Odroid-HC4 Home Cloud 4GB RAM Amlogic S905X3 1.8GHz Quad Core

Just like the Odroid-C4, the Odroid-HC4 also carries the 1.8 GHz Amlogic S905X3 ARM Cortex-A55 Quad-Core processor with Mali G31 MP2 Graphics Processing Unit. The Odroid-CH4 board features the Home Cloud support. With a DDR4 4GB RAM, the Odroid-HC4 carries an SPI 16MiB flash chip with Petitboot support. Note: This HC4 Variant DOES NOT include OLED What is new with Odroid-HC4 The Odroid-HC4 has a consistent SATA bridge solution (PCIe to SATA) rather than the USB3.0 to SATA. By this, the HC4 becomes capable of supporting 2x SATA storage docks. This board has a transparent case that has cutouts for board interfaces and ports. Specifications of Odroid-HC4 Home Cloud RAM 4GiB DDR4 Grade: PC4-21333 But width: 32-bit Data Rate: 2640 MT/s Low Power Design: 1.2Volt External Input / Output HOST USB 2.0 Port (x1) SATA Connectors (x2) UART Serial Debug Console (x1) Processor 32 KB L1 instruction cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines 32 KB L1 data cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines 512KB L3 data cache, 512 sets 16-way set associative, 4 processors share 64 byte lines Amlogic S905X3 12nm Architecture: ARMv8-A with Crypto and Neon extensions Mali-G31 MP2 GPU (650MHz) 4x Execution Engines General IR receiver for infrared remote control System Indicator LEDs BLUE (Flashes when Kernel is running) RED LED for PWR (DC Power Connected) Power 5V ~ 15.5V DC Input 15V / 4A DC Power Adapter Recommended (Not Included) 1x DC Power Jack: 5.5mm (negative / outer) and 2.1mm (positive / inner) diameter Power Consumption with 2x HDDs (ST2000DM006) Suspend Mode: Nearly 0.29 W IDLE Mode: Nearly 5.88 W (when HHD is in Spin-Down) Active Mode: Nearly 15.59 W (while using SAMBA) Form Factor Measurements of HC4 Board: 90.5mm x 84mm x 25mm HC4 weighs 280 grams (including the case, fan, and heatsink) General For infrared remote control, there is an IR receiver System Indicator LEDs BLUE (Flashes when Kernel is running) RED LED for PWR (DC Power Connected) Storage 1x Micro SD Slot (Compatible with DS/HS mode and supports UHS-1 SDR104) Networking 1x RJ45 GbE LAN Port | supports 10/100/1000 Mbps Amber LED: 1000Mpbs connection data traffic indicator Green LED: 100Mpbs connection data traffic indicator RTL8211F Realtek Ethernet Transceiver Video 1x HDMI 2.0 Port with HDR, EDID, CEC | up to 4K @ 60Hz Audio 1x HDMI Digital Audio Output Heatsink A passive heatsink on the processing unit Measurements: 4cm x 3.2cm x 1cm Cooling Fan A Hydraulic Bearing Fan Maximum Rotations Per Minute (RPM): 4000 Rotations Air Flow: 4.3 CFM Noise Level: 23.9 dBA Connector and Wire: 1.25mm Pitch 4-Pin, 80mm Current Rating: 100 mA Voltage Rating: 5V Air Pressure: 0.053 in H2O Measurements: 4cm x 4cm x 1.06cm Odroid-HC4 Software Compatibility Petitboot is efficient at automatically locating the OS on the SSD, HDD, or SD Card. For instance, if no SD Card is attached, the Petitboot uses the attached SSD or the HDD to boot the Odroid-HC4 in case the OS is installed on both or any one of these connected storages. The Operating System Image from Hardkernel which is already installed is suitable with Ubuntu and Debian Operating Systems. Ubuntu or Debian Netboot installer can be used too. The Odroid-HC4 backs the following versions of Linux Kernel: Mainline Kernel (unofficial) version 5.8 or greater Hardkernel Stock Operating System version 4.9.230 or greater

Odroid-HC4 Home Cloud 4GB RAM Amlogic S905X3 1.8GHz Quad Core

Note: This HC4 Variant DOES NOT include OLED

What is new with Odroid-HC4

The Odroid-HC4 has a consistent SATA bridge solution (PCIe to SATA) rather than the USB3.0 to SATA. By this, the HC4 becomes capable of supporting 2x SATA storage docks. This board has a transparent case that has cutouts for board interfaces and ports.

Specifications of Odroid-HC4 Home Cloud

RAM
- 4GiB DDR4
- Grade: PC4-21333
- But width: 32-bit
- Data Rate: 2640 MT/s
- Low Power Design: 1.2Volt
External Input / Output
- HOST USB 2.0 Port (x1)
- SATA Connectors (x2)
- UART Serial Debug Console (x1)
Processor
- 32 KB L1 instruction cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines
- 32 KB L1 data cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines
- 512KB L3 data cache, 512 sets 16-way set associative, 4 processors share 64 byte lines
- Amlogic S905X3 12nm
- Architecture: ARMv8-A with Crypto and Neon extensions
Mali-G31 MP2 GPU (650MHz) 4x Execution Engines General
- IR receiver for infrared remote control
- System Indicator LEDs
  - BLUE (Flashes when Kernel is running)
  - RED LED for PWR (DC Power Connected)
- Power
  - 5V ~ 15.5V DC Input
  - 15V / 4A DC Power Adapter Recommended (Not Included)
  - 1x DC Power Jack: 5.5mm (negative / outer) and 2.1mm (positive / inner) diameter
- Power Consumption with 2x HDDs (ST2000DM006)
  - Suspend Mode: Nearly 0.29 W
  - IDLE Mode: Nearly 5.88 W (when HHD is in Spin-Down)
  - Active Mode: Nearly 15.59 W (while using SAMBA)
- Form Factor
  - Measurements of HC4 Board: 90.5mm x 84mm x 25mm
  - HC4 weighs 280 grams (including the case, fan, and heatsink)
- General
  - For infrared remote control, there is an IR receiver
  - System Indicator LEDs
    - BLUE (Flashes when Kernel is running)
    - RED LED for PWR (DC Power Connected)
  - Storage
    - 1x Micro SD Slot (Compatible with DS/HS mode and supports UHS-1 SDR104)
  - Networking
    - 1x RJ45 GbE LAN Port | supports 10/100/1000 Mbps
    - Amber LED: 1000Mpbs connection data traffic indicator
    - Green LED: 100Mpbs connection data traffic indicator
    - RTL8211F Realtek Ethernet Transceiver
  - Video
    - 1x HDMI 2.0 Port with HDR, EDID, CEC | up to 4K @ 60Hz
  - Audio
    - 1x HDMI Digital Audio Output
  - Heatsink
    - A passive heatsink on the processing unit
    - Measurements: 4cm x 3.2cm x 1cm
  - Cooling Fan
    - A Hydraulic Bearing Fan
    - Maximum Rotations Per Minute (RPM): 4000 Rotations
    - Air Flow: 4.3 CFM
    - Noise Level: 23.9 dBA
    - Connector and Wire: 1.25mm Pitch 4-Pin, 80mm
    - Current Rating: 100 mA
    - Voltage Rating: 5V
    - Air Pressure: 0.053 in H2O
    - Measurements: 4cm x 4cm x 1.06cm

Odroid-HC4 Software Compatibility

Petitboot is efficient at automatically locating the OS on the SSD, HDD, or SD Card. For instance, if no SD Card is attached, the Petitboot uses the attached SSD or the HDD to boot the Odroid-HC4 in case the OS is installed on both or any one of these connected storages.

The Operating System Image from Hardkernel which is already installed is suitable with Ubuntu and Debian Operating Systems. Ubuntu or Debian Netboot installer can be uséd too.

The Odroid-HC4 backs the following versions of Linux Kernel: