MST-90+ Universal Car Battery Voltage Regulator Charger for ECU Coding Power Stabilizer
Specifications:
Automotive Programming Dedicated Power Output
DC voltage: 14.2V
Rated current: 120A
Rated power: 1700W
Ripple and noise: 100mVp-p
Automotive Programming Dedicated Power Input Characteristics
Rated input voltage: 220V or 110V (+/-20%)
Frequency range: 40-60HZ
Power factor: 0.95
Efficiency: 85%
Automotive Programming Dedicated Power Protection Features
Overload: 90-110% of rated output power
Over-voltage: 15V
Operating temperature: -40 - +70 C
Safety: UL60950, TUV EN60950-1
Withstand Voltage: I/P-O/P:3KVAC I/P-FG:1.5KVAC
Insulation resistance: I/P-O/P, I/P-FG:100M Ohms, 500VDC/25 /70%RH
EMC: EN55022, EN61000
Note : please don't start the engine during the process of power charging to the vehicle to avoid damage to the device caused by adverse charging
This charger is only suitable for 12V lead-acid battery charging
Operating instructions:
l: Connect the charger power supply input line and battery charging line, and turn on the power supply while the the four indicator lights under the machine will flashing at the same time once, then went out together.
LCD display: Voltage: 14.20V; Current: 1.8 A; MST-90+
If the device does not detect the battery or the connection is incorrect, it means there is no voltage output. Then need connect to the battery (or press the FORCF START button). When the below indicator light WORK up, it means device normal operating.
LCD display: battery bad no battery; MST-90+
Turn off the power at the same time the ALAR and WARN indicator light will light up(with the sound di di di). LCD display: BMW BENZ AUDI battery bad no battery; Power OFF!
The output voltage is adjusted by the long press MODE button 3 seconds.
Press the FORCF START button to increase the voltage, press the MODE button to reduce the voltage. When the adjustment is completed ,it will exit the voltage regulation by pressing the MODE button for 3 seconds.
LCD display : Voltage:14.38V; Current: 63.1A; Adj. Voltage!
2: When the battery is charging over or when the charger output current is lower than 3A or,it will display BATT FULL/DISAB..When the current is restored to 3.5A,the BATT FULL/DISAB prompt disappears.
3: When the charging current is over 100A or the output voltage of the device is higher than 15V,the device will automatically disconnect the DC output and at the same time illuminate the ALARM while the WARN indicator flashes,accompanied by drops of alarm sound.The display shows"Temper High"or"Current High". When the current or voltage back to the normal range,click the FORCF START button,will stop drip alarm.
4: When the internal temperature of the device is higher than 76℃,then “WARN” will start and sounds an alarm. When the temperature is over 80 ℃, the "Temper High" will be displayed, and the output will be disconnected
5: When the input of the equipment is over current or over voltage,it will burn out the inner tube. Please check the input current & voltage and then use.
6: When the charger is turned on, the fan 1 is located at the back end of the machine,and the fan 2 can start at the same time.Ensure that the charger does not stop working and damage due to overheating.
Note:
1: Please use 10A or above of the power supply socket connected to the equipment. Please abide by the general rules of the safe use of electricity. A power supply socket with a ground wire must be used.
2: Verify that the connection between the positive and negative poles is correct when connecting the clip cable to the battery or vehicle.
3: After charging the wire into the connector, please tighten the right and ensure that the connection is reliable and then turn on the power switch.
4: The machine has high pressure, non professionals do not operate, so as not to shock.
5: This charger is only suitable for 12V lead-acid battery charging.
Package Included:
1 x MST-90+ Car Battery Voltage Regulator Charger (1pc Only)
1 x Cable with Red Clip (1pc Only)
1 x Cable with Black Clip (1pc Only)
1 x Power Input Cable (1pc Only)
Notes:
1. Due to the manual measurement and measurement unit conversion, please allow 1-3 unit deviations.
2. Due to the monitors used will not be calibrated the same and the lighting, product color showed in photos may look slightly different from the actual object.
3. Please contact us before purchasing if you are not familiar with the product.
4. Legal Disclaimer: (for our protection) We shall held no responsibility or accountability for damages or injuries as a result of using this product. We will also not guarantee the longevity, safety, or functionality of this product or any other products that we sell. You should bear all the risk for buying, using and possessing our products.
Automotive Programming Dedicated Power Output
DC voltage: 14.2V
Rated current: 120A
Rated power: 1700W
Ripple and noise: 100mVp-p
Automotive Programming Dedicated Power Input Characteristics
Rated input voltage: 220V or 110V (+/-20%)
Frequency range: 40-60HZ
Power factor: 0.95
Efficiency: 85%
Automotive Programming Dedicated Power Protection Features
Overload: 90-110% of rated output power
Over-voltage: 15V
Operating temperature: -40 - +70 C
Safety: UL60950, TUV EN60950-1
Withstand Voltage: I/P-O/P:3KVAC I/P-FG:1.5KVAC
Insulation resistance: I/P-O/P, I/P-FG:100M Ohms, 500VDC/25 /70%RH
EMC: EN55022, EN61000
Note : please don't start the engine during the process of power charging to the vehicle to avoid damage to the device caused by adverse charging
This charger is only suitable for 12V lead-acid battery charging
Operating instructions:
l: Connect the charger power supply input line and battery charging line, and turn on the power supply while the the four indicator lights under the machine will flashing at the same time once, then went out together.
LCD display: Voltage: 14.20V; Current: 1.8 A; MST-90+
If the device does not detect the battery or the connection is incorrect, it means there is no voltage output. Then need connect to the battery (or press the FORCF START button). When the below indicator light WORK up, it means device normal operating.
LCD display: battery bad no battery; MST-90+
Turn off the power at the same time the ALAR and WARN indicator light will light up(with the sound di di di). LCD display: BMW BENZ AUDI battery bad no battery; Power OFF!
The output voltage is adjusted by the long press MODE button 3 seconds.
Press the FORCF START button to increase the voltage, press the MODE button to reduce the voltage. When the adjustment is completed ,it will exit the voltage regulation by pressing the MODE button for 3 seconds.
LCD display : Voltage:14.38V; Current: 63.1A; Adj. Voltage!
2: When the battery is charging over or when the charger output current is lower than 3A or,it will display BATT FULL/DISAB..When the current is restored to 3.5A,the BATT FULL/DISAB prompt disappears.
3: When the charging current is over 100A or the output voltage of the device is higher than 15V,the device will automatically disconnect the DC output and at the same time illuminate the ALARM while the WARN indicator flashes,accompanied by drops of alarm sound.The display shows"Temper High"or"Current High". When the current or voltage back to the normal range,click the FORCF START button,will stop drip alarm.
4: When the internal temperature of the device is higher than 76℃,then “WARN” will start and sounds an alarm. When the temperature is over 80 ℃, the "Temper High" will be displayed, and the output will be disconnected
5: When the input of the equipment is over current or over voltage,it will burn out the inner tube. Please check the input current & voltage and then use.
6: When the charger is turned on, the fan 1 is located at the back end of the machine,and the fan 2 can start at the same time.Ensure that the charger does not stop working and damage due to overheating.
Note:
1: Please use 10A or above of the power supply socket connected to the equipment. Please abide by the general rules of the safe use of electricity. A power supply socket with a ground wire must be used.
2: Verify that the connection between the positive and negative poles is correct when connecting the clip cable to the battery or vehicle.
3: After charging the wire into the connector, please tighten the right and ensure that the connection is reliable and then turn on the power switch.
4: The machine has high pressure, non professionals do not operate, so as not to shock.
5: This charger is only suitable for 12V lead-acid battery charging.
1 x MST-90+ Car Battery Voltage Regulator Charger (1pc Only)
1 x Cable with Red Clip (1pc Only)
1 x Cable with Black Clip (1pc Only)
1 x Power Input Cable (1pc Only)
Notes:
2. Due to the monitors used will not be calibrated the same and the lighting, product color showed in photos may look slightly different from the actual object.
3. Please contact us before purchasing if you are not familiar with the product.
4. Legal Disclaimer: (for our protection) We shall held no responsibility or accountability for damages or injuries as a result of using this product. We will also not guarantee the longevity, safety, or functionality of this product or any other products that we sell. You should bear all the risk for buying, using and possessing our products.