NQ HYBRIDS
Australian designed HHO hydrogen generators
Save the planet one step at a time
HHO END PLATES X 2 MAKE YOUR OWN DRY CELL
MAKE YOUR OWN 11 or 21 PLATE HYDROGEN CELL
YOU ARE BIDDING ON A SET OF (2) OF ACRYLIC END PLATES TO SUITE AN 11 or 21 PLATE DRY CELL.
"NO MORE CORROSION"
BUILD YOUR OWN
If you are wanting to build your own cell you will need 8 neutral plate and 3 power plates to build an 11 Plate Dry Cell 11 - Plate configuration -nnnn+nnnn-
Plate requirement for 21 Plate Dry Cell is 16 neutral plates and 5 power plates.
21 - Plate configuration -nnnn+nnnn-nnnn+nnnn-
ALL PART FOR YOUR DRY CELL ARE AVAILABLE AT OUR STORE!!
For more information message us
ALSO AVAILABLE AT NQ HYBRIDS
HHO CELLS, BUBBLERS, GAUGES, ¼ HOSE BARBS. ONE WAY CHECK VALVES, PWM’s ELECTROLYTELEVEL INDICATORS. EFIE’S. VAPORIZERS
Complete 11 Plate HHO Version 7 dry Cell kit
INCLUDES
To be Assembled 11 Plate Dry Cell
1800mm reinforced 1/4" tubing
8 Hose Clamps
12 Electrical Connectors
1 30 AMP Gauge
Purpose built HHO 1 litre Bubbler tank
1 Vaporizer/Scrubber/Spark arrestor
1 1/4 Check valve
30amp waterproof fuse
BONUS 30 AMP PWM (Pulse Width Modulator
30/40 AMP RELAY
All electrical tabs and fittings needed.
Pulse Width Modulators for Our HHO Dry Cell System
The PWM HHO Generator Controller Parts Specifications
20A RMS 30A MAX
2) Black ABS Plastic Enclosure
Size 4.7" x 3.2"x 2.2" with mounting flange
3) Cooling Fan - 60mm x 10mm Ball Bearing Fan
4) Adjustment Knob
All the holes are pre-drilled and unit comes fully assembled with the fan leads soldered to the board.
You will have to unmount the board by removing two screws and the pot retaining nut to make the connections to the PWM
To install just feed the wires through the large holes in the back of the box connect the two power wires to the two outside spade
connectors making sure the + wire goes to the + spade on the PWM and connect the HHO generator to the inside two spade connectors.
Full Installation Instructions come with this HHO pulse width modulator
The pulse width modulator (PWM) has an onboard trim potentiometer to control the amount of RMS voltage and current to your hydrogen booster
Your HHO Generator will run cooler and make more hydrogen which has greater ability to increase fuel mileage.
The PWM pulses at 100 Hz.
This PMW may be used on any 12 volt systems only
EFIE (Electronic Fuel Injection Enhancer)
Fuel Injection
Fuel injected vehicles use a computer and sensing devices to sense and maintain the correct air/fuel ratio. One of the key sensing devices is the oxygen sensor. Fuel injected vehicles have one or more oxygen sensors installed in the exhaust stream. The computer extrapolates what the air/fuel ratio is based on the amount of oxygen in the exhaust, as reported by the oxygen sensor.
When Hydrogen on demand device is installed, the petroleum based fuel is burned more completely. One of the results of this is that there is more oxygen (and less unburned hydrocarbons) in the exhaust stream. This is a good thing, and is in fact, what we are trying to achieve. However, the computer will perceive this condition as a "too lean" air/fuel mix. In other words, what is now a desirable condition in the exhaust will be interpreted as "not enough gas", and the computer will direct the fuel injectors to increase the amount of gas being pumped into the engine.The result is that the oxygen sensor and computer prevent efficient combustion from occurring
The Solution
The oxygen sensor "tells" the computer what the oxygen content is by providing a voltage on it's signal wire between 0 and 1 volt. 450 millivolts (.45 volts) means that the fuel/air mixture is correct. Higher values means the mix is rich (has too much gas), and lower voltages means the mix is lean. By adding voltage to the sensor's output, we can compensate for the additional oxygen in the exhaust.
The Electronic Fuel Injection Enhancer (EFIE) does exactly this. It adds a floating voltage to the top of whatever the oxygen sensor is putting out. It has an adjustment that allows you to control, to within a few millivolts, the amount of this added voltage. This allows the computer to be unaware of the additional oxygen content of the exhaust, and the electrolyzer can now achieve it's full potential in fuel savings.
Most cars have oxygen sensors both before and after the catalytic converter. The ones downstream from the converter do not need to be treated. Their data is used to determine when the converter has gone bad, but are not used in the air/fuel calculations. EFIEs are only needed for all upstream oxygen sensors
Wideband Quad EFIE
This is the EFIE for V6 and V8 engines that are equipped with wide band oxygen sensors. Note: Vehicles that use wide band sensors only use them upstream of the catalytic converter. The downstream sensors will still be narrow band. Therefore this product has 2 wide band EFIEs and 2 narrow band EFIEs
Wideband Dual EFIE
This is the EFIE for 4 cylinder engines that are equipped with wide band oxygen sensors, or any vehicle with one wide band and onenarrow band sensor. Note: Vehicles that use wide band sensors, only use them upstream of the catalytic converter. The sensors will still be narrow band. Therefore this product has a wide band EFIE and a narrow band EFIE
The HHO generator wiring has one important necessary feature: its ability to automatically turn on and off the HHO gas generator.
Instead of using a toggle switch to operate the HHO system, a relay is installed. What is a relay? A relay is an electrical switch that controls another circuit. It is also a device that contain an electrical winding motor inside which when powered up, will allow connection of 2 wires or circuits together. This is important in our Hydrogen on demand wiring which needs to be shut off when we stop the engine. If we are using a toggle switch to turn the HHO generator on, there is a chance that we can forget to shut the toggle switch off. HHO Is EXPLOSIVE The relay is activated when you turn on the ignition and is turned off accordingly. You can fit a toggle switch in between to deactivate the HHO system as a method of override. ALL NQ HYBRID SYTEMS COME WITH A 30 AMP RELAY
The Bubbler: is a simple flashback device, used to prevent the burning gas from entering the HHO gas generating chamber and creating an explosion.The HHO coming from the cell moves the electrolyte around. The bubbler acts a reservoir to help with heat build
ALL NQ HYBRID SYTEMS COME WITH A BUBBLER
ELECTROLITE
Now the installation of your unit should be complete. You are now going to Mix the Catalyst (electrolyte) with Distilled Water. KOH is recommended. Potassium hydroxide is an inorganic compound with the formula KOH. Its common name is caustic potash. Potassium Hydroxide is the best electrolyte for a Hydrogen Generator. We wont use any thing else for catalyst in our HHO Dry cells
The strength of your electrolyte mixture is what controls the amps drawn by your dry cell. To keep my unit running at 18 Amps or less and get a least 1 liter per minute of gas or more)
Start with 100gms of KOH to 900 gms of distilled water for start up , you may need to add more to get higher amps but run your unit with a weak solution to condition it first.
** Use "Safety First" rules when mixing KOH or other caustic materials. Mix thoroughly in a separate container.
* Once this has been mixed add to the reservoir, you should be able to see the water flowing into the dry cell. Bring the level up to the 3/4 mark on the reservoir and make sure to put the cap back on.
*** Now you HHO Dry Cell System should be fully functioning and ready for a test drive. Before you take a test drive start the vehicle, you should now see the water in full circulation. Double check for air and water leaks at this time BY getting a spray bottle and a teaspoon of dish soap once mixed spray on all of your hose connectors, bubbler cap and reservoir cap, if there are bubbles you have a leak and this needs to be fixed.
Always read MSDS data sheets when using corrosive / caustic solutions
Disclaimer In no event will nqhybrids be liable for any loss or damage to any vehicle or person including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from the use of our products. NQ Hybrids recommends a competent person installs there units and the purchaser does does his or hers own research on the use of these exsperimental fuel cells.
Added Bonus
All our Version SS cells are pre-treated with anti foam agent so you always get off to a good start.
All our cells are pressure tested and checked for Continuity.
Once connected to the bubbler and vaporizer this Cell is ready to go just add electrolyte and power up!
FOR MORE INFORMATION message Us.
If the question is not answered below, please give the size of engine in cc. age, make and if diesel or petrol when requesting information.
How does HHO work?With this HHO on demand System more of your primary fuel will be completely burned, smoothing out and improving overall operation. You will almost immediately notice a significant reduction in engine noise, as more complete combustion helps the engine to function correctly. For a about one month after HHO is installed the engine will continue to help remove built up carbon deposits which results from the unburnt fuel, This by itself will increase your economy and performance.
What are your cells made of?We use only 316L 18 gauge Stainless Steel in all our HHO Generators. The Plates Used in Our Dry Cells Are All Laser Cut and cross thatched. this does have an effect on performance and production of HHO gas!! The Acrylic end plates are 12mm thick rated at 145 degrees C. The inlet and outlet treads are1/4" The attachment bracket angles are aluminium 2 X 6mm SS wing nuts for easy connection to the power source. ALL STAINLESS BOLTS.
Does it make a difference if it is a Petrol or Diesel Engine?HHO will work on Diesel and Petrol and gas engines.
Is a HHO dry cell system hard to install?It is very simple, all our dry cells and kits have complete detailed installation instructions delivered with them. On average with the right tools and some mechanical know how it should not take longer than a few of hours.
What size cell do I need?
As a rule an 11 plate will do up to a 3 litre engine a 21 plate up to 4.5 litre engine and for the bigger engines up to 6 litre the Brutus 11 plate truck cell.
Do I need a PWM?
To make the HHO production more efficient the use of a PWM /CCPWM is recommended as control over the amount of amps the cell draws is important and higher pulses increase HHO production.
Do I need a EFFIE?
Not all engines need an EEFIE. It will depend greatly on the fuel type Diesel or petrol plus the year of manufacture. Please message for more info. Please state year and fuel type.
DISPATCH.
In most cases, we dispatch orders within 2 business days after full payment is received and cleared.
Weekends and public holidays are not recognised as business days.
TRACKING.
Australia
We post via Australia Post.
Generally, it takes 1-9 days to deliver parcel within Australia.
(Please Note: No tracking number will be provided via regular post, only on satchel items)
International
In most cases, international shipping takes around 12 - 35 business days.
If you do not receive your item on time, please contact us immediately for further assistance.
Some countries do not offer the availability of tracking at all- basic sea mail and air freight do not have tracking.
Tracking is only available on express shipping.
(Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost)
INSURANCE.
We are not responsible for the loss and/or damage during delivery.
Registration and insurance are available upon request.
No responsibility accepted for uninsured items or for handling by postal services.
Please contact us for quote - as a rule of thumb approx. 5% of the value of the item.
Items returned will be checked over for workmanship and operation.
If the product is found to be defective, it will be replaced free of charge.
Items that are returned due to incorrect item sent will be reissued with the correct item free of charge.
Items returned due to changing your mind or you have bought the wrong one will be refunded on a case by case basis.
The item once returned to us will be checked for damage .
If found to be in an 'as sent' state, we will refund the value less the initial cost of the postage plus a 15% restocking fee.
Due to new eBay policies, we are unable to disclose any contact information such as emails, phone numbers and addresses.
To get in touch, please use the eBay messaging system.
We constantly monitor our inbox and will reply to your message within 24 hours.
Hydrogen is a volatile colourless gas that has a low temperature ignition point. This gas also has no smell. Serious injuries and bodily harm can occur if the device is not handled or used properly!
NQ Hybrids takes no responsibility in damage to mechanical or bodily injury!
Australian DESIGNED
HHO generators designed by the leaders of HHO technology in Australia.
High quality materials
HHO manufactures use lower grades of Stainless steel like 304 and just run of the mill bolts and o rings. Here at NQ Hybrids, we only use high quality materials for our HHO generators and parts.
Help save the planet
NQ Hybrids strives to provide a high quality affordable HHO Generators and HHO Systems with the best possible customer service.