Highest Power, Integrated
one piece construction, true 4.8 amp ( 5 amp peak) dual USB charging socket, rubber sealing washer, and heavy weather sealing cap.
Ships from the USA.
Charges two iPods or two iPhones at the same time at full power.
This listing is for one USB dual charger socket with weatherproof cap. Attaches to your 12 volt source and allows you to charge USB accessories. #CP/SW
What is a true 4.8 Amps?
Many charger are nominally rated or not rated at all. Other charging socket output 1, 2.1, 3.1, 4.2 Amps, but these rating may only represent the maximum peak output rating and can not sustain that output for a prolonged period. Our chargers, including this one, at 4.8 amps, are true rated which means they can maintain the rated output current for an indefinite period. This allows you to charge your USB accessories at maximum power up to 30% faster. This charger's output is the highest in the industry. Each of the dual port can output a true 2.4 amps. Should your device require more than 2.2 amps the power is distributed as need to the individual ports up to 4.8 amps.
The socket body and charger are one piece, designed for outside use. The heavy weatherproof cap fits into and snaps over the front of the charger to keep moisture out when not in use. This cap, unlike other caps, covers all of the individual USB port openings. The rubber washer provide a waterproof seal and vibration resistant panel mount. The socket has 0.250 male spade type terminals for easy wire connections.
No LED, means less power consumption.
This
charger is rated for 4.8 amps 5 amps peak at 5 V and can accept two USB devices.
The socket fits in a 1-1/8” hole in panels up to 1-1/4 inch thick with the backing nut. Mounting plates available for thicker panels
Higher
volume discounts available for 10 or more contact us.
Options:
-Add a
USB plug connector boot. This is a vinyl boot that slips over your USB cable
connector such that when the connector is inserted into the socket the boot
covers the connection from weather. See item 110966193186
-Add a
socket boot to increase the weather resistance of the socket. The boot covers
the the wire contacts and has an exit for the wires. The socket boot may be
purchase one per assembly when you buy this item. For a straight boot (shown
above but not included in this listing) see this listing 120941435675. For a
right angle boot for tight installations see this listing 110791911918 .
-Add
a fuse holder to your socket installation. Always connect the socket to your
battery with a fuse in between. This listing is for an inline waterproof fuse
holder and a 15 amp ATO fuse. See listing 110968445581
-Add a rubber occlusive sealing socket washer. Makes an extra waterproof seal when mounting the socket against a panel. The washer goes between the socket flange or nut, and the panel to seal the assembly. See listing 301066433426
-Add wires with a fused 60 inch (5ft) wire harness to your socket assembly. The harness comes with of a fuse holder and fuse, and red and black wire connectors to attach to your socket and battery. See 121264213736
-Add a double mounting plate. Allows you to mount two socket products side by side for a professional installation. See listing 121267652997
-Extended warranty. This product comes with a one year warranty for damage during normal use. Just return it for repair or replace. If you want to extend the basic warranty period to three years, buy this option 301125941663
-Add a socket switch waterproof-Single pole single throw (SPST). Rubber switch cover and sealed back fits in a socket hole. Wire crimp connections. See 121422944323.
-Add a mounting hole bore. Allows you to drill or enlarge a hole in your panel or dash to mount this product. See 121486220109.
-FREE FREE FREE domestic shipping on these options when you buy the item in this product listing. Just buy this listing and the options you need at the same time. Then send us a message after, to combine shipping and we will refund your shipping for the options. Applies to one of each select option only when purchased together.
-Add a custom label or marker. A label frame fits around the front flange
face and allows you insert a labeled tag. See # 121742656759