Notice!Notice!Notice!
This item do not include the power adapter, you need to buy an extra power adapter according to your requirement. So it only suitable for PoE professional customers.
If your device support IEEE802.3af or IEEE802.3at standard,then you should select 44 -57V power adapter (typical value is 48V) for them, instead of 12V.
Power adapter links:
http://www.ebay.co.uk/itm/112019199523
http://www.ebay.co.uk/itm/121742966259
(Usually for ensure the power supply is stable for a long time. it is recommended not to let the power load exceeds 80% of nominal value. so please choose a more suitable power adapter according to the number of camera you intend to connect and the total power. For example, you intend to connect 6 cameras, while each camera power consumption is 12Watt, the total power consumption is 6x12=72watt. Then select the 96Watt (48V2A) power adapter is enough. if the total power consumption is over 80watt then it is recommended to choose 144W (48V3A) power adapter.)
If your camera is with word “12V/PoE” as this picture shows, then please select 48V Power Adapter, do not select 12V Power Adapter. |
DSLRKIT PMID6P2U Passive PoE Injector Switch
8 Ports (2Uplink, 6 PoE) 10/100Mbps
Midspan Mode-B Unsolicited Power(4,5+/7,8-)
Wall Mount
This is an Passive Power Over Ethernet of 8 port 10 / 100Mbps-T Ethernet switches, including 6 unsolicited PoE Ethernet ports and 1 Uplink ports. DC port apply 9~55V power supply adapter(not included), any one of the 6 port can provide output power, each Ethernet port can provide network transmission speeds of up to 10 / 100Mbps , with Cat5 / 5e / 6 network cable.
This POE switch only support 10/100M connection, PoE ports do not support Gigabit ethernet connection, because "Power Link 3~8" port using 4,5,7,8 pin as power transfer, Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "Power Link 3~8" port, this will damage your device.
Gigabit(10/100/1000Mbps) ethernet device Please do not access "Power Link port" this will damage your device
Features:
Specification:
ALL Port: | Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。 | |
Power Link Port 3-8-: | any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs) |
Power LED | LED ON: power on. LED OUT: power off | |
LED Light LINK/ACT | LED ON Indicates the port is connected to a network device and has been started | |
LED OFF Indicates that this port is not connected to a network device or has not been started |
Standard | IEEE 802.3 10BASE-T Ethernet |
IEEE 802.3u 100BASE-TX Fast Ethernet | |
IEEE 802.3x Full-Duplex flow control | |
Protocol | CSMA/CD Ethernet |
Data Transfer Rate | Ethernet: 10Mbps (Half Duplex),20Mbps (Full Duplex) |
Fast Ethernet: 100Mbps (Half Duplex) ,200Mbps (Full Duplex) | |
IC Chips | IC Plus IP178G |
Network Media(Cable) | 10Base-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) |
100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) | |
PoE Power on RJ45 | Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8 |
DC Output: 9-55V, Per port Max 1A, | |
Number of Ports | 8 x 10/100Mbps Auto-Negotiation RJ45 ports with 8 PoE enabled (port-3 ~ port-8) |
Power Input | Supports INPUT 9-55V DC power supply |
Power DC port 5.5 x 2.1mm, inside positive (+) outside negative (-) | |
Power Consumption | 3.2 Watts (max. no PD connected) |
According to the actual power consumption of equipment | |
Temperature | Operation Temperature:0 ~40℃ (32 ~104℉ ) |
Storage Temperature: -40 ~70℃(-40 ~158℉) | |
Humidity | Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing |
Product Dimensions | 125mm W x 68mm D x 32mm H |
RAM Register Capacity | 64K bytes per device |
MAC Address List | 1K entries per device |
Frame Forward Rate | 10Mbps Ethernet: 14880pps/Port |
Item Included:
8pots 6PoE Unsolicited(Passive) PoE switch x1
(Power supply not included)