K resistor. Al analog inputs can be used as a switches
Digital inputs	8 digital inputs, software controlled input sensitivity (VR, Hall), software controlled 4K7 pull-up resistors, used for engine speed sensors, Flex Fuel, wheel speeds, turbocharger shaft speed. All digital inputs can be used as switches
Outputs	2 low side outputs (switch to ground), up to 2A, 1 analogue output (0-5V) 10 bits
+5V Output	Monitored 5V output for powering external sensors
COMMUNICATION
CAN Interface	2 x CAN2.0 A/B, 250, 500, 1000 Kbps
CAN streams	User-defined
Serial communication	RS232 Rx/Tx, AiM protocols, Ecumaster, Hondata Kpro, Autronic
USB	Used for logging to external USB memory
OTHERS
Light Emitting Diodes	15 ultra bright RGB LEDs
Accelerometer/gyroscope	3D accelerometer + 3D gyroscope for the analysis of vehicle dynamics
Real-time clock	Yes, battery powered
Light sensor	Yes, for automatic correction of brightness
Temperature sensor	Yes, for monitoring device temperature

GPS Specification : This GPS to CAN module provides the CAN system with GPS data. This data can be used for data logging, lap timer and speed/acceleration.

USB to CAN Specification: The ECUMASTER USB to CAN is a USB interface that allows the user to connect to the CANbus network. It supports CAN 2.0A and CAN 2.0B standards. It is equipped with a LED status diode for fast diagnostic and a 120 Ohm terminator that can be switched on or off to relieve the user from applying external terminators.

CAN to USB interface, this product is necessary for communicating to the PMU & ADU as listed in the shop index, this product is also used for tracing live logging of CAN bus messages

*Required to configure ADU OR PMU

Pre Made ADU Dash Loom Spec:

A loom pre built for your ECUMaster ADU5 or ADU7, using the original AMPSEAL connector. Taking away the stress of wiring in your own dash.

Fitted with:

• 2 options for switches, these can be used for resetting page values and swapping pages. (Switches will be a random colour or finish and will need connecting by the user due to mounting them)
• A connector on the end of a 1200mm length is used to connect power, ground and CANBUS. Including a GPS connection
• Included as well is a port ready for CAN communication using the ECUMaster USB to CAN and a USB port to record your logs from the ADU.

The loom is wrapped in cable sleeve to give it a smart look and keep all wiring neat

All Items are shipped by a 1st class postage or 24 hour courier. 

Any Items That Are Out Of Stock Or have Extended Lead Times, May Take Slightly Longer Than Normal.

Thanks You

Why buy from us? Consistent Quality and Customer Service:

• Be confident you will get what you ordered; and if by chance a problem occurs we fix the issue very fast with no quibbles!

• Get the item quickly and cheaply: Most of our items are either Free or Carry a small nominal fee!

• Know it will be easy to return. Your purchased item can be returned in line with eBays best practices and being a small business we will always look to solve issues even after these periods.

• Buy items hassle free – Just look at our feedback to see how good we really are!

Postage and Packaging:

• We use high quality bubble lined jiffy bags for all small order to ensure a damage free transit & High Quality Double Walled Boxes for the heavier & larger items.

• All UK Orders are Sent Via 1st class service or 24 hour courier, All orders are fully insured. Posted within 24 hours unless advert dispatch time or description states otherwise. Orders before 3pm are usually sent same day.

• International Orders are sent Via DHL EXPRESS. All tracking will be added to the order details as soon as it is obtained.

• Tracking numbers automatically attach to every order once dispatched

• It’s important to make sure PayPal and EBay postage addresses are up to date as these are the addresses we send to only.

Problems should they occur:

• We go to great lengths to ensure mistakes are not made, however we are only human; So if there is any issues with your order please drop us a message, email or phone call and we will get it correct as soon as possible.

• If you think there is anything we can do to improve our services or product we would love to hear from you- Seriously we can only improve if we have input from our customers.

Feedback:

• We use an automated system that leaves feedback as soon as it is received, this ensures the transaction is complete and you are 100% happy with our service.

• If you feel that we do not deserve 5 Stars for any reason, please contact us and explain before leaving feedback as we may be able to correct any issues you may have :)

Advice:

• Any queries about any item/ postage etc is free, Drop us a message and ask away, there is also a lot of information over on our Facebook Page.  

We are always happy to help :)

SHOP BHP is a Trading Name of Brands Hatch Performance LTD