DVR CAMERA CHARGER
Please note: this is a camera for security purposes and not to be used secretly. For convenience of charging phones also. Please do not engage in any illegal activities.
One. Product parameters:
Video format: AVI
Video coding: M-JPEG
Video resolution: 1920*1080
Video frame rate: 30fps
Motion detection record: support
Battery capacity: about 300mAh
Record time: about 110 minutes
Charge voltage: DC-5V 1A; DC-5V 2A; DC-9V 1.67A
Storage support: 8GB-32GB FAT32
Transmission speed: USB 2.0
Interface type: Micro USB
Two. Product operation:
The following operation is based on inserting the TF card correctly.
1. Charging:
The built-in rechargeable lithium battery, when the device power shortage, it can be charged through the following ways:
1). Connect the 5V charger;
2). Connect the mobile power supply;
3). Connect the computer USB port.
Note: When charging, the blue light is on,the red light flashes.Once full,the lights are always on.
2. Power on & Power off
On: press the power key for 2 seconds.
Off: press the power key for 5 seconds to turn off the device.
3. Video:
Video: press the power key 2 seconds, the red light is on,and the device enters into the standby mode.Click the power key once, the red indicator will flash 2 times then go off ,the device enters into the video mode.
Save: while recording, click the power key once to end the record, and the red indicator will be on, the device is back into standby mode.
One paragraph,10 minutes, support loop recording.
4. Motion Detection Mode:
After power on, the red light is on, the device is at the standby mode. Then click mode key once, the blue light is on and the device enters into motion detection mode.
In this mode, click the power key once,the blue light flashes,and the device is at the detecting state. Once it detects any moving objects within the range,the blue light goes off and it begins to record.The device will record for 2 minutes, if there is no moving objects, the blue light flashes again into detecting state.
Exit: Click the power button once to stop and save the video, return to standby mode, the blue lights will be on.
5. Infrared night vision lights switch:
Turn on: In any mode after power on, press the power button for 2 seconds and release, the blue light flashes 2 times, infrared night lights is turned on.
Turn off: In any mode, press the power button for about 2 seconds to release, and the blue light will flashes 4 times to turn off the infrared night vision function.
6. Record with charging:
When the device is power off, connect the device into a power source(the charger or power bank), and the blue light is on, the red light flashes,the device is under the charging state. Then click the power button once, the red light flashes three times and enters into the recording mode.
During recording, click the power button to exit the recording and save it. The device is back into the standby mode. You can click mode key to switch video or motion detection record. Otherwise, 5 seconds later,the device will be back into the charging state.
Note: The device can’t enter the video mode when connecting into the computer.
7. Reset:
In case of system error or malfunctioning, reset the device by inserting a pin to the reset hole.
8. Time setting:
1.
2.）TURN OFF the device and connect it to a computer.
3.）Locate the “time.txt” file, set the desired time using format 2019-01-01 19:25:26 Y and save the file.
4.）Disconnect the device from the computer then turn on the device. The time set is then complete.
* The device does not display time by default. Modify “N” in“time.txt” file to “Y” to enable the time display.The reference format is as follows:
1: 2019-01-01 19:25:26 Y (with time watermark display)
2: 2019-01-01 19:25:26 N (no time watermark display)
