Metal detector Pinpointer Waterproof.
PULSE PI, ( rilevazione continua )
Il suo particolare design permette di
rilevare in qualsiasi ambiente, in particolare in zone erbose o fangose, su
terra, sabbia e in acqua dolce o salata.
CARATTERISTICHE:
·
Avviso
di rilevazione tramite luce e vibrazioni
·
Pinpointer
Waterproof segnala la rilevazione del bersaglio emettendo impulsi a vibrazione
e luce LED bianca.
·
Tecnologia
Pulse Induction (PI)
·
Consente
di effettuare ricerche in acqua salata o in qualsiasi tipo di terreno, anche
nella sabbia nera
·
Rilevamento
stabilità profondo
·
Circuiteria
avanzata mantiene distanza di rilevamento per tutta la durata della batteria
·
Intensità
di rilevazione proporzionale alla vicinanza dell’obiettivo
·
Come
ci si avvicina al bersaglio gli impulsi della vibrazione e la luce LED
aumentano
·
Sintonizzazione
automatica
·
Il
microprocessore del Pinpointer Waterproof non richiede regolazioni di alcun
tipo
·
Impermeabile
·
Design
impermeabile
·
completamente
sigillato consente la ricerca sotto la pioggia o sotto l’acqua ad una
profondità di 30 metri
·
Ottimo
per i subacquei!
Come funziona?
RILEVAZIONE
DELL ’OBIETTIVO
Il
Pinpointer Waterproof comunica attraverso impulsi a vibrazione e luce. Gli
impulsi aumentano in quantità più la piastra di ricerca si avvicina
all’obiettivo rilevato.
La
quantità degli impulsi è proporzionale alla dimensione ed alla distanza
dell’obiettivo rilevato.
Pinpointer
Waterproof PULSE PI
Più
grande è il bersaglio, oppure più la piastra di ricerca è vicina al bersaglio,
più alto è il numero di impulsi. La piastra di ricerca deve essere in movimento
per individuare un bersaglio. Muovere la piastra di ricerca avanti e indietro
lungo la superficie in cui si sta cercando. Il rivelatore comunica la vicinanza
al bersaglio solo una volta. Spostare leggermente la piastra e poi
riavvicinarsi all’obiettivo per ottenere la rilevazione successiva.
CARATTERISTICHE
TECNICHE
·
Tipo
di rilevazione: induzione di impulsi (PI)
·
Modalità
di ricerca: All-Metal (tutti i metalli )
·
Lunghezza
totale: 44 cm
·
Piastra
di ricerca ellittica
·
Diametro
piastra di ricerca: 13,5 cm x 11 cm ( 5,3” x 4,3” )
·
Peso:
310 g.
·
Alimentazione:
1 batteria da 9 volt ( INCLUSA )
·
Vano
batteria: tramite tappo a vite con guarnizione di tenuta stagna.
·
Cinghia
da polso. In cordino con regolazione scorrevole
·
Impugnatura:
37 mm di diametro con gomma antiscivolo
·
Subacqueo: 10 metri
·
Garanzia 12 mesi
Prestazioni
in aria:
moneta
di rame diametro 3 cm--------- rilevata a 8 cm
lattina
da bibita 16 cm
piccolo
anello in oro
7 cm
The unique sealed design allows
detecting in any environment including grass, mud, dirt, sand, black sand, or
even in water.
1. LAYOUT OF THE PINPOINT
PRODUCT FEATURES
• Vibration & light - When a target is located the detector alarms with pulses of vibration and
flashes of bright light from a white LED.
• Target distancing - As you get closer to the target the vibration and light will increase in quantity.
• Automatic tuning - Requires no adjustment.
• Waterproof - Sealed design allows hunting in the rain or in water.
BATTERY INSTALLATION
To open the battery compartment,
rotate the battery cover counter-clockwise.
Connect a standard 9 volt alkaline
battery to the battery connector and insert the battery into the detector. Then
turn the battery cover clockwise until hand tight to assure a water-tight seal.
OPERATING INSTRUCTIONS
Turn on the detector: Hold unit with the search coil up for about three seconds.
Light will flash. Two short pulses of vibration and a steady dim light indicate
unit is on.
Turn off the detector: After use, hold unit with the search coil up for about three seconds.
Light will flash. Two short pulses of vibration and no light indicate the unit
is off.
Note: If no metal is detected within
one minute, the unit will automatically turn off.
Low battery turn off: When the battery is low the unit will shut down automatically indicated by
four long pulses of vibration and bright light.
DETECTING A TARGET
After turning on the detector, hold it
with coil down to start detection. When target is located, the detector
indicates with vibration and bright light. These pulses increase in quantity as
the closer the search coil is to a detected target. The quantity of pulses is
proportional to the target size and distance. The bigger the target, or the
closer the search coil is to the target, the higher the pulse count. Movement
of the search coil is required to detect a target. Sweep the search coil back
and forth along the surface you are searching. Move the coil slightly away and
then re-approach the target to get the next detection.
HELPFUL HINTS
You have to hold the detector with coil down to start detection after turn
on. If you continue to hold the detector with the coil up, the detector will
not start operation.
You can secure the detector to your wrist using the attached wrist strap.
Before submerging the detector make sure the battery compartment seal is
secure.
Always use high quality batteries such as alkaline or nickel metal hydride
(NiMH).
IMPORTANT NOTES
• The
detection field projected resembles an oval shape, with the deepest depth of
detection
in the center of the coil.
• Raising the
detector’s coil up while in use will start the turn-off sequence, indicated by
a
blinking light and vibration. Lower the detector’s coil within 3 seconds
to continue
detecting.
• Unit will not
detect when the light is blinking in either the turn-on or turn-off sequence.
• As with any new
detector you should practice with known targets to develop your
searching technique.
GC-2008 Waterpfoof Metal Detector with Elliptical Coil |
Detection type: pulse induction |
Waterproof: 10M under water |
Search mode: all metal |
Sensitivity: 5cm for US quarter |
Automatic tuning |
Strong vibrating alarm |
LED light for dark environment |
Low battery automatic turn off |
Power:1x9v battery |