Dr.Silver Mini is the latest generation device for obtaining water enriched with silver ions. The use of the latest technologies makes the process extremely efficient and much more dynamic compared to other familiar models. This makes it possible to achieve a high concentration of silver ions in the water in a short time. As a result of the high speed and activity of the process, it is possible to form a precipitate of silver colloid (atomic silver) at the bottom of the vessel, which is a guarantee of high efficiency. Therefore, mix the silver water well before use.
Purpose
The device can process water with a volume of 0.2 to 10 liters, and in some cases even larger quantities.
Specifications
- Silver productivity - 0.15 mg/min.
- Volumes of processed water - from 0.2 to 10 liters.
- Silver electrode resource - more than 50 hours of work.
- Volume of water treated with the device until the resource of the silver electrode is exhausted - 10,000 liters at a concentration of 0.05 mg/l.
- Temperature of treated water: from +5° to +40°C.
- Power source - battery 6F22 9V
- Mass of the silver anode, sample 1000 - 0.5 g +/- 0.05 g.
- Overall dimensions of the control unit: 95 x 54 x 18 mm.
- Overall dimensions of the electrolysis cell: 58 x 16 mm.
- Mass of the set with battery - 95 g.
Complete set:
Device for silver water, Dr.Silver Mini - 1 piece
Electrolytic cell - 1 piece
Technical description - 1 piece
Packaging - 1 piece
Working principle
The action of the device is based on the electrolytic dissolution of silver in water when current flows between silver and stainless electrodes. At the same time, colloidal silver ions accumulate in the water, the concentration of which is proportional to the processing time and the strength of the current. Solutions have been used in the design of the device that exclude any harmful impact on the user if the recommendations in the attached technical description are followed.
Method of use:
The device consists of a control unit (fig. 1) and an electrolytic cell (fig. 2). The control unit contains an electronic circuit controlling the process of electrolytic separation of silver ions (Ag+) and a power source 9V battery.
The electrolysis cell (Fig. 2) consists of two electrodes - anode 1 and cathode 2. The anode is made of silver sample 1000, and the cathode is made of stainless steel, certified for contact with drinking water. As a result of the electrolysis, the silver electrode gradually dissolves in the water. After prolonged operation, the silver is visibly reduced (Fig. 3) and the cell must be replaced. A new cell can be purchased from the manufacturer.
Before use, unpack the device. If it has been brought in from outside with a low temperature, it needs to be left at room temperature for a minimum of one hour before switching on to prevent damage or malfunction.
Wash the plastic tip, silver and stainless electrodes of the electrolysis cell thoroughly with liquid detergent and warm water. Rinse it well under running water. Attach the electrolysis cell coupling to the unit.
Using the following table, determine the treatment time for your required volume of water with the desired concentration of silver ions.
IMPORTANT!
Treated water must be clean, with low hardness, filtered or boiled. The use of very hard or highly contaminated water may impair the correct operation of the appliance.
If you need to process a larger volume of water, we recommend preparing a small amount of highly concentrated silver water, then mixing it well with the rest of the water.
Example:
You wish to prepare 10 liters of water with a concentration of 0.075 mg/l. To do this, fill a 10-liter container with water (for example, a mineral water bottle). Pour about one liter of this water into another container. Place the electrolysis cell in the water and turn on the device for 5 minutes. You will receive one liter of water with a concentration of 0.75 mg/l. Pour this water into the first container and mix (shake) well. This will give you 10 liters of water with a concentration of 0.075 mg/l.
Note: When working with high concentrations!
When a small amount of water is processed for a long time and the electrolysis cell is in contact with the bottom of the vessel, it is normal for a dark spot or whitish precipitate to form on the bottom of the vessel. This is due to a partial precipitation of silver colloid in the form of atomic silver or to the formation of silver chloride with an increased content of chlorine and chlorine compounds in the treated water. In this case, it is recommended that the water before processing be filtered or boiled, and during the processing, the electrolysis cell should not rest on the bottom or walls of the vessel, but the water should be stirred. If a precipitate still forms during processing, stir the water well before use.
Maintenance and storage rules
After finishing work, shake the electrolysis cell to remove water remaining on the electrodes. With a paper towel or soft cotton cloth, dry the cage and allow it to dry completely, then store it in the package.
With prolonged operation, it is possible for a dark deposit (atomic silver) to appear on the electrodes. Clean the electrodes carefully using a soft brush and rinse under running water.
Do not use solvents or bleaching agents. They can damage the plastic tip.
It is recommended to store the device in the cardboard packaging in a dry place at room temperature.
Payment
Ready to pay?
We accept Paypal. You may also use your Visa, Mastercard, American Express, or Discover card through Paypal
When you are ready to pay, Simply click the "Pay Now" button at the top of the eBay item page to submit a secure payment through checkout .
Purchase multiple items and save on shipping?
Delivery details
All items will be shipped to buyer's ebay address. Before you pay, please make sure your address in ebay matches the address you would like us to ship to.We are not responsible for any wrong or undeliverable addresses.
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs before making you purchase.
Items will be shipped within 1 business day on payment received.
About us
Our goal is to make sure you are a happy buyer and pleasant shopping with us.
Please email us before leaving any 1 or 2 ratings, negative feedback or open any ebay or paypal dispute.
We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem.