AEM Water/Methanol Injection Kit for Turbo Diesel Engines 30-3301 TURBO DIESEL
LOWER EGT'S!
RUN MORE BOOST!
RUN MORE TIMING!
MAKE MORE POWER!!
Water/Methanol Injection Kit for Turbo Diesel Engines #30-3301
- The Vehicle Compatibility Table is only a Guide - Turbo Diesel Engines
V2 Water/Methanol Injection Kit, HD Controller - Internal MAP with 40psi max, 200psi WM Pump, 5 Gallon Reservoir, Conductive Fluid Level Sensor
Water/methanol injection (WMI) systems reduce air inlet temps and enhance combustion efficiency on turbo Diesel applications, which allows an engine to deliver more power with less effort. Water/methanol injection also offers a host of benefits that promote engine longevity, including the reduction of carbon deposits left by a Diesel’s exhaust gas recirculation (EGR) system. AEM’s Water/Methanol Injection Systems for turbo Diesel trucks and SUVs utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol injection system.
AEM’s on-demand, Boost Dependent progressive controller for its PN 30-3301 Diesel Water/Methanol Injection kit has an on-board MAP sensor (up to 40 PSI) with a molded in nipple for a boost hose pickup to ensure the proper amount of water/methanol injection at all points along the engine’s power curve. AEM’s engineers spent extensive time developing the HD water/methanol controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further improves charge air cooling and reduces EGTs.
The new HD controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the HD controller housings for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent HD controller housing has a molded-in, barbed nipple to accept a boost hose (up to 40 PSI) and a wiring legend on the back.
The wiring harnesses for AEM’s Water/Methanol Injection kits are terminated with a positive-lock connector on one end and have color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.
AEM’s PN30-3301 Diesel Water/Meth system’s low-profile 5 gallon tank includes a high-tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness, and baffles to reduce fluid slosh.
Features:
- Boost Dependent HD controller features large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs
- Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, integrated pump ground circuit and additional wire for optional on/off solenoid
- “Boost Safe†failsafe output included
- Heavy-duty high-pressure injection pump features integral fittings, a Santoprene diaphragm and EPDM seals to resist corrosion. Our pump’s quiet, smooth operation is almost undetectable
- Two precision-machined billet-aluminum injectors with integral check valves include multiple nozzles to cover a wide range of horsepower levels (500 cc/min & two 1,000cc/min)
- 5 gallon tank with anti-slosh technology and high tech conductive low-fluid sensor with positive lock connector (tank-less Boost Dependent HD Diesel water/methanol systems available, AEM Part #30-3303 includes
- Boost-Dependent controller design with on-board 40-PSI MAP sensor)
- 20 feet of Nylon injection tubing included
- LED dash light for system status and low fluid warning
Important Safety Notice Regarding Methanol
AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.
All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.
Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.
WARNING!
Improper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our forum or find a professional installer/tuner near you.
Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol.
FOR EU SHIPPING QUOTE GET IN TOUCH!
Same Day Worldwide Shipping!
All AEM products are available! Get in Touch!
- See our Online Shop -
* MAKE SURE YOU READ & UNDERSTAND ALL RETURNS & WARRANTY TERMS & CONDITIONS *
About Us
Our name says it all, FUEL PERFORMANCE, when it comes to Fuel Delivery we have it covered. Fuel Performance Limited is an Online Webshop that continues to grow from strength to strength. What are we known for? We offer unbeatable pricing on a continuously growing list of the biggest name brand performance parts in the world. In addition, we pride ourselves on providing specialised fitment kits to all parts wherever possible. We specialise in Fuel Pump Kits for Automotive, Automotive Performance, Motorcycles, Scooters, ATV, UTV, Tractors, Jetski's, Watercraft, Marine and Snowmobiles! Our aim is to provide fast and efficient service delivery of accurate fitments to our Customers. All orders must be placed via our Ebay Shop or Websites. We operate globally and have Offices, Resellers, Distributors & Warehouses worldwide.
Payment
We use PayPal for secure payment and customer protection. We do not store credit card details nor do we share customer details with any 3rd parties!
Shipping
Orders cannot be collected. All Prices Include FREE UK 1st Class Standard Delivery - (2-3 Working Days) We do offer express UK Next Day shipping which can be selected under the shipping options - 3pm Cut Off time! All Shipping options are available for the EU & Worldwide!
Terms
Please be aware that under no circumstances will FUEL PERFORMANCE LTD be held responsible for any labour or repair costs or any other costs incurred from parts found to be faulty, defective or incorrect or any other costs arising from parts supplied. Warranties: We offer full Manufacture Factory Warranty. Make sure you read product specific warranty terms & Conditions & procedures on the manufactures websites before purchasing. A replacement will not be dispatched until we receive the Faulty part back and it is tested and confirmed to be faulty by the manufacturer. The buyer is responsible for all return shipping costs. AEM & INNOVATE: AEM & INNOVATE offer Full Customer Tech Support which must be used before any Warranty will be handled. A RMA number must be obtained from the Manufacturer by the customer before any suspected faulty part can be returned to us. ** AEM / INNOVATE / ZEITRONIX do not Warranty Wideband O2 Sensors **
Returns
Returns are accepted within 30 Calendar days. Purchased Items must be in new unused condition and in the original packaging as you received it and the SEAL NOT Broken or Opened. It is your responsibility to make sure you are purchasing the correct item. The customer is responsible for all return shipping costs. If you receive your order and find something is missing or damaged you are to make contact with us within 24 hours of receiving your order.
